Related Manuals for Parker BD15 Series
Summary of Contents for Parker BD15 Series
- Page 1 Bulletin HY14-1450-M1/US Installation and Service Guide Series BD15 and BD30 Flow Control Servovalves Effective: October 15, 2006 Supersedes: Catalog No. 1450 ISM, dated 3/96...
-
Page 2: Table Of Contents
Offer of Sale The items described in this document are hereby offered for sale by Parker Hannifin Corporation, its subsidiaries or its authorized distributors. This offer and its acceptance are governed by the provisions stated in the "Offer of Sale". -
Page 3: Technical Information
When used in conjunction with Series BD90/95 and BD101 servo amplifiers or a motion controller, Series BD valves will provide accurate control of rotary and linear actuators. 17/15/12 Bul 1450-M1pgs.p65, dd Parker Hannifin Corporation Hydraulic Valve Division Elyria, Ohio, USA... -
Page 4: Dimensions
2. Servovalve mounting screws are to be torqued to for details. 110-150 in.-lbs., above run down torque. 3. For proper orifice selection and decal part number, refer to Table 1. Bul 1450-M1pgs.p65, dd Parker Hannifin Corporation Hydraulic Valve Division Elyria, Ohio, USA... - Page 5 2. Servovalve mounting screws are to be torqued to 110-150 in.-lbs., above run down torque. 3. For proper orifice selection and decal part number, refer to Table 1. Bul 1450-M1pgs.p65, dd Parker Hannifin Corporation Hydraulic Valve Division Elyria, Ohio, USA...
- Page 6 2. Servovalve mounting screws are to be torqued to 110-150 in.-lbs., above run down torque. 3. For proper orifice selection and decal part number, refer to Table 1. Bul 1450-M1pgs.p65, dd Parker Hannifin Corporation Hydraulic Valve Division Elyria, Ohio, USA...
-
Page 7: Series Bd30
2. Servovalve mounting screws are to be torqued to for details. 110-150 in.-lbs., above run down torque. 3. For proper orifice selection and decal part number, refer to Table 1. Bul 1450-M1pgs.p65, dd Parker Hannifin Corporation Hydraulic Valve Division Elyria, Ohio, USA... - Page 8 2. Servovalve mounting screws are to be torqued to 110-150 in.-lbs., above run down torque. 3. For proper orifice selection and decal part number, refer to Table 1. Bul 1450-M1pgs.p65, dd Parker Hannifin Corporation Hydraulic Valve Division Elyria, Ohio, USA...
- Page 9 2. Servovalve mounting screws are to be torqued to 110-150 in.-lbs., above run down torque. 3. For proper orifice selection and decal part number, refer to Table 1. Bul 1450-M1pgs.p65, dd Parker Hannifin Corporation Hydraulic Valve Division Elyria, Ohio, USA...
-
Page 10: Series Bd15
The Parker BD series servovalves are ruggedly Flow, proportional to the input electrical current, is then designed for use in the industrial market place. From metered out the C2 port. - Page 11 10. Install servovalve on the mounting pad. Refer to BD Series servovalves. pages 2 and 5 as required for installation. Except for orifice changing and filter removal, cleaning Bul 1450-M1pgs.p65, dd Parker Hannifin Corporation Hydraulic Valve Division Elyria, Ohio, USA...
-
Page 12: Service Information
Fluorocarbon O-ring kits are also available; Order Part Number 810013-XX. ** This Part Number is a blank with no hole. It is used when an external pilot fluid source is supplied to the test port. Bul 1450-M1pgs.p65, dd Parker Hannifin Corporation Hydraulic Valve Division Elyria, Ohio, USA... -
Page 13: Ordering Information
Intrinsically Safe Class I, II and III, Division 1 (Standard connector over C + to B = P to C flow). Groups A through G. Refer to Parker Bulletin 1452. B = Connector over Port C + to Pin B = P to C flow. -
Page 14: Troubleshooting
2. Partially plugged orifice or filter. 2. Check pilot pressure at test port and/or remove, inspect, and clean orifice/filter per Servovalve Maintenance Section. 3. Sticky spool. 3. Return valve to factory. Bul 1450-M1pgs.p65, dd Parker Hannifin Corporation Hydraulic Valve Division Elyria, Ohio, USA... -
Page 15: Offer Of Sale
The items described in this document and other documents or descriptions provided by Parker Hannifin Corporation, its subsidiaries and its authorized distributors are hereby offered for sale at prices to be established by Parker Hannifin Corporation, its subsidiaries and its authorized distributors. This offer and its acceptance by any customer ("Buyer") shall be governed by all of the following Terms and Conditions. - Page 16 Parker Hannifin Corporation Bulletin HY14-1450-M1/US, 10/06, 2M, PHD Hydraulic Valve Division 520 Ternes Avenue Elyria, Ohio, USA 44035 Tel: (440) 366-5200 Fax: (440) 366-5253 www.parker.com/hydraulicvalve...
Need help?
Do you have a question about the BD15 Series and is the answer not in the manual?
Questions and answers