Sinotimer TM-610 Quick Start Manual

TM-610
Digital time switch for DIN rail
SINOTIMER
3. Wiring diagrams
L
L
N
ok
Menu Menu
_
Res
+
External
E X T
1 Switch
2 3
Load
N
L
L1
4. Setting and operating
Notes:
1. Press "Menu" and "-" for 3 seconds, procedures will be closed but all
former setting will be lost; press "Res", all procedures will be cleared.
2. In any setting screen but no any operation within 30 seconds,
procedure will back to clock screen automatically, and will not save
setting data.
3. Duing to built-in lithium battery, you can install timer in distribution
box or control circuit after setting procedures.
www.sinotimer.com
N
ok
_
Res
+
E X T
1
2 3
max18.0
max66.0
TM-610
1. Introduce
-Industry first utility function:
Built-in calendar, 10 holiday times can be set in a year
EXT port(extended length can reach 100 meters)
16 groups procedure controls(ON/OFF)
32 pulse controls(can be used for bell or on trigger-start equipment)
Countdown function
-Can be programmed, or manually controlled for easy use
-Imported digital chip, intelligent and stable system
-LCD display, LED work instruction
-Built-in lithium battery, when a power failure, data will not be lost and timer
will travel time as usual and be in auto-sleep
-Key parts adopt imported components
-Standard width: 17.5mm
-Standard installation with Din 35mm
-Widely used in industry, house, building, corollary equipment, etc.
2. Technical data
Rated voltage:
Mains frequency:
Procedure setting:
Pulse program:
Holiday program:
Countdown:
Electrical life:
Mechanical life:
Power reserve:
Power:
2
TM-610 TM-610
Program setting interface chart
Unit:mm
Press "Menu" Key to select
Press OK again to enter the clock setting
Auto
EXT
2
Clock set 4 state control
interface settings interface
Auto on/on
Auto oFF/oFF
Date and time setting built-in calendar, set Year, Mouth, Hour and
Minute respectively.
1. Press "Menu" until "
Mark Year will flash.
2. Press"+/-" to required year ,then press "OK" to confirm .About setting mouth,
day ,hour and minute ,same operation as setting year.
3. After finishing setting date and time, press "Menu" to exit and complete this
setting.
Note: After the date is set, week will be self-synchronizing
3 4
load capacity:
220-240VAC
50Hz Load Inductive :
16 on/off program
EXT switch:
3 2 c h a n n e l s Contact point:
duration:1-99sec
10 Contact resistance
between contacts:
duration: Insulation resistance
1-99min 59sec between contacts:
Working temperature:
5
10 times
7 Ambient humidity:
10 times
Storage temperature:
3Years
Weight:
≤ 3VA
After press Res Key
Initial interface
!
prog
*
Cannot be used at the same time
*
Press +/- key select
press OK again enter countdown setting
*
Press "OK" Key
Press +/- key select
press OK again enter pulse setting
Auto
Press +/- key select prog
press OK again enter program setting
*
6
Press +/- key to select "Man"
press OK again enter funtion setting
Cock Auto
EXT
interface
6
Auto
EXT
6 6
EXT:External control Holiday 16 program
settings interface settings interface setting interface
" flashes, then press "OK" into clock setting interface,
SINOTIMER
AC250V 16A COSφ=1
AC250V 10A COSφ=0.6
cable length≤100m
1group
≤100mΩ
≥100MΩ
-10 ~ +50 C O
35-85% RH
-10 ~ +60 C O
≤ 90g
www.sinotimer.com
SINOTIMER
1 2 3
Auto Auto
6 6
32 pulse Countdown
setting interface setting interface
www.sinotimer.com