Advertisement
Quick Links
Setup controller parameters with buttons,such as driver chip type、controller numbere、
programs、playing speed、brightness of lamps;
The controller output have 2 SPI signal output port and 2 DMX512 signal output port.
Integration of multiple driving chip,change the IC type、clock frequency、duty cycle、
grayscale by softword setting.
Support environmental lighting control and audio control sensor module (optional) application,
adjust the brightness of lamps interactively.
Supports most serial driver LED driver chip.
SPECIFICATIONS
Model
T al le nt II
Colors
RGB three primary colors、RGBW four primary color、full-color display
Control points
Control 1024 pixels each port(DMX is 512 pixels)
Output port
Synchronous serial shift signal×2,compatible DMX512 signal×2
Gray scale
256 class—65536 class
Input Voltage
AC 12V/ DC 7.5V-24V/ DC 5V
Rated Power
2W
SD Card
4GB
Size
190.0mm×96.3mm×32.5mm
Interface
3Pin interface×5 4Pin interface×2
Tallent Front View
DMX512
serial signal
Synchronous
AC12V
signal output
output
signal
input
Power input
DC Power
Synchronous
Supply
signal output
Tallent Rear View
190MM
www.g2glight ing.com
Tallent Il Instruction
remote control
receiver
155A 10t h St Passaic,NJ07055
Talent I l Series
Tallent II Size
160MM
174.8MM
190MM
Tallent II Button control panel
MENU
MU
MU
OK
OK
OK
Tallent II Remote control button definition
Play and Pause
MENU
+
Set Menu
TEST
Self Test
-
0
C
1
2
3
Exit Setup
4
5
6
7
8
9
Numeric Key
Phone:(973)575-2600
Fax:(973)575-2603
84.3MM
Add key
Key reduction
Confirm and save
Plus
Minus
Previous fragment
Next fragment
Advertisement
Summary of Contents for G2glighting Talent II Series
- Page 1 Talent I l Series Tallent Il Instruction Setup controller parameters with buttons,such as driver chip type、controller numbere、 programs、playing speed、brightness of lamps; The controller output have 2 SPI signal output port and 2 DMX512 signal output port. Integration of multiple driving chip,change the IC type、clock frequency、duty cycle、 grayscale by softword setting.
- Page 2 Talent I l Series Controller keys and display instructions 一、LCD main screen after boot Controller name Controller name MR- 502 MR- 502 NO CARD No SD Card State NO Files No files in SD Card Controller name ID=001 PLAY 001 Currently playing program fragment number 二、Controller parameters setting 1、...
- Page 3 Talent II Series Brightness BRIGHT =100% Brightness percentage Press ,set brightness,Press to save 6、Brightness of the four channels Adjustment Press again to enter Brightness of the four channels adjustment settings interface. As figure below: A channel brightness B channel brightness...
- Page 4 Talent Il Series 11、Self Test Setting On the working state ,Press again to enter self test setting interface. As figure below: Self Test -TEST- -TEST- Self Test LINE0018 grating test 2 RED Red Self Test Self Test -TEST- -TEST- Self Test 3 GREEN Green Self Test 4 BLUE...
- Page 5 Talent Il Series 2、 Play mode Press ,enter the play mode selection interface,as shown below: INDEX INDEX play mode play mode =Loop =Wait Loop mode Wait mode INDEX play mode fragment Loop play mode Press ,select Loop mode、Wait mode and fragment Loop play mode ,Press to save the option.
- Page 6 Talent Il Series 8、Setting driver chip type Press again,to enter driver chip type settings interface. As figure below: driver chip type Chip Sel= NO Chip Select your driver chip Press to select your own driver chip type ,press to save. 9、Remote control adjustment Press again,to enter Remote control settings interface.
Need help?
Do you have a question about the Talent II Series and is the answer not in the manual?
Questions and answers