Sanyo VWM-950 Quick Start Manual

Video Cassette Recorder
VWM-950
Thank you for buying Sanyo.
This guide will enable the quick and easy setup of your new VCR,
simply follow the procedures inside.
For further details of features, please refer to the instruction manual.
Is Everything In The Box?
• Remote control • RF cable
(NA323)
with two AA batteries
1
Connecting
DEW CAUTION
Condensation can form inside the VCR when it is suddenly moved from a cold place to a warm or
humid environment. In any such circumstance do not use this unit approximately 2 hours allowing
complete elimination of any condensation.
Rear of TV
ANTENNA
INPUT
R
AUDIO IN
L
VIDEO IN
ANTENNA
INPUT
R
AUDIO IN
L
VIDEO IN
(not supplied)
Rear of VCR
Printed in China
• Instruction • Quick
manual start guide
Quick start guide
RF Cable
Audio Cable
(not supplied)
Video Cable
ANT
AUDIO
IN
L
OUT IN
R
VIDEO
OUT
OUT IN
81VMN20402--- / HJ420UD #####
2
Setting the RF Output Channel and Initial Programming
Setting the RF output channel
If channel 3 is already occupied for broadcasting,
1 Set your TV to channel 4.
2
Insert a pre-recorded tape into this unit.
3 Press [PLAY B] once to start playback.
4
After a few seconds, press [PLAY B] on the unit
for 3 seconds.
• The RF output channel will change to channel 4
from channel 3 and you will see a playback
picture.
• When a picture does not appear on the TV screen,
repeat step 4).
5
Press [C STOP] to stop playback.
3

Setting the Clock

1 Press [MENU] and the MAIN
menu will appear.
• If the clock is not set, the
Antenna
"CLOCK SET" screen appears
when you press [MENU]. In this
case, go to step 3).
2 Press [C C STOP] or [PLAY B B ] to
select the "CLOCK SET" menu.
Press [F.FWD g g ] and the
"CLOCK SET" menu will appear.
3 Press [C C STOP] or [PLAY B B ] to
select the month. Press
[F.FWD g g ].
RF Cable
4
Press [C C STOP] or [PLAY B B ] to
select the day. Press [F.FWD g
Initial Programming
1
Press [POWER] and the
language menu will appear.
2 Press [C C STOP] or [PLAY B B ] to
select language for the VCR
on-screen display. Then press
[F.FWD g g ].
3
Press [F.FWD g g ] again to begin
channel programming. "AUTO
SET UP" will flash.
4 Please wait for a few minutes.
After scanning, the tuner stops on the lowest
memorized channel.
• For details, refer to the Instruction Manual.
Inserting the Batteries
Your REMOTE CONTROL
HANDSET is powered by two
AA type batteries.
1
To insert them, push the tab
backwards and lift off the
cover of the handset.
2
Put the two batteries into the compartment mak-
ing sure the + and – are correctly positioned.
3 Replace the cover.
5 Press [C C STOP] or [PLAY B B ] to
- M E N U -
select the year. Press [F.FWD g
B TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
6
Press [C C STOP] or [PLAY B B ] to
CLOCK SET
LANGUAGE SELECT
AUDIO OUT select the hour. Press [F.FWD g
TV STEREO [ON]
SAP
7 Press [C C STOP] or [PLAY B B ]
to select the minute. Press
- M E N U -
[F.FWD g g ].
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
8
B CLOCK SET Press [C C STOP] or [PLAY B B ] to
LANGUAGE SELECT
AUDIO OUT select the "AM" or "PM".
TV STEREO [ON]
SAP
9 Press [F.FWD g g ] when finished.
CLOCK SET
MONTH DAY YEAR
1 0 / – – – – – –
HOUR MINUTE AM/PM
– – : – – – –
g ].
Weekdays 7:30 AM – 4:00 PM Central Time
LANGUAGE SELECT
B ENGLISH [ON]
FRANCAIS
ESPAÑOL
CH 01
AUTO SET UP
CLOCK SET
MONTH DAY YEAR
g ].
1 0 / 0 3 2 0 0 5
HOUR MINUTE AM/PM
– – : – – – –
g ].
CLOCK SET
MONTH DAY YEAR
1 0 / 0 3 MON 2 0 0 5
HOUR MINUTE AM/PM
0 5 : 4 0 P M AM
B PM
Need help? Call
1-800-813-3435