Table of Contents
Advertisement
Inverter with Blue Connect radio communication
system
IMMP1.1W – IMMP1.5W
Single-phase Inverter for single-phase motor pump
IMMP1.5W-BC
Single-Phase Inverters for Single-phase motor pump with Blue Connect system
IMTP1.5W
Single-phase Inverter for three-phase motor pump
IMTP1.5W-BC
Single-phase Inverter for three-phase motor pump with Blue Connect system
ITTP1.5W-BC
Three-phase Inverter for three-phase motor pump with Blue Connect system
Operation and maintenance handbook
ENG
EC.086.222
Advertisement
Table of Contents
Related Manuals for electroil Archimede IMMP1.1W
Summary of Contents for electroil Archimede IMMP1.1W
- Page 1 Inverter with Blue Connect radio communication system IMMP1.1W – IMMP1.5W Single-phase Inverter for single-phase motor pump IMMP1.5W-BC Single-Phase Inverters for Single-phase motor pump with Blue Connect system IMTP1.5W Single-phase Inverter for three-phase motor pump IMTP1.5W-BC Single-phase Inverter for three-phase motor pump with Blue Connect system ITTP1.5W-BC Three-phase Inverter for three-phase motor pump with Blue Connect system Operation and maintenance handbook...
-
Page 2: Table Of Contents
(fig. 1), and the software version, reading the two numbers showed on the led bar, switching-on the input supply line. Figure 1: serial number of the inverter ELECTROIL IMMP1.1W – IMMP1.5W – IMMP1.5W-BC – IMTP1.5W – IMTP1.5W-BC – ITTP1.5W-BC - ENG... -
Page 3: Working Conditions
The use of non-original components may endanger others and can lead to loss of warranty. Misdirect working conditions The working security is guaranteed only for the conditions described in chapter 2 of this handbook. The values shown cannot be exceeded ELECTROIL IMMP1.1W – IMMP1.5W – IMMP1.5W-BC – IMTP1.5W – IMTP1.5W-BC – ITTP1.5W-BC - ENG... -
Page 4: Assembling And Installing
Fig. 3: Inverter connections 3) Motor pump voltage supply (2P+GND+Schuko plug for 1) Inverter voltage single-phase, 3P+GND for three- supply 230Vac 2) Pressure phases (2P+T, schuko) transducer ELECTROIL IMMP1.1W – IMMP1.5W – IMMP1.5W-BC – IMTP1.5W – IMTP1.5W-BC – ITTP1.5W-BC - ENG... -
Page 5: Connecting The Pressure Transducer To New Waterworks System
Use any other ¼ "F hole on the pump hydraulics connections, possibly • removing the cap (such as a hole for venting air); Fig. 7: mounting transducer to venting air hole on the delivery pump ELECTROIL IMMP1.1W – IMMP1.5W – IMMP1.5W-BC – IMTP1.5W – IMTP1.5W-BC – ITTP1.5W-BC - ENG... -
Page 6: Connecting The Pressure Transducer To Old Waterworks System
IMMP1.1W, IMMP1.5W, IMMP1.5W- BC, please connect it following the scheme below (C1, fig. 11, not included). Figura 11 – Single-phase motor connection ELECTROIL IMMP1.1W – IMMP1.5W – IMMP1.5W-BC – IMTP1.5W – IMTP1.5W-BC – ITTP1.5W-BC - ENG... -
Page 7: Inverter Electric Connection To Line
Pump power kW on single-phase 230V version on three-phase 400V version 0.5 (0.75 Hp) 0.75 (1 Hp) 1.1 (1.5 Hp) 1.5 (2 Hp) Table 2: Magneto-Thermal protections ELECTROIL IMMP1.1W – IMMP1.5W – IMMP1.5W-BC – IMTP1.5W – IMTP1.5W-BC – ITTP1.5W-BC - ENG... -
Page 8: Access To The Electronic Board
Inverter box, protecting them to humidity, water and dust. Do not practice others holes to the Inverter case to avoid damages or decrease of the protection and insulation grade and interruption in anticipation of the guarantee. ELECTROIL IMMP1.1W – IMMP1.5W – IMMP1.5W-BC – IMTP1.5W – IMTP1.5W-BC – ITTP1.5W-BC - ENG... -
Page 9: Electronic Board Connections
Starting pump; start Self-Regulation Test on the first installation or after a RESET Stop of the motor pump Fig. 16: Control panel Table 3: Buttons description ELECTROIL IMMP1.1W – IMMP1.5W – IMMP1.5W-BC – IMTP1.5W – IMTP1.5W-BC – ITTP1.5W-BC - ENG... -
Page 10: Programming
RESET before self-regulation test, is necessary to perform this following: ELECTROIL IMMP1.1W – IMMP1.5W – IMMP1.5W-BC – IMTP1.5W – IMTP1.5W-BC – ITTP1.5W-BC - ENG... -
Page 11: Checking The Pump Stop For Minimum Flow
7 regulating the value of the selected function on a variation range indicated, on a scale from 0 to 10. ELECTROIL IMMP1.1W – IMMP1.5W – IMMP1.5W-BC – IMTP1.5W – IMTP1.5W-BC – ITTP1.5W-BC - ENG... - Page 12 Step: 0.5 mA value of the transducer pressure transducer Pressure Adjustment of the pressure 10..20 Bar 16 Bar transducer range. Step: 0.5 Bar transducer measure range ELECTROIL IMMP1.1W – IMMP1.5W – IMMP1.5W-BC – IMTP1.5W – IMTP1.5W-BC – ITTP1.5W-BC - ENG...
- Page 13 If the high value of the starting current cause problems on the magneto-thermal switch protection try reduce this current with F6 and verify that the torque remains enough. ELECTROIL IMMP1.1W – IMMP1.5W – IMMP1.5W-BC – IMTP1.5W – IMTP1.5W-BC – ITTP1.5W-BC - ENG...
-
Page 14: Protections And Alarms
All Alarms from A1 to A6 (table 7) are showed with the corresponding Led on the circular Led bar and the red Alarm Led, that is flashing if the protection have automatic re-start otherwise is fixed if the protection need a manually re-start doing STOP then START. ELECTROIL IMMP1.1W – IMMP1.5W – IMMP1.5W-BC – IMTP1.5W – IMTP1.5W-BC – ITTP1.5W-BC - ENG... -
Page 15: Solution On The Most Common Installation And Working Problems
(STOP and – button during 5 seconds) and repeat the automatic check closing totally the outlet again, continuously and try again the functioning. Verify if there is a no-return inlet valve on the pump and if it’s working good without loses. ELECTROIL IMMP1.1W – IMMP1.5W – IMMP1.5W-BC – IMTP1.5W – IMTP1.5W-BC – ITTP1.5W-BC - ENG... -
Page 16: Guarantee
The guarantee is excluded or interrupted in anticipation if the damage is caused to the following: External influences, non-professional installation, non-compliance with instructions, interventions by unauthorized locations, use of not original spare parts and normal wear. ELECTROIL IMMP1.1W – IMMP1.5W – IMMP1.5W-BC – IMTP1.5W – IMTP1.5W-BC – ITTP1.5W-BC - ENG... -
Page 17: Dichierazione Di Conformita' / Declaration Of Conformity
/ ALL INFORMATION HAVE BEEN WRITTEN AND CHECKED WITH THE GREATEST CARE. WE DO NOT TAKE ANY RESPONSIBILITY FOR ANY ERRORS OR OMISSIONS. ELECTROIL srl CAN AT ITS SOLE OPTION TO CHANGE AT ANY TIME THE CHARACTERISTICS OF THE PRODUCTS SOLD. MADE IN ITALY...
Need help?
Do you have a question about the Archimede IMMP1.1W and is the answer not in the manual?
Questions and answers