Sanyo DAS201 Owner's Instruction Manual page 6

OPERATING INSTRUCTIONS CONT'D
K. Playing All Messages
– The LED will display the total number of messages in the DAS 201's
memory. The following details the playback procedures:
• Playback
• Pause Message
• Resume Playback from Pause
• Repeat Message
• Erase Single Message
• Stop Playback
• Erase and Save ALL Messages
L. Call Screen
– The DAS 201 can be used to screen incoming calls. Simply set the unit to
Answer mode by pressing the 'ANSWER' key. When an incoming call
occurs, adjust the volume control so that you can hear the incoming caller
leaving their message. If you wish to speak to the caller, simply pick up the
receiver. The DAS 201 will automatically stop recording.
M. Remote Control Security Code
– The Security Code is set to a factory default of '159'. This code can be
changed to any number between 000 and 999. To change your security
code perform the following steps:
• Press the FF key for approximately 2 seconds and release to display
the current security code. The DAS 201 will then display the first digit of
the security code. Use the FF
decrease the number of the first digit. Once you have arrived at the
desired number, press the 'ANSWER' key to confirm your selection.
• Repeat the process for the second and third digits.
• If no key is pressed within 8 seconds, the setup procedure will
be aborted.
• When complete, press the 'STOP/TIME' key to conclude the procedure.
Press 'PLAY'
Press 'PLAY'
Any one of the following
keys will resume Playback:
PLAY/FF /REPT /
ERASE/STOP
Press 'REPT 'once to replay
current message, twice to
replay the previous message.
Press 'ERASE'
Press 'STOP/TIME'
Press and hold 'ERASE' for
about 2 seconds. A long beep
will sound, and ALL messages
will be erased. To RESTORE all
messages, Press and hold
'ERASE' again for about 2
seconds. A long beep will sound
and messages will be restored.
and the REPT to increase or
10
OPERATING INSTRUCTIONS CONT'D
N. Call Breakthrough (CBT)
– The DAS 201 is equipped to alert you to an Urgent call. With CBT, incom-
ing callers who know your CBT code will have the ability to bypass the
Outgoing message and cause the DAS 201 to sound a short alarm. This is
designed to alert you to an Urgent call, if you are home screening your calls.
The CBT code has a factory default of '267'. This code can be changed to
a
number between 000 and 999. To change your CBT code perform the
following steps:
• Press the REPT key for approximately 2 seconds and release to
display the current CBT code. The DAS 201 will then display the
first digit of the CBT code. Use the FF
increase or decrease the number of the first digit. Once you have arrived
at the desired number, press the 'ANSWER' key to confirm your selection.
• Repeat the process for the second and third digits.
• If no key is pressed within 8 seconds, the setup procedure will
be aborted.
• When complete, press the 'STOP/TIME' key to conclude the procedure.
O. Remote Control Function Operation
– The DAS 201 allows you to perform many of its functions from a remote
telephone. To perform these remote functions, just follow these
simple steps:
• Call the Answering Machine.
• When the machine answers press ' * ' to skip the OGM. A long beep
will sound.
• Enter the security code (factory default '159') to enter the Remote Control
Mode.
• Enter the key combination for the desired function as per the
following table:
KEY(S)
Skip OGM Play
*
1 Play OGM1
2 Play OGM2
3 Room Monitoring (listens to room DAS 201 is in)
4 Repeat or Play Memos
5 Play All Messages or Pause/Play
6 Forward or Play New Messages
7 Erase Individual Messages
8 Stop or Save All Messages
9 Set to Answering Machine OFF Mode
n
and the REPT
REMOTE FUNCTION
11
y
keys to