Assembly - Craftsman 115 Operator's Manual

_1_ WARNING: Do not allow famiSa_tywith tools to
make you careJess.Remember that a careless
fracbon of a second is sufficientto intiict serious
]njury.
_k WARNING: Always wear safety gogglesor safety
glasses with side shields when operating tools.
Failureto do so could result in objects being thrown
into your eyes, resulting in poasibisserious injury.
_1= WARNING: Do not use any attachments or acoas-
series not recommended by th_ rna_u_oturer of
this tool. The use of attachments or accessories not
recommended can result in serlous personalinjury.
APPLICATIONS
You may use this tool for the foUowingpurposes:
• Drilling in wood
• Drilling in ceramics, plastics, fibergtess,and laminates
• Ddlling in metals
• Mbdng paint
CAUTION: If at any point during the charging
process none of the LEDs are lit, remove the bat-
tary pack _'om _e chargerto avoid damaging the
product. DO NOT insert another battery.Return the
charger and battery to your nearest service center
for service or replacement.
CHARGING THE BAI-I'ERY PACK
The battery pack for this tool has been shippedin a low
charge conditionto prevent possible problems.Therefore,
you should charge overnight priorto use.
NOTE: Batteries will not reach furl oharge the first time
they are charged. Allow several cycles (operationfollowed
by recharging]for them to become fully charged.
• Charge battery pack only w_ththe charging assembly
provided.
• Make sure power supply is normal householdvoltage,
120 volts, 60 Hz, AC on_y.
• Connect charger to power supply.
• Place battery pack in charging stand.Align raised db
on bat_eP/pack with groove in chargingstan_. See
F/gum 2.
• Press down on b_ttsry pack to be'sure contacts on
battery pack engage properlywith contacts in charging
stand.
• The charge indicator light (LED), located on the charg-
ing stand, wi_ I'_ghtup red and glow when the eharger
is properly connected to power supply. "Thislight
indicates the charger is operating property. It will
remain on unbl battery pack is removed from charging
stand or charger is disconnectedf_om power supply.
• After normaJusage, 3 hours or k_saof charging time is
required to hJfty recharge battery pack.
NOTE; If both red and orange LED ind_caforsglow, the
battery pack is deeply or compk=.te0j d (scharged, and
6 hours er longerof chargingtime }s required to fully
recharge thebattery p ack,
If thecharger does notcharge _hebattery p ack, or
the orange LED corr_nues to glow after more than 30
m_nutes of chsrg'lng, r eturn the battery pack and charg-
ing e.ssemb[yto your nearest Sears Repair Center for
electrical check.
• The battery packwill become slightlywarm to the
touch while charging.This is normal and does not
indicate a problem.
m Do not place charger in an area of extreme heat or
cold. It wilt work best at normal room temperature.
II When batteries become fully charged, unplug charger
from power supply and remove the battery pack.
CHARGING A HOT BA'rrt=RY PACK
When using your tool continuously, the batteries In your
battery pack will become hot. You should let a hot battery
pack cool down for approximately 30 minutes before
attempting to recharge.
NOTE: This situationorgyoccurs when continuoususe of
your ddll causes the batteries to become hot. It does not
occur under nonT_ circumstances.Refer to =CHARGING
THE BATTERY PACI_ for normal recharg]ng of battedes.
If the chargingaasembly does not charge your battery
pack under normal circumstances,return both the battery
pack and chargingassembly to your nearest Sears Repair
Center for electrical check.
10