Page 2
I M P O R T A N T Get warranty and othe r informati on online – you ca n revi ew an d prin t or d o wn lo a d a c op y o f t h e Ow n er ’s M a n u a l, Na viga ti on/U connect manuals and the limited warra n ti es p rovi d ed b y FCA US L LC f or y ou r ve h ic le b y vi si tin g w ww.mopar.com (U.S.) or www.owners.mopar.ca (Ca n ad a ).
Congratulations on selecting your new FCA US This User Guide has been prepared to help you For more detailed descriptions of the topics quickly become acquainted with the important LLC vehicle. Be assured that it represents pre- discussed in this User Guide, as well as infor- features of your vehicle.
To identify the chapter with the information HOW TO USE THIS MANUAL WARNINGS AND CAUTIONS needed you can consult the index at the end of While reading this User Guide you will find a this User Guide. Essential Information series of WARNINGS to be followed to prevent Each time direction instructions (left/right or Chapters can be rapidly identified with dedi- incorrect use of components which could cause...
GRAPHICAL TABLE OF CONTENTS GETTING TO KNOW YOUR VEHICLE GETTING TO KNOW YOUR INSTRUMENT PANEL SAFETY STARTING AND OPERATING IN CASE OF EMERGENCY SERVICING AND MAINTENANCE TECHNICAL SPECIFICATIONS MULTIMEDIA CUSTOMER ASSISTANCE INDEX...
To remove the emergency key, slide the me- KEYS chanical latch on the back of the key fob side- ways with your thumb and then pull the key out Key Fob with your other hand. Your vehicle uses a keyless ignition system. The ignition system consists of a key fob with Re- NOTE: mote Keyless Entry (RKE) and a START/STOP...
Page 12
The Panic Alarm will stay on for three minutes To Lock The Doors And Liftgate Backup Starting Method unless you turn it off by either pushing the Panic In case the ignition switch does not change with Push and release the lock button on the key fob button a second time or drive the vehicle at a the push of a button, the key fob may have a low to lock all doors and liftgate.
2. This device must accept any interference The push button ignition can be placed in the NOTE: If the ignition switch does not change with the received, including interference that may following modes: push of a button, the key fob may have a low or cause undesired operation.
NOTE: WARNING! WARNING! Refer to "Starting The Engine," in "Starting And • Allowing children to be in a vehicle unat- Operating" in the Owner’s Manual for further • Do not start or run an engine in a closed tended is dangerous for a number of rea- information.
• The park lamps will turn on and remain on NOTE: To Arm The System Changes or modifications not expressly ap- during Remote Start mode. Follow these steps to arm the vehicle security proved by the party responsible for compliance •...
DOORS To Disarm The System NOTE: • The driver's door key cylinder and the liftgate The vehicle security alarm can be disarmed Keyless Enter-N-Go — Passive Entry button on the key fob cannot arm or disarm using any of the following methods: the vehicle security alarm.
Page 17
• If the vehicle is unlocked by Passive Entry and To Unlock From The Passenger Side: no door is opened within 60 seconds, the With a valid Passive Entry key fob within 5 ft vehicle will re-lock and if equipped will arm (1.5 m) of the passenger door handle, grab the the security alarm.
Page 18
If one of the vehicle doors is open and the vehicle is locked with a door panel switch, key fob button or door handle button, once all open doors have been closed the vehicle checks the inside and outside of the vehicle for any valid Passive Entry key fobs.
• If Passive Entry is disabled using Uconnect NOTE: System, the key protection described in "Pre- Changes or modifications not expressly ap- venting Inadvertent Locking of Passive Entry proved by the party responsible for compliance key fob in Vehicle" remains active/functional. could void the user’s authority to operate the equipment.
SEATS WARNING! Seats are a part of the Occupant Restraint Avoid trapping anyone in a vehicle in a collision. System of the vehicle. Remember that the rear doors can only be opened from the outside when the Child-Protection locks WARNING! are engaged.
Move the control lever on the upper outboard Manual Adjustment (Rear Seats) WARNING! side of the seatback forward. Then, in one fluid • Do not allow people to ride in any area of motion, the seat cushion flips upward and the WARNING! your vehicle that is not equipped with seats seat moves forward on its tracks.
Page 22
2. Place one hand on the seatback and apply a Manual Folding Second Row Seat WARNING! gentle pressure. To Fold The Seat Do not drive the vehicle with the seat in this 3. Lift the control lever with the other hand, position, as it is only intended for entering and allow the seatback to move forward slightly, exiting the third row seats.
Page 23
The seatback can also be locked in the reclined To Unfold The Seat To Fold The Seatback position. To do so, pull the latch release-loop Raise the seatback and lock it in place. Pull the latch release-loop located at the top of located at the top of the seatback upward, allow the seatback upward, push the seatback for- the seatback to recline, and release the...
