Advertisement
Advertisement
Table of Contents
Related Manuals for veise KS02A
Summary of Contents for veise KS02A
- Page 1 KS02A Keypad Digital Deadbolt Installation Guide / Programming Instructions Thank you for purchasing our products. Please review this manual thoroughly before operating your device. All pictures in this manual are for illustration purpose only. Actual product may vary due to product upgrade.
-
Page 2: Installation Overview
Installation Overview Programming Instructions STEP 1: Prepare the door and check dimensions At a Glance P 15 Factory Default Settings STEP 2: Install the latch and strike How to Use Troubleshooting STEP 3: Install exterior assembly P 11 Definitions Information & Safety Warnings STEP 4: Install interior assembly P 12 Code Format... - Page 3 INSTALLATION OVERVIEW Battery Cover (G) Interior Assembly (F) Mounting plate (E) Exterior Assembly Mounting Interior Assembly plate Screws (J) Screws (K) Latch (C) Strike (D) Reinforcement plate (D-1) Backup key (A) Latch Screws Strike Screws...
-
Page 4: Parts List
Parts List Exterior Assembly x1 Strike x1 Backup Key x2 Latch x1 Reinforcement Plate x1 (optional) Mounting Plate x1 Interior Assembly x1 Battery Cover x1 Strike Screws x4 Latch Screws x2 Interior Assembly Reset Tool x1 Drive-In Collar (Optional) Mounting plate Screws x2 Screws x3 If any parts are missing or damaged, please contact Customer Support. - Page 5 STEP Prepare the door and check dimensions 2-3/8" or 2-3/4" (60 or 70mm) Measure to Measure to confirm confirm that the that the backset is hole in the door is either 2-3/8" or 2-1/8" (54mm). 2-3/4" (60 or 70mm) Measure to confirm that the hole in the door edge is 1"...
- Page 6 STEP Install the latch and strike Determine backset and adjust the latch No adjustment is required. Proceed to next step. Slotted hole is NOT centered. Hold the latch in front of the door hole, Rotate and pull the with the latch face flush against the latch as shown to door edge.
- Page 7 Use a screwdriver to test if deadbolt works smoothly. IMPORTANT: Install strike on the door frame. Make sure the hole in door frame is drilled a minimum of 1" (25mm) deep. (Optional)
-
Page 8: Install Exterior Assembly
STEP Install exterior assembly IMPORTANT: Unlocked Locked Before installation, make sure the latch is fully retracted (in the unlocked position) Keep parallel to door edge. Tourque blade Mounting plate Screws(J) Secure the mounting plate with the With the latch fully retracted (in the unlocked supplied screws. -
Page 9: Install Interior Assembly
STEP Install interior assembly Insert the cable connector to the Push the battery cover out in socket. Push the the direction as illustrated. connector in firmly until it is completely IMPORTANT: attached. Do not load batteries until lock is completely installed. Keep the thumb turn in vertical position and install Attach Interior the interior assembly. - Page 10 STEP Detect left/right hand door installation This step is required and crucial for the lock IMPORTANT: to operate properly. Reset the lock to teach the lock the orientation of the door. While the door is OPEN and Press and hold the Reset button on Load the 4th battery and keep holding UNLOCKED, load 3 AA batteries the interior assembly by using the...
-
Page 11: Programming Instructions
PROGRAMMING INSTRUCTIONS At a Glance Exterior Assembly Interior Assembly Multi-Function Battery Cover Button(MFB) Keypad Reset Button Fingerprint Thumb Turn Keyhole... -
Page 12: How To Use
How to Use UNLOCK the door from inside UNLOCK the door from outside Rotate the thumb turn to Master code + User code + Unlock position. LOCK the door from outside LOCK the door from inside Auto Lock Mode Manual Mode Auto Lock Mode Manual Mode In Auto Lock mode, the bolt... - Page 13 Definitions Programming Basic • Master Code • Silent Mode Required for programming and feature settings. Master code can be The beep sounds when pressing keypad can be muted. But you will used to unlock the door under vacation mode. The default master still hear low battery and system alerts.
-
Page 14: Code Format
Code Format Programming Basic 12345678 1. Master Code(4 to 10 digits): The default Master Code is . It is required that you change it to a code of your own before programming. 2. User Code: 20 User Codes (4-10 digits), 1 one-time User Code and 20 fingerprints can be programmed and stored in the lock. 3. -
Page 15: Quick Setup
12345678 The default Master Code is IMPORTANT: Quick Set Up It is required that you change it to a code of your own before programming. + Master Code + Press New Master Code + New Master Code + Change Master Code Succeed Wait for long green lights Wait for green light flash... - Page 16 Silent Mode Disabled + Master Code + Press Green light flash Silent Mode Silent Mode Enabled Wait for long green lights Wait for green light flash Green light flash Auto Lock Enabled Press + Master Code + Green light flash Auto Lock Auto Lock Disabled Wait for long green lights...
-
Page 17: Factory Default Settings
Factory Default Settings How to Reset? Reset button The resetting will delete all User Codes stored IMPORTANT: in the lock. Step 1. Keep the door open and unlocked. Step 2. Press and hold the Reset button, at the same time take out one battery and then place it back. -
Page 18: Troubleshooting
Troubleshooting Why does not the latch extend but the motor is rotating when Why does my lock only work properly when the backup key is resetting my lock? in? Why am I unable to pull the key out in the unlocked position? Improper installation may have caused the issue. -
Page 19: Information & Safety Warnings
Information & Safety Warnings • Protect your User Codes and Master Code. • Care should be taken to ensure a long-lasting finish. When cleaning is required use a soft, damp cloth. Using lacquer thinner, caustic soaps, • Restrict access to your lock’s interior assembly and routinely check your abrasive cleaners or polishes could damage the coating and result in settings to ensure they have not been altered without your knowledge.
Need help?
Do you have a question about the KS02A and is the answer not in the manual?
Questions and answers