Maintenance Of The Pergola; Extraordinary Maintenance - Gibus MEDITERRANEA Series Use And Maintenance Manual

9.2

MAINTENANCE OF THE PERGOLA

IMPORTANT: please open and close the awning periodically and check periodically
the correct operation of the parts. Do not leave the product unused for long periods.
In order to keep the product in perfect operating conditions and safe proceed as follows:
• Yearly (or after any extreme weather events):
- visually inspect the bearing structure;
- inspection of the tightening and the integrity of bolts and nuts, as well as screws. Make sure
that the ground and the wall fixing devices are in perfect condition. Check the condition of the
floor around the fixing devices (in particular, make sure that there are no cracks and that the
screws are properly tightened);
- make sure that the gutters along the perimeter and the gutters of the brise soleil blades are
clear of leaves or other debris. Remove the elements that prevent water from flowing out and
lubricate the moving parts with a drop of Teflon spray, if necessary.
- check the operation of the remote controls, the sensors and the lighting installation. Check the
efficiency of the grounding.
- clean the surface, if it is necessary, to remove dirt and dust. Clean the surface with a paper rag
and a wet sponge as explained in the previous paragraph.
9.3

EXTRAORDINARY MAINTENANCE

For extraordinary Maintenance within the 2nd year from
installation and in subsequent years (mandatory for
extending the warranty) follow the other regulations found
in the "Product Maintenance Technical Sheet".
ATTENTION! The maintenance work is to be
carried out by qualified and trained personnel. Call
for a Gibus specialised technician.
38 52
Page of
USE AND MAINTENANCE MANUAL
Code MUT 104
PRODUCT MAINTENANCE CHECK LIST
BIOCLIMATIC PERGOLA
CUSTOMER HOLOGRAM N°
Date:
No. "Maintenance operation" list
CHECK CORRECT MOVEMENTS – BRISE SOLEIL BLADES
1 MOVE THE BLADES COMMANDING A FULL RUN FROM COMPLETELY CLOSED TO COMPLETELY OPEN
AND VICE VERSA
2 CHECK THERE ARE NO FOREIGN BODIES BLOCKING MOVEMENT, REMOVE ANY THAT ARE FOUND
3 CHECK THE CORRECT POSITION OF THE DRAW BAR AT THE OPENING AND CLOSING ENDSTOPS
4 LUBRICATE MOVING PARTS WITH TEFLON SPRAY (DRAW BAR PLASTIC SADDLES – GUIDE PORTION
CAMS COUPLED WITH WHEELS)
5 USE THE REMOTE CONTROL TO COMMAND THE LIMIT LEARNING PROCEDURE
CHECK THE STATE AND FOR ANY OBSTRUCTIONS IN PERIMETER GUTTERS AND BRISE SOLEIL BLADE GUTTERS.
CHECK THE STATE AND FOR ANY OBSTRUCTIONS IN COLLARS AND CORNER DRAIN PIPES AT THE TOP AND
BOTTOM OF THE COLUMNS.
6 INSPECT GUTTERS, DRAINPIPES, COLUMNS, DRAINS
7 REMOVE ANYTHING THAT OBSTRUCTS THE WATER DOWNFLOW, REMOVING ANY FOREIGN PARTS
(E.G. LEAVES, PINE NEEDLES, ETC.)
8 CHECK THE SEALS ARE IN GOOD CONDITION: (ESPECIALLY CORNER GUTTERS AND GUTTER PLUGS
HOLDING THE PERIMETER LED LIGHTS)
CHECK THE SUPPORTING STRUCTURE
9 CHECK THE GOOD STATE AND TIGHTNESS OF THE NUTS AND BOLTS
10 CHECK THE FLOOR AND WALL ATTACHMENTS ARE IN PERFECT CONDITION
11 CHECK THE CONDITION AROUND THE ATTACHMENTS (ESPECIALLY THAT THERE ARE NO CRACKS AND
THAT THE SCREWS ARE TIGHT), IF THERE ARE PROBLEMS INFORM THE CUSTOMER
CHECK THE SENSORS, AUTOMATISMS AND ELECTRIC PARTS
12 CHECK THE REMOTE CONTROLS WORK AND THE BATTERIES ARE CHARGED
13 CHECK THE SENSORS WORK CORRECTLY (IF INSTALLED)
14 CHECK THE LIGHTING SYSTEM WORKS CORRECTLY (IF INSTALLED)
15 CHECK THE AUDIO SYSTEM WORKS CORRECTLY (IF INSTALLED)
16 CHECK THE ELECTRIC CONNECTIONS ARE UNDAMAGED
CHECK THE LATERAL DROP AWNINGS OR SIDE WINDOWS (IF INSTALLED)
17 CHECK THEM ACCORDING TO THE TYPE OF SIDE WINDOWS THAT ARE INSTALLED
18 RECORD THE WORK IN THE MANUALS OR TECHNICAL MAINTENANCE CHARTS FOR EACH PRODUCT
www.gibus.com
Rev. 1
MED TWIST
MED JOY
Check
OK/NO
□ ____
□ ____
□ ____
□ ____
□ ____
OK/NO
□ ____
□ ____
□ ____
OK/NO
□ ____
□ ____
□ ____
OK/NO
□ ____
□ ____
□ ____
□ ____
□ ____
OK/NO
□ ____
□ ____