HEAD RESTRAINTS Front Heated Seats Vehicles Equipped With Remote Start On models that are equipped with remote start, If your vehicle is equipped with front heated Head restraints are designed to reduce the risk the heated seats can be programmed to come seats, the control buttons are located within the of injury by restricting head movement in the Uconnect system.
Supplemental Active Head Restraints (AHR) — Front Seats Supplemental Active Head Restraints are pas- sive, deployable components, and vehicles with this equipment can not be readily identified by any markings, only through visual inspection of the head restraint. The head restraint will be split in two halves, with the front half being soft foam and trim, the back half being decorative plastic.
Rear Head Restraint Adjustment WARNING! The second row seats are equipped with adjust- • All occupants, including the driver, should able and removable head restraints. To raise the not operate a vehicle or sit in a vehicle’s head restraint, pull upward on the head re- seat until the head restraints are placed in straint.
desired. To lengthen or shorten the steering NOTE: WARNING! For proper routing of a Child Seat Tether, refer to column, pull the steering wheel outward or push “Occupant Restraint Systems” in “Safety” in it inward as desired. To lock the steering column A loose head restraint thrown forward in a your Owner's Manual for further information.
The heated steering wheel control button is WARNING! located within the Uconnect system. You can gain access to the control button through the • Persons who are unable to feel pain to the climate screen or the controls screen. skin because of advanced age, chronic illness, diabetes, spinal cord injury, medi- •...
Daytime Running Lights (DRL) Automatic Headlights The Daytime Running Lights will turn on the This system automatically turns the headlights first time the vehicle is shifted out of PARK, and on or off according to ambient light levels. To remain on unless the parking brake is applied. turn the system on, rotate the headlight switch Upon returning to the PARK position, the DRLs counterclockwise to the AUTO position.
An indicator light in the instrument cluster illu- Headlights On With Wipers (Available With NOTE: minates when the fog lights are turned on. The lights must be turned off within 45 seconds Automatic Headlights Only) of turning the ignition OFF to activate this fea- NOTE: When this feature is active, the headlights will ture.
WIPERS AND WASHERS Windshield Wiper Operation CAUTION! Rotate the end of the lever upward, to the first • Always remove any buildup of snow that The windshield wiper/washer control lever is detent past the intermittent settings for low-speed prevents the windshield wiper blades from located on the left side of the steering column.
NOTE: Rear Window Wiper/Washer WARNING! The wiper delay times depend on vehicle speed. The rear window wiper/washer control is located If the vehicle is moving less than 10 mph Sudden loss of visibility through the wind- on the left side of the steering column. (16 km/h), delay times will be doubled.
CLIMATE CONTROLS CAUTION! • In cold weather, always turn off the wiper The Climate Control System allows you to regu- switch and allow the wipers to return to the late the temperature, air flow, and direction of park position before turning off the engine. air circulating throughout the vehicle.
Page 34
Automatic Climate Controls Descriptions Icon Description MAX A/C Button Press the button on the touchscreen to change the current setting, the indicator illuminates when MAX A/C is on. Pressing it again turns the MAX A/C operation to switch into manual mode and the MAX A/C indicator turns off. NOTE: The MAX A/C button is only available on the touchscreen.
Page 35
Icon Description Rear Defrost Button The Rear Defrost Control button turns on the rear window defroster and the heated outside mirrors (if equipped). An indicator will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after ten minutes. Rear Climate Control Button Press and release this button to access the rear climate controls.
Page 36
Icon Description Faceplate Knob Blower Control Blower Control is used to regulate the amount of air forced through the climate system. There are seven blower speeds avail- able. The speeds can be selected using either the blower control knob on the faceplate or the buttons on the touchscreen. •...
Page 37
Icon Description Floor Mode Floor Mode Air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. Mix Mode Mix Mode Air is directed through the floor, defrost, and side window demister outlets. This setting works best in cold or snowy conditions that require extra heat to the windshield.
Page 38
Icon Description Rear Auto Button Automatically controls the rear interior cabin temperature by adjusting airflow distribution and amount. Performing this func- tion will cause the system to switch between manual mode and automatic modes. Refer to "Automatic Operation" within this section for more information.
Page 39
Icon Description Blower Control Blower Control is used to regulate the amount of air forced through the climate system. There are seven blower speeds avail- able. Adjusting the blower will cause automatic mode to switch to manual operation. The speeds can be selected using the buttons on the touchscreen.
Page 40
1. Adjust the Rear Blower, Rear Temperature Rear Automatic Temperature Control (ATC) NOTE: and the Rear Modes to suit your comfort • It is not necessary to move the temperature needs. settings. The system automatically adjusts the temperature, mode and fan speed to pro- 2.
