Advertisement
We recommend that an RCD (Residual Current Device) is used with all electrical products. It is particularly important
to use an RCD with portable products that are plugged into a supply not protected by an RCCB. If in doubt consult
a qualified electrician. You may obtain an RCD by contacting your dealer. You must also read and understand the
following instructions concerning electrical safety.
1.3.1. The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises,
to be tested by a qualified person, using a Portable Appliance Tester (PAT), at least once a year.
1.3.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe
condition of the appliance and the safety of the appliance operator. If in any doubt about electrical
safety, contact a qualified electrician.
1.3.3. DO ensure that the insulation on all cables and the product itself is safe before connecting to the mains
power supply. See 1.3.1. above and use a Portable Appliance Tester (PAT).
1.3.4. DO ensure that cables are protected against short circuit
and overload.
1.3.5. DO regularly inspect power supply leads, plugs and sockets
for wear, damage or loose connections.
1.3.6. DO check that the voltage marked on the product is the
same as the power supply to be used and check that all
fused plugs are fitted with the correct capacity fuses.
1.3.7. DO NOT pull or carry the charger by the lead.
1.3.8. DO NOT pull the plug from the socket by the lead.
1.3.9. DO NOT use worn or damaged cables, plugs or connectors.
Immediately have any faulty item repaired or replaced by
a qualified electrician. When a BS 1363/A UK 3 pin plug is
damaged, cut the cable just above the plug and dispose
of the plug safely.
Fit a new plug according to the following instructions (UK only). The charger is double insulated and there
is no earth core.
a) Connect the BROWN live wire to the live terminal ‘L’.
b) Connect the BLUE neutral wire to the neutral terminal ‘N’.
c) After wiring, check that there are no bare wires, that all wires have been correctly connected, that
the cable outer insulation extends beyond the cable restraint and that the restraint is tight.
1.4.
BATTERY CHARGER SAFETY INSTRUCTIONS
F WARNING! DO NOT attempt to charge any battery other than that specified. Other types of battery may explode!
! All mains electrical supply safety features must be followed as described in Section 1.3. above.
! Disconnect the charger from the mains power supply when not in use.
% DO NOT expose the charger to damp or wet conditions.
% DO NOT pull or carry the charger by the power lead.
% DO NOT operate the charger if it has been dropped, or has received a sharp knock, or is damaged. Take charger
to an authorised agent.
% DO NOT dismantle the charger as this may cause damage and/or personal injury and will invalidate your warranty.
% DO NOT insert foreign objects into the hole reserved for the battery pack.
% DO NOT recharge a second battery pack immediately after charging the first. Consecutive charging will overheat
the charger. Allow the unit to cool for 15 minutes before charging the next pack.
% DO NOT attempt to connect two chargers together.
! Store the charger in the same manner as the battery pack, see Section 1.2.
2. INTRODUCTION & OPERATION
2.1.
INTRODUCTION
The CP1810 Halogen Lantern is powered by a sealed, rechargeable, 18 volt Ni-Cad battery pack as supplied
with the CP2018VHK Cordless Hammer Drill. The battery and battery charger are not supplied with this lantern.
2.2.
OPERATION
F
WARNING! Ensure you read and understand the safety instructions before using the lantern or charger.
p
1. Charge the battery before use (para. 2.3).
2. Turn lantern ‘On’ and ‘Off’ by the switch on the main body.
3. The lantern has an adjustable carrying handle.
Brown
Live
Wire
Blue
Neutral
Wire
Cable
Restraint
FUSE RATING 3 AMP
2.3.
BATTERY CHARGING
F
WARNING! Ensure that you read, understand and apply the safety instructions relating to the battery
p
and charger before use.
1. Remove the battery from the lantern by depressing the two latch buttons (fig. 1.A).
2. Insert battery into the charger (as supplied with the CP2018VHK Cordless Hammer Drill). Note that the
battery will only fit one way round - DO NOT use force. See fig. 2.
3. Plug the charger into the mains supply and switch on.
4. The red LED on the charger will illuminate to indicate that the battery is being charged. When the battery
is fully charged (approx. 1 hour) the green LED will illuminate.
5. Switch off the mains supply to the charger. Remove the battery from the charger and refit it to the lantern.
6. Store the charger in a safe, dry location.
Notes: a) Battery packs are shipped in a low charge state. They take longer to charge initially, and several subsequent
charges may also take a little longer, than when they reach optimum performance.
b) A fully charged battery will last for approximately two hours.
c) There is no need to fully discharge the battery before recharging.
3.
MAINTENANCE
3.1.
CHANGING THE LANTERN BULB
F
WARNING! Ensure that lantern is turned off and the lens has cooled
prior to changing the bulb.
1. Unscrew the lens ring (fig. 1.B) and remove ring, lens and reflector as one.
2. Pull the failed bulb from the bulb holder.
3. Hold the new bulb with a lint-free cloth (do not touch the bulb directly)
and push it into bulb holder.
fig. 1
PARTS FOR: CP1810
RECHARGEABLE LANTERN
Part No.
CP1810/B
CB18/99
CP9918VHK/32
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications
and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this equipment.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full
name and address, including postcode.
Sole UK Distributor,
Sealey Group,
01284 703534
Bury St. Edmunds, Suffolk.
Description
Bulb, 18V 10W
Battery Pack
Mains Charger
01284 757500
www.sealey.co.uk
9A>
sales@sealey.co.uk
e-mail
CP1810 - 1 - 260303
fig. 2
Advertisement
