Sealey SA671.V3 Instructions

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used
according to these instructions and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE
THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
! Follow all workshop Health & Safety rules, regulations, and conditions when using tool.
" " WARNING! Disconnect from air supply before changing grinding bit or servicing.
! Maintain die grinder in good condition and replace any damaged or worn parts. Use genuine parts only.
Unauthorised parts may be dangerous and will invalidate the warranty.
" " WARNING! Check correct air pressure is maintained and not exceeded. We recommend 90psi.
! Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that
all connections are secure.
" " WARNING! Before each use check grinding bit is secure, and the bit is not worn or damaged, if damaged,
replace immediately.
! Ensure replacement grinding bits are not damaged (cracks, deformations or splinters etc).
! Always use the correct grinding bit suitable for the material being ground. Ensure the maximum speed
specification of the bit is higher than that indicated on the machine data plate.
" " WARNING! Always wear approved eye or face protection when operating the
! Use breathing protection in accordance with COSHH regulations if fumes or dust pose a hazard.
! Wear ear defenders and safety gloves.
! Keep hands and body clear of the workpiece when operating the
! Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
! Secure unstable workpiece with a clamp, vice or other adequate holding device.
! Keep children and non essential persons away from the working area.
! Avoid subjecting grinding bit to excessive strain, always ease grinding bit against workpiece (a harsh impact
may break the bit). Maintain a controlled progression.
# DO NOT get the die grinder wet or use in damp or wet locations.
# DO NOT hold the workpiece by hand. Use clamps or a vice to secure the workpiece.
# DO NOT use the die grinder for a task it is not designed to perform.
" " WARNING! DO NOT use die grinder if damaged or faulty. Contact your local service agent.
# DO NOT use die grinder unless you have been instructed in its use by a qualified person.
# DO NOT carry the die grinder by the air hose, or yank the hose from the air supply.
# DO NOT direct air from the air hose at yourself or others.
" " WARNING! DO NOT grind any materials containing asbestos.
# DO NOT turn the die grinder on whilst the grinding bit
# DO NOT use die grinder where there are flammable liquids, solids or gases such as paint solvents, including
waste wiping or cleaning rags etc. as generated sparks may be dangerous.
# DO NOT touch the workpiece close to the ground surface as it will be very hot. Allow to cool. The workpiece
may also be very sharp.
# DO NOT operate die grinder if you are tired or under the influence of alcohol, drugs or intoxicating medication.
! When not in use disconnect from air supply and store in a safe, dry, childproof location.
Risk of Hand Arm Vibration Injury
Die Grinder Model No.'s SA67.V3 & SA671.V3 when operated in accordance with these instructions and tested
in accordance with EN 28662-2: 1994 results in the following vibration emission declared in accordance with
BS EN12096: 1996.
Measured vibration emission value: . . . . . . . . . . .3.4m/s²
These values are suitable for comparison with emission levels of other tools that have been subject to
the same test.
This tool may cause hand-arm vibration syndrome if its use is inadequately managed.
Recommended Measures to reduce risk of hand-arm vibration syndrome:
This item represents a low Hand Arm Vibration risk to users. The calculated minimum usage period exceeds 8
hours. We recommend appropriate safety equipment is utilised and regular breaks for the operator are
employed to reduce any residual risk of fatigue or repetitive strain injury.
INSTRUCTIONS FOR:
DIE GRINDER
SA67.V3 &
Models:
SA671.V3
die grinder.
die grinder.
is in contact with the work piece.
Uncertainty: . . . . .1.4m/s²
SA67.V3, SA671.V3 - 2 - 100807