Page 41
Icon Description Bi-Level Mode Bi-Level Mode Air comes from both the headliner outlets and the floor outlets. NOTE: In many temperature positions, the Bi-Level mode is designed to provide cooler air out of the headliner outlets and warmer air from the floor outlets. Floor Mode Floor Mode Air comes from the floor outlets.
Icon Description Rear Climate Control/Blower Off To manually set the rear blower controls to off, press the Rear Climate Control/Blower Off button. • If fog or mist appears on the windshield or In MAX A/C, the blower level and mode position Climate Control Functions side glass, select Defrost mode, and increase can be adjusted to desired user settings.
• The temperature can be displayed in U.S. or Winter Operation Automatic Temperature Control (ATC) — Metric units by selecting the US/Metric cus- If Equipped To ensure the best possible heater and defroster tomer programmable feature. Refer to the performance, make sure the engine cooling sys- “Uconnect Settings”...
There are single window controls on each pas- A/C Air Filter CAUTION! senger door trim panel, which operate the pas- The climate control system filters out dust and senger door windows. The window controls will Failure to follow these cautions can cause pollen from the air.
Page 45
To close the window part way, pull the window Auto-Down Feature Window Lockout Switch switch up to the first detent and release it when The driver's power window switch has an Auto- The window lockout switch on the driver's door you want the window to stop.
POWER SUNROOF — IF EQUIPPED Wind Buffeting WARNING! Wind buffeting can be described as the percep- The power sunroof switch is located between • Never leave children unattended in a ve- tion of pressure on the ears or a helicopter-type the sun visors on the overhead console.
Opening Sunroof Closing Sunroof Anti Pinch Protect Feature This feature will detect an obstruction in the Express Express opening of the sunroof during Express Close Push the switch rearward and release it within Push the switch forward and release it within operation.
3. Use the hood prop rod to secure the hood in the HOOD LIFTGATE open position. Place the upper end of the prop rod in the hole on the underside of the hood. Opening Opening Two latches must be released to open the hood. The liftgate can be unlocked or locked pushing Closing the unlock or lock button on the Remote Key-...
UNIVERSAL GARAGE DOOR OPENER WARNING! (HOMELINK) • Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. •...
• To operate HomeLink, push and release any of Erasing All The HomeLink Channels Rolling Code Devices the programmed HomeLink buttons. These To determine if your device has a rolling code, a To erase the channels, follow this procedure: buttons will activate the devices they are pro- good indicator is its manufacturing date.
Programming HomeLink To A Garage Door NOTE: Non-Rolling Code Garage Door Opener Final Make sure the garage door opener motor is Steps Opener plugged in before moving on to the rolling code/ 1. Push and hold the programmed HomeLink To program any of the HomeLink buttons to non-rolling code final steps.
Programming HomeLink To A Reprogramming A Single HomeLink Button General Information Miscellaneous Device To reprogram a single HomeLink button that has The following regulatory statement applies to all been previously trained, without erasing all the Radio Frequency (RF) devices equipped in this Refer to “Programming HomeLink To A Garage channels, follow the procedure below.
This power outlet will also operate a conven- INTERNAL EQUIPMENT tional cigar lighter unit. To preserve the heating Power Outlets element, do not hold the lighter in the heating position. A 12 Volt (13 Amp) power outlet is located in the center console below the radio.
Page 54
CAUTION! • Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is ex- ceeded the fuse protecting the system will need to be replaced. • The power outlet on the bottom of the center console shares the fuse with the power outlet on the back of the console.
Page 55
Power Outlet Fuses 1 — F103 20 Amp Yellow — Power Outlet Console Bin And Power Outlet Console Rear 2 — F102 20 Amp Yellow — Cigar Lighter Instrument Panel And Power Outlet Left Rear Cargo Area...
WARNING! CAUTION! • After the use of high power draw accesso- To avoid serious injury or death: ries, or long periods of the vehicle not • Only devices designed for use in this type being started (with accessories still of outlet should be inserted into any plugged in), the vehicle must be driven a 12 Volt outlet.
To reset the inverter manually press the power Power Inverter Operation ROOF LUGGAGE RACK — IF inverter button OFF and ON. To avoid overload- The power inverter is turned On and Off using EQUIPPED ing the circuit, check the power ratings on the Uconnect System.
Page 58
2. Relocate the crossbars, aligning the crossbar The tie down holes on the crossbar ends CAUTION! stanchions (end pieces) with one of the ver- should always be used to tie down the load. • Crossbars should remain equally spaced or tical marks on the outboard surface of the Check the straps frequently to be sure that the parallel at any roof rack position for proper...
The system allows the driver to select informa- INSTRUMENT CLUSTER DISPLAY Instrument Cluster Display Location And tion by pushing the following buttons mounted Controls Your vehicle may be equipped with an instru- on the steering wheel: The instrument cluster display features a driver- ment cluster display, which offers useful infor- interactive display that is located in the instru- mation to the driver.
