Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for DeWalt FLEXVOLT DCS520
Summary of Contents for DeWalt FLEXVOLT DCS520
- Page 1 Instruction Manual DCS520 60V Track Saw...
- Page 2 Definitions: Safety Alert Symbols and Words This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk of personal injury or property damage. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
-
Page 3: General Power Tool Safety
Fig. A2 GENERAL POWER TOOL SAFETY c ) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase WARNINGS the risk of electric shock. WARNING! Read all safety warnings and all d ) Do not abuse the cord. Never use the cord for instructions. -
Page 4: Safety Instructions For All Saws
d ) Remove any adjusting key or wrench before b ) Use power tools only with specifically designated turning the power tool on. A wrench or a key left battery packs. Use of any other battery packs may attached to a rotating part of the power tool may create a risk of injury and fire. - Page 5 Further Safety Instructions for All Saws saw is accidentally dropped, guard may be bent. Check to make sure that guard moves freely and does Kickback Causes and Related Warnings not touch the blade or any other part, in all angles Kickback is a sudden reaction to a pinched, bound or and depths of cut.
-
Page 6: Additional Safety Information
Additional Safety Information RPM ....revolutions per n o ....... no load speed minute n ......rated speed WARNING: ALWAYS use safety glasses. Everyday sfpm ....surface feet per ...... earthing terminal eyeglasses are NOT safety glasses. Also use face or minute dust mask if cutting operation is dusty. - Page 7 battery pack can explode in a fire. Toxic fumes and can exempt the pack from certain shipping regulations that are imposed upon the higher Watt hour batteries. materials are created when lithium ion battery packs are burned. The battery label indicates two Watt hour ratings (see •...
- Page 8 spent nickel cadmium, nickel metal hydride or lithium-ion Minimum gauge for Cord sets batteries in the trash or municipal solid waste stream and Total length of Cord in Feet Volts the Call 2 Recycle® program provides an environmentally (meters) conscious alternative. 120 V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7) Call 2 Recycle, Inc., in cooperation with D...
-
Page 9: Charger Operation
Charging a Battery (Fig. C) The compatible charger(s) will not charge a faulty battery pack. The charger will indicate faulty battery pack by 1. Plug the charger into an appropriate outlet before refusing to light or by displaying a problem pack or charger inserting battery pack. -
Page 10: Storage Recommendations
the battery pack in an air temperature below +40 °F DO nOT use under wet conditions or in presence of (+4.5 °C), or above +104 °F (+40 °C). This is important flammable liquids or gases. and will prevent serious damage to the battery pack. This heavy-duty track saw is a professional power tool. DO nOT let children come into contact with the tool. -
Page 11: Operation
6. Use the hex wrench to turn the blade clamping screw 2. Loosen the riving knife adjustment screw with a hex 22 counter-clockwise to remove. wrench and set the riving knife as shown in Figure E. 24 7. Remove the outer flange and used blade . - Page 12 Proper Hand Position (Fig. G) Fig. H WARNING: To reduce the risk of serious personal injury, ALWAYS use proper hand position as shown. WARNING: To reduce the risk of serious personal injury, ALWAYS hold securely in anticipation of a sudden reaction. Proper hand position requires one hand on the front handle 11 ...
- Page 13 of kickback. Change blades when it is no longer easy to In conjunction with additional accessories, exact angled push the saw through the cut, when the motor is straining, cuts, mitre cuts and fitting work can be completed with the or when excessive heat is built up in the blade.
- Page 14 Fig. J Fig. L Fig. K 45˚ 0˚ Speed Adjustment (Fig. A2) The speed can be regulated between 2500 and 4200 rpm using the speed wheel . This enables you to optimize 19 the cutting speed to suit the material. Refer to the following chart for type of material and speed range.
-
Page 15: Maintenance
Dust Extraction (Fig. A2) materials used in these parts. Use a cloth dampened only with water and mild soap. Never let any liquid Your tool is fitted with a dust port 17 get inside the tool; never immerse any part of the tool WARNING: DO NOT direct sawdust toward yourself into a liquid.