Related Manuals for Vonets VBG1200
Summary of Contents for Vonets VBG1200
- Page 1 VONETS - Wireless Module/Finished Product Wireless module/WiFi product VM300/VM5G/VBG1200/VAP11AC Quick Setting Guide...
- Page 2 VONETS is the registered trademark of Shenzhen HouTian Network Communication Technology Co.,Ltd. The other all trademarks or registered trademarks mentioned in this documents are belong to the individual owners. The product specifications and information technology mentioned in this manual are just for reference, if any updates, without other notice.
- Page 3 VONETS - Wireless Module/Finished Product Form2 Power Supply Parameters List Typical Power Model Power Supply Voltage Input Power Supply ≥5W VM300 DC5V--15V 5V/1A VM5G/VBG1200 DC5V--15V ≥10W 5V/2A VAP11AC DC5V--24V...
-
Page 4: Table Of Contents
VONETS - Wireless Module/Finished Product Contents Chapter 1 Application Mode ..............1 1.1 Bridge + Repeater Mode ......................1 1.2 Router Mode ..........................2 Chapter 2 Bridge+Repeater Mode Configuration Instruction ....3 2.1.1 Device Connection ........................3 2.2 Bridge+Repeater Application Configuration ................4 2.3 AP Application Configuration ....................... -
Page 5: Chapter 1 Application Mode
VONETS module/WiFi product as WiFi bridge, it must be configured to source WiFi hotspot parameters, can be used for devices only with Ethernet ports to access wireless networks. ⚫ WiFi AP： VONETS module/WiFi product as WiFi AP, it can achieve wireless access to wired LAN, no configuration required, plug and play. -
Page 6: Router Mode
“WAN/LAN interchange” so that the Ethernet cable is WAN port to use the broadband dialing function. ⚫ VONETS module/WiFi product is used as a wireless router. WAN port can be set to connect to the WiFi hotspot for use as a secondary router. -
Page 7: Chapter 2 Bridge+Repeater Mode Configuration Instruction
2.1 Method 1: Log in to the device's Web configuration page to configure 2.1.1 Device Connection Power on VONETS module/WiFi product by 5V/2A power supply, then connect to PC, there are two connection ways as below: A. Computer is wired connected to LAN port of VONETS module/WiFi product;... -
Page 8: Bridge+Repeater Application Configuration
(After the WiFi parameters are configured, the WiFi will be disconnected, that is normal.) 2.2 Bridge+Repeater Application Configuration The configuration steps of VONETS module/WiFi product for WiFi repeater and WiFi bridge are basically the same, so this manual combines the configuration instructions of the two application modes. - Page 9 ⚫ The option “The configuration parameters of WiFi repeater security is synchronized with source hotspot” is default ticked, it means the SSID of VONETS repeater is associated with the SSID of the source hotspot, and the WiFi password is the same as the password of the source hotspot;...
- Page 10 VONETS - Wireless Module/Finished Product 5. Click “Reboot”, VONETS module will connect to the configured WiFi hotspot automatically, if connection is successful, the WiFi LED light will flash quickly;...
-
Page 11: Ap Application Configuration
VONETS module/WiFi product can be configured as an AP application. The wireless terminal device can connect to VONETS module/finished product hotspot to connect to the network; however, it is best to change its WiFi name and password for network security. - Page 12 3. Revise WiFi password, in “WiFi Repeater”----“WiFi Security”, enter new WiFi password in “Pass Phrase”, click “Apply”; 4. “WiFi Tx Power” of VONETS module/WiFi product can be changed, jump to “System Settings”---- “Advance Settings”, choose suitable transmit power, then click “Apply”;...
-
Page 13: Chapter 3 Router Mode Configuration Instruction
Chapter 3 Router Mode Configuration Instruction 3.1 Change device mode 1. Power on VONETS module/WiFi product by 5V/2A power supply, then connect to PC, there are two connection ways as below: A. Computer is wired connected to LAN port of VONETS module/WiFi product;... - Page 14 VONETS - Wireless Module/Finished Product （Recommend Method） B. Computer wirelessly connects to the WiFi signal of VONETS module/WiFi product, its default hotspot parameters are as follows: WiFi SSID: VONETS_****** (corresponding to VONETS device MAC address) WiFi password: 12345678 (After the WiFi parameters are configured, the WiFi will be disconnected, that is normal.) 2.
-
Page 15: Wan Port Setting
3.2 WAN port setting 3.2.1 WAN/LAN exchange In routing mode, the Ethernet port of VONETS module/WiFi product is divided into a WAN port and a LAN port, and WAN/LAN can be interchanged. The Ethernet port of VM300 module / VAP11AC finished product defaults to WAN port. The Ethernet cable defaults to LAN port. -
Page 16: Wan Port Connection Method
ISP (Internet Service Provider) to provide Internet account and password. ⚫ WiFi: WAN port connection type is selected as “WiFi”, VONETS module/WiFi product uses a built-in WiFi network card (used to connect to the source hotspot) as a WAN port, and all Ethernet ports as LAN ports, while providing WiFi hotspot functions. -
Page 17: Wan Port Wired Connect Network--Pppoe
In “WAN settings”, select “Basic settings”, change the connection type to “PPPoE (ADSL)”, then enter the Internet account and password provided by the ISP (Internet Service Provider), click the “Apply” button, and then reboot VONETS module/WiFi product, then can access to network. 3.2.5 WAN port wireless connect network---- WiFi 1. - Page 18 ⚫ The option “The configuration parameters of WiFi repeater security is synchronized with source hotspot” is default ticked, it means the SSID of VONETS repeater is associated with the SSID of the source hotspot, and the WiFi password is the same as the password of the source hotspot;...
-
Page 19: Set Wifi Hotspot Parameters
Remark 1 for the description of the LED light.) Remark 3: After VONETS module/WiFi product sets the WAN port to access the WiFi hotspot in the routing mode, its LAN port IP is still 192.168.254.254, and the terminal device also obtains the IP address of the same network segment, can login configuration page by 192.168.254.254 or... - Page 20 VONETS - Wireless Module/Finished Product 2. Revise WiFi password, in “WiFi Repeater”----“WiFi Security”, enter new WiFi password in “Pass Phrase”, click “Apply”; 3. Reboot device, jump to “System Settings”---- “Reboot Device”, click “Reboot”, when it is finished, all revised options will take effort.
-
Page 21: Appendix Frequently Asked Questions
VM5G: http://www.vonets.com/serviceView.asp?D_ID=306 VBG1200: After the device is powered on for about 60 seconds, press and hold the Reset button for 5 seconds and then release, the blue indicator light will flash a few times, and then the device will automatically restore the factory default parameters (the restoring process takes about 80 seconds). - Page 22 PC has been connected the device by WiFi or Ethernet cable, but user can’t log in the device WEB page, or after log in the WEB it shows error? ⚫ Reason 1. The users don’t use the browser recommended by VONETS(IE,Google Chrome, Safari, the mobile phone browser);...
- Page 23 VONETS - Wireless Module/Finished Product FCC STATEMENT : This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Need help?
Do you have a question about the VBG1200 and is the answer not in the manual?
Questions and answers