• Down Arrow Button Unless reset, this message will continue to dis- Instrument Cluster Display Selectable play each time you cycle the ignition to the Menu Items Push and release the down arrow button to ON/RUN position. To turn off the message tem- scroll downward through the main menus and Push and release the up or down arrow button porarily, push and release the up arrow button.
Page 61
Load reduction is only active when the engine is The electrical loads that may be switched off (if • Unusual driving cycles (short trips separated running. It will display a message if there is a equipped), and vehicle functions which can be by long parking periods).
After a trip: — Brake Warning Light Red Warning Lights • Check if any aftermarket equipment was in- This warning light monitors various brake func- — Seat Belt Reminder Warning Light stalled (additional lights, upfitter electrical tions, including brake fluid level and parking This warning light indicates when the driver or accessories, audio systems, alarms) and re- brake application.
Page 63
Warning Light, which will turn on when the Operation of the Brake Warning Light can be — Engine Coolant Temperature Warn- brake fluid level in the master cylinder has checked by turning the ignition switch from the ing Light dropped below a specified level. OFF position to the ON/RUN position.
Page 64
transmission in PARK or NEUTRAL, until the This indicates a possible problem with the elec- turn off. If the light remains on with the vehicle light turns off. Once the light turns off, you may trical system or a related component. running, your vehicle will usually be drivable;...
converter damage. The vehicle should be ser- Yellow Warning Lights WARNING! viced by an authorized dealer as soon as pos- — Engine Check/Malfunction Indica- sible if this occurs. Continued operation with reduced assist tor Warning Light (MIL) could pose a safety risk to yourself and oth- WARNING! ers.
Page 66
— Electronic Stability Control (ESC) — Electronic Stability Control (ESC) Off CAUTION! Active Warning Light — If Equipped Warning Light — If Equipped steering. If a tire puncture occurs, repair This warning light will indicate when the Elec- This warning light indicates the Electronic Sta- immediately using the dedicated tire repair tronic Stability Control system is Active.
Page 67
tire failure. Under-inflation also reduces fuel vehicle that prevent the TPMS from functioning — Anti-Lock Brake (ABS) Warning efficiency and tire tread life, and may affect the properly. Always check the TPMS malfunction Light vehicle’s handling and stopping ability. telltale after replacing one or more tires or This warning light monitors the Anti-Lock Brake wheels on your vehicle to ensure that the re- Please note that the TPMS is not a substitute for...
— Low Washer Fluid Warning Light — NOTE: Blue Indicator Lights If Equipped • A continuous chime will sound if the vehicle is — High Beam Indicator Light driven more than 1 mile (1.6 km) with either This warning light will illuminate when the This indicator light will illuminate to indicate turn signal on.
If any of these systems require service, the OBD Onboard Diagnostic System (OBD II) WARNING! II system will turn on the Malfunction Indicator Cybersecurity • Be possible that vehicle systems, in- Light (MIL). It will also store diagnostic codes Your vehicle is required to have an Onboard cluding safety related systems, could and other information to assist your service Diagnostic system (OBD II) and a connection...
The TPMS will warn the driver of a low tire nates, you must increase the tire pressure to the AUXILIARY DRIVING SYSTEMS pressure if the tire pressure falls below the recommended cold placard pressure in order for low-pressure warning limit for any reason, in- the Tire Pressure Monitoring System Warning Tire Pressure Monitoring System (TPMS) cluding low temperature effects and natural...
Page 71
Warning Light. Driving the vehicle may cause • The TPMS is not a substitute for proper tire CAUTION! maintenance, and it is the driver’s responsibil- the tire pressure to rise to approximately 28 psi • Using aftermarket tire sealants may cause ity to maintain correct tire pressure using an (193 kPa), but the Tire Pressure Monitoring the Tire Pressure Monitoring System...
Page 72
The TPMS consists of the following compo- NOTE: nents: When filling warm tires, the tire pressure may need to be increased up to an additional 4 psi • Receiver module (28 kPa) above the recommended cold placard • Four tire pressure monitoring sensors pressure in order to turn the Tire Pressure Moni- toring System Warning Light off.
Page 73
TEM" message will no longer display, and a chime will sound. In addition, the graphic in display a new pressure value instead of dashes the instrument cluster will still display a pres- (- -), as long as no tire pressure is below the pressure value will display in place of the sure value in a different color and an "Inflate low-pressure warning limit in any of the four...
Beginning with the next ignition cycle, the General Information OCCUPANT RESTRAINT SYSTEMS TPMS will no longer chime or display the “Ser- The following regulatory statement applies to all Some of the most important safety features in vice Tire Pressure System” message in the in- radio frequency (RF) devices equipped in this your