Yeacomm YF-P11 - LTE Wireless Terminal Manual

Also See for YF-P11:

User manual (2 pages)

Table of Contents

Contents

1 Main Technology Parameters
2 Installation
3 About Terminal
4 Access internet
5 Router setting
6 Documents / Resources
- 6.1 Download manual

Yeacomm YF-P11 - LTE Wireless Terminal Manual

Main Technology Parameters

Working temps: -30℃ -- +60℃
Relative humidity: 5%--95%S
Working frequency could be customized.
Frequency: FDD: B1/B2/B3/B5/B7/B8/B12/B17/B20, B4/B28 (Optional)
TDD Band 38/39/40/41, B42/B43(optional)
WCDMA: 900/2100Mhz, 850/900/1900/2100Mhz(Optional)
GSM: 850/900/1800/1900Mhz
Frequency can be customized according to your requirements
Power supply: input AC:100V~240V,50Hz~60Hz Output DC: 15V, 500mA
Rate of uplink and downlink:
LTE(Category 4): DL 150Mb/s; UL 50Mb/s

Installation

Picture shows below. When you hear a "click" sound, it means that the USIM card has been installed successfully.
Use Cate5e cable to connect the POE's CPE port and outdoor router LAN port.
placed the set outside at open space, the front direction toward the base station and fixed well.
Use POE Power supply connect External power outlet, the system will automatically power on after connected, about 1~2 minutes.

warning Attention:

Please do not insert USIM card when connecting with the external power supply
Please do not contact with the mental surface when removing the USIM card, it will damage the card.
Please use the original standard power adapter.

About Terminal

The terminal can work under the LTE network, only supports data and SMS service and doesn't support voice business.

Equipment connection diagram
1. interface introduction

Port type	Port function	Remarks
SIM	Install USIM card interface, please follow the instructions install USIM card, stick the waterproof stickers after installed card	Please do not insert or take out the SIM card when the power on.
LAN	Ethernet port, Use to connect router WAN/POE port	PC and outdoor router should use Cate5 connect, and the distance should within 50 meters.

Indicator

Type	Status	Description
RF	All off	no signal (the signal status can be checked by terminal configuration page)
	One on	The signal is poor
	Two on	Signal is moderate
	Three on	Signal is good
	All on	Signal is very good
SYS	Off	Power abnormal, the router power off
	On	Power normal, the router power on
SIM	Off	No SIM or Can not read SIM
	On	Terminal read the SIM normally
ETH	Off	Terminal doesn't link with PC
	On	Terminal have link with PC
RUN	Off	Terminal is doesn't running
	On	Terminal is running

Access internet

The router support standard internet cable to connect computer, do not need any driver; Support Windows XP, Windows 7,Windows 8,MAC OS, Linux, Android and so on; Please confirm the set has been installed well ad the manual before access the internet.

Access PC
The router support standard internet cable to connect computer, No matter what way to connect, please make sure to set the mode: obtain IP address as automatically.
Access terminal
Please enter"192.168.0.1" in the IE browser after the computer obtain the IP address. Then input the "user name" and "password" to access the router configuration page. Default "user name" and "password"both are admin.

Log into the device configuration page below browsers are recommended:

at least IE 7.0
at least Safari 4.0
at least Chrome 10.0
at least Firefox 3.0
at least Opera 10.0

Router setting

Please make sure that the router is in normal running and is connected with the computer when configure router. A part of the configure parameters have to set under operators advise, if take the error parameters, the internet would be out of service. Long press "reset" button restore to factory settings.

Menu 1	Menu 2	Description
System status	Home gateway information status	You can check the router running status info, such as running hours, LTE network info, SIM info, WAN, LAN info, WLAN info and so on.
	Online terminal status	Check the user's info who has connected with the terminal, including MAC address, IP address and so on
	Traffic Statistics	Check all the traffic status since the first running time, specific traffic information is according to the operator's data.
	Version info	Check the router's software and hardware version number.
	LTE info	Check LTE details info, including frequency, cell, RSRP, SINR, RSRQ etc.
Device Setting	WAN Setting	Network selection: wireless network and PLMN mode optional User can select 4G/3G/2G networks. 4G is the fastest, 3G medium, 2G slowest. If in multiple selection can set the priority network, the router could register to the priority network once it is the fastest. Default setting is in multiple selections, 4G preferred. PLMN is the default setting. User can activated manual option if necessary. Manual option needs searching the available PLMN in advance. IPV4 / IPV6: Set router IP stack support model. The default setting is IPV4 / IPV6 dual stack. APN: Set the access name when you dial. The setting needs follow operator's requirement, any change may lead to being unable to access to the internet. Not recommend changing it. PIN code: Set USIM card PIN1 and PUK. If the USIM card enable PINI code or PUK code, then you need to fill in the appropriate PINI code. Otherwise, the router will not dial. MTU: Set the MTU parameters of the router network port. Do not recommend to change, otherwise it will cause abnormal network. It needs professional selection DNS setting :set the DNS server address.
	WLAN Setting	WLAN setting: Turn on/off function of WIFI, view / change WIFI SSID, password, encryption, channel etc. User can modify router WIFI SSID, password and encryption methods. It takes the current channel in use. Channel could be modified.
	DHCP	DHCP: Set the router's DHCP info and IP info, once turn off the DHCP, the user has to set IP manually, and it can not obtain the IP automatically. Keep address: Reserved address is only effective when you enable DHCP server, click [Add] button to formulate MAC address binding fixed IP address, this IP address will only be assigned to the MAC address which the computer belongs.
	IPV6 set	Setting IPV6 address allocation, PNAT function.
SMS function	New message	You can edit new message and send it
	In box	Check received message
	Draft	Check edited but not send message
	Sent	Check the message sent message
Firewall	Filtering Rules	Ports filtering: Set the ports which need to be filtered IP address filtering: Set the IP address which need to be filtered. MAC address filtering:Set the MAC address which needs to be filtered. URL Filtering: Set the website which needs to be filtered. MAC binding: Set binding IP and MAC address. Default rules: Set other filtering rules which has not included here.
Firewall	Speed limit	Setting speed limit rule, only IP address limit currently
System manage ment	System setting	Change Password: Change password logging into the router configuration page. Change user name: change the log on user name. Reboot setting: reboot setting. System Time: Set the router system time.
	System log	Check system work log
	Reboot	Support reset router
	System update	When the system update, you must download the updated file to your computer. The device supports tar.gz or tar.lzma format update file, you need to unzip the file. After the computer has obtained the upgrade files, update files need to upload to the device first, meanwhile also need to upload MD5 verification code during the upgrade. After uploading, you can click to upgrade system. The system upgrade will not remove your previous profile
	Module update	Update the LTE module software
	Configurable update	Update router system setting
	Restart device	User can restart router
	Online help	View self-help files for router