Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for peerless-AV PLAV70-UNLP-GB
Summary of Contents for peerless-AV PLAV70-UNLP-GB
- Page 1 Installation and Assembly - Universal Articulating Models: PLAV70-UNLP-GB, Swivel Double-Arm for 42" - 60" Plasma Screens PLAV70-UNLP-GS This product is UL Listed. It must be installed by a qualified professional installer. Maximum UL Load Capacity: 200 lb (91 kg)
-
Page 2: Wall Construction
NOTE: Read entire instruction sheet before you start installation and assembly. WARNING • Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call Peerless customer care at 1-800-865-2112. -
Page 3: Wall Mount Parts List
Wall Mount Parts List PLAV70- PLAV 70- Before you start make sure all parts UNLP-GB UNLP-GS listed are included with your product. DESCRIPTION QTY. PART # PART # A wall plate 201-P1040 201-C4040 B tilt-roll assembly 201-P1042 201-C4042 C arm assembly 201-P1044 201-C4044 D wall support arm axle... - Page 4 Before you begin, make sure all parts shown are included with your product. Adapter Bracket Parts List PLAV70-UNLP-GB PLAV70-UNLP-GS Description Part # Part # adapter bracket 201-P1110 201-C4110 shallow adapter bracket 201-P1514 201-C4514 deep adapter bracket 201-P1513 201-C4513 allen wrench...
-
Page 5: Installation To Wood Stud Wall
Installation to Wood Stud Wall WARNING • Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. • Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power. - Page 6 Installation to Concrete Wall WARNING • Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor. • Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
- Page 7 WARNING • If you are uncertain that product is properly installed, call customer care. Note: There are three mounting positions. The center position is shown right. Arm assemblies must be mounted with one mounting hole separating them. Slide washers (J) over wall support arm axles (D).
- Page 8 Attach two pieces of vinyl trim (E) to wall plate (A). Next, attach one piece of vinyl trim to bottom of swivel box on arm assembly (C). Insert one finishing cap (L) into each unused hole of wall plate (A). SWIVEL BOX Insert and tape carriage bolt (I) into top hole of tilt-roll assembly (B).
- Page 9 WARNING • Use an assistant or mechanical lifting equipment to safely lift and position the plasma TV. Insert two M10 screws (F) into swivel box on arm assembly (C) as shown. Leave approx. 1/4" of exposed thread. SWIVEL BOX .25" Hook tilt-roll assembly (B) onto M10 screws (F).
-
Page 10: Installing Adapter Brackets
Installing Adapter Brackets WARNING • Tighten screws so adapter brackets are firmly attached. Do not tighten with excessive force. Overtightening can cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque. •... - Page 11 For Flat Back Screen Refer to Screen Compatibility Chart to determine the proper fastener to use. Visit www.peerlessmounts.com/2 for a full screen compatibility chart for this mount. Begin with the shortest length screw, hand thread through multi-washer and adapter bracket into screen as shown below.
-
Page 12: Mounting And Removing Flat Panel Screen
Mounting and Removing Flat Panel Screen WARNING • Always use an assistant or mechanical lifting equipment to safely lift and position the plasma television. Refer to mount instruction sheet for attachment of adapter bracket to mount. Hook adapter brackets (BB or CC) onto adapter bracket (AA), then slowly swing screen in as shown. Turn screws clockwise at least six times to prevent screen from being removed as shown in detail 4. - Page 13 Depending on the specific size & weight of the plasma, If it is too difficult to adjust roll of plasma, loosen articulating swing arm may be angled at different screws shown in figure 9.1 using a phillips screw- positions, causing plasma to appear to lean sideways driver.