CTS CVT-3002-PLUS Series - Media Converter User Guide
- User manual (2 pages) ,
- User manual (2 pages) ,
- User manual (2 pages)
Advertisement
Checklist
The package should contain the following items:
- CVT-3002-PLUS Converter
- AC-DC Power Adapter
- User's Guide
Please notify your sales representative immediately if any items are missing or damaged.
Overview
CVT-3002-PLUS is designed to meet the massive needs for Gigabit network deployment and able to extend a copper based Gigabit network via fiber cable to a maximum distance up to 80KM.
CVT-3002-PLUS is fully compliant with IEEE802.3, 802.3u, 802.3ab & 802.3z standards. It can be installed into a CVT Converter RACK. The installation & operation procedures are simple & straightforward. Operation status can be locally monitored through a set of Diagnostic LED located in the front panel.
Major Features:
- Auto-Negotiation in TX port
- MDI/MDIX Auto-Crossover supported
- Support Flow Control
- Support Link Alarm
- Support Jumbo Frame 9K bytes (under 10,100,1000Mbps)
- Store and Forward Switching Mechanism
- Support Auto & Force mode configuration
Installation
 | Attach fiber cable from the CVT-3002-PLUS to the fiber network. The fiber connections must be matched – transmit socket to receive socket. |
 | Attach a UTP cable from the 10/100/1000BASE-T network to the RJ-45 port on the CVT-3002-PLUS. |
 | Connect the power adapter to the CVT-3002-PLUS and check that the Power LED lights up. The TX Link/Act and F/O Link/Act LEDs will light up when all the cable connections are satisfactory. |
Figure 1. CVT-3002-PLUS dual fiber Front Panel
Figure 2. CVT-3002-PLUS WDM & SFP Front Panel
Figure 3. CVT-3002-PLUS Converter Rear Panel
DIP SWITCH Setting
The default setting for PIN 1 and 6 is ON. The rest of Pins are OFF.
| Pin NO. | Function | OFF | ON |
| 1 | TP Auto-Negotiation | Disable | Enable |
| 2 | Manual TP speed | 10M | 100M |
| 3 | Manual TP speed | N/A | 1000M |
| 4 | Duplex mode | Half | Full |
| 5 | Flow Control | Disable | Enable |
| 6 | F/O mode | Force | Auto |
| 7 | Link Alarm | Disable | Enable |
| 8 | Reserved | - | - |
NOTE:
- Before changing TP speed, duplex mode and flow control setting, please make sure PIN 1 is set to OFF.
- When TP speed is set to 10M or 100M manually, PIN 3 needs to be turned OFF.
- Under 1000Mbps, it supports full-duplex mode only.
LED Description
| LED | Color | Function |
| Power | Green | Lit when power is available. |
| TX Link/Act | Green | Lit when TX cable connection with remote device is good. Blink when TX traffic is present. |
| FO Link/Act | Green | Lit when Fiber cable connection with remote device is good. Blink when F/O traffic is present. |
| FDX | Green | Lit when TX works in Full-Duplex. Not-Lit when TX works in Half-Duplex. |
| Speed | Green | No-Lit when TX works in 10M. Lit when TX works in 100M. |
| Orange | Lit when TX works in 1000M. | |
| Status | Green | Lit when TX and F/O link is up. |
| Orange | Lit when TX or F/O link is down. |
Technical Specifications
| Standards | IEEE 802.3, 802.3u, 802.3ab, 802.3z | |
| Interface | 1 X 10/100/1000 RJ-45 connector 1 X 1000 F/O port or SFP Slot | |
| LED | Power, FDX, Status, Speed, FO Link/ACT, TX Link/ACT | |
| Power | I/P AC 100-240V O/P DC 5V | |
| Power Consumption | 2.2W | |
| Weight | 0.6KG | |
| Dimensions | 71mm(W)X94mm(D)X26mm(H) | |
| Temperature | Operating: 0o~50oC Storage: -20o~60oC | |
| Humidity | 5%~90% RH non-condensing | |
| Certification | FCC/CE Class A | |
| Media | TP: | EIA/TIA-568 CAT 5e, 1000M |
| Fiber: | 50/125 or 62.5/125m multi-mode 9/125 or 10/125m single-mode | |
| * Please contact us for further reports and updates. | ||
NOTE: Specifications may change without prior notice.
Fiber Transceiver Information
Dual Rate
2 Wave-Length WDM
| TYPE | W2A(SM-10) | W2B(SM-10) |
| Connector Type | SC | SC |
| Wavelength | 1310/1550nm | 1550/1310nm |
| Typical Distance | 10 Km | 10 Km |
| Min TX PWR | -10.0dBm | -10.0dBm |
| Max TX PWR | -3.0dBm | -3.0dBm |
| Sensitivity | -20.0dBm | -20.0dBm |
| Link Budget | 10.0dB | 10.0dB |
1000M
Multi-Mode/Single-Mode
| TYPE | BTFC | BTFC (SM-10) | BTFC (SM-20) | BTFC (SM-30) | BTFC (SM-50) | BTFC (SM-80) |
| Connector Type | SC | SC | SC | SC | SC | SC |
| Wavelength | 850nm | 1310nm | 1310nm | 1310nm | 1550nm | 1550nm |
| Typical Distance | 550m | 10 Km | 20 Km | 30 Km | 50 Km | 80 Km |
| Min TX PWR | -9.5dBm | -9.5dBm | -9.0dBm | -5.0dBm | -5.0dBm | 0dBm |
| Max TX PWR | -1.5dBm | -3.0dBm | -2.0dBm | 3.0dBm | 3.0dBm | 5.0dBm |
| Sensitivity | -17.0dBm | -20.0dBm | -23.0dBm | -24.0dBm | -24.0dBm | -24.0dBm |
| Link Budget | 7.5dB | 10.5dB | 14.0dB | 19.0dB | 19.0dB | 24.0dB |
2 Wave-Length WDM
| TYPE | W2A (SM-10) | W2B (SM-10) | W2A (SM-20) | W2B (SM-20) | W2A (SM-40) | W2B (SM-40) |
| Connector Type | SC | SC | SC | SC | SC | SC |
| TX Wavelength | 1310nm | 1550nm | 1310nm | 1550nm | 1310nm | 1550nm |
| RX Wavelength | 1550nm | 1310nm | 1550nm | 1310nm | 1550nm | 1310nm |
| Typical Distance | 10 Km | 10 Km | 20 Km | 20 Km | 40 Km | 40 Km |
| Min TX PWR | -10.0dBm | -10.0dBm | -9.0dBm | -9.0dBm | -5.0dBm | -5.0dBm |
| Max TX PWR | -3.0dBm | -3.0dBm | 0 dBm | 0 dBm | 3.0dBm | 3.0dBm |
| Sensitivity | -22.0dBm | -22.0dBm | -23.0dBm | -23.0dBm | -23.0dBm | -23.0dBm |
| Link Budget | 12.0dB | 12.0dB | 14.0dB | 14.0dB | 18.0dB | 18.0dB |
NOTE: Specifications may be changed without prior notice.
Contact Information
Connection Technology Systems INC (CTS)
18F-6, No.79, Sec.1, Xintai 5th Rd., Xizhi Dist.,
New Taipei City 221, TAIWAN, R.O.C.
TEL: +886 2 26989661 FAX: +886 2 26989662
E-Mail: info@ctsystem.com
Documents / ResourcesDownload manual
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download CTS CVT-3002-PLUS Series - Media Converter User Guide
Advertisement
Need help?
Do you have a question about the CVT-3002-PLUS Series and is the answer not in the manual?
Questions and answers