Sealey VSE6121.05.V2 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instructions protection
1. SAFETY
WARNING! Wear approved eye protection. Wear appropriate Personal Protective Equipment. A full range of Personal Protective
‰
Equipment is available from your Sealey stockist.
WARNING! Ensure that Health & Safety, Local Authority Regulations and general workshop practice Regulations are adhered to
‰
when using tools.
DO NOT use tools if damaged.
8
Maintain tools to ensure that they are in an adequate condition for safe use and optimum performance.
9
Ensure that a vehicle that has been raised by a jack is adequately supported. Use axle stands.
9
Wear suitable clothing to avoid snagging. DO NOT wear jewellery. Tie back long hair.
9
Account for all tools, parts and components being used. DO NOT leave tools in or near the engine. Return tools to suitable storage
9
after use.
IMPORTANT! These Instructions are provided as a guide only. Always refer to the vehicle manufacturer's service instructions or a
proprietary manual to establish the correct procedure and data.
WARNING! The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations. The
‰
Operator / user must apply caution and common sense (good practical sense).
When timing an engine, always prevent the engine from being turned over. Use a notice and/or inhibit the engine.
‰
WARNING! Incorrect or out of phase camshaft timing can result in contact between the valve head and the piston crown. This will
‰
cause damage to the engine.
2. INTRODUCTION
Crankshaft holding tool for BMW N47/N57 diesel engines. Essential for securing the crankshaft when replacing the timing chain.
3. APPLICATIONS
Make:
BMW
1 Series: E81/82/87/88: 116d (08-12), 118d (07-12), 123d
(07-14),120d (07-14)
1 Series: F22. 218d: (11-14), 220d (11-14), 225d (11-14)
3 Series: E90/91/92/93: 316d (07-12), 318d (07-14), 320d
(07-12), 325d (10-12), 330d (08-14)
5 Series: E60/61: 520d (07-10)
5 Series: F10/11: 525d (10-13), 530d (10-13), 530d xDrive
(11-15), 535d (10-13), 535d xDrive (11-15), M550d
xDrive (12-15)
5 Series: F07: 535dGT (09-15)
7 Series: F01/02/04: 730d (08-12), 740d (09-12), 750d xDrive
(12-15),
X1:E84: 18d sDrive (09-15), 20d sDrive (09-15), 18d xDrive
(09-15), 20d xDrive (09-15), 23d xDrive (09-12)
X3:E83: 2.0d (07-08), 18d xDrive (08-10)
X5:E70: 3.0d xDrive (10-13), 40d (10-13)
X6:E71/72: 3.0d xDrive (10-14), 40d xDrive (10-14)
© Jack Sealey Limited
CRANKSHAFT HOLDING TOOL -
BMW N47/N57 2.0, 3.0 - CHAIN DRIVE
VSE6121.05.V2
MODEL NO:
Model Numbers
Original Language Version
Engine codes
2.0D: N47: D20A, D20A/KO, D20B, D20B/T0, D20C,
D20O0, D20O1, D20U0, D20U1, D20K1
3.0D: N57: D30U0, D30O0, D30O1, D30T0, D30A, D30A/
O0, D30B, D30B/T1, D30C, D30C/S1, D30A0/O0,
D30A0A0/O1
VSE6121.05.V2 Issue 2 20/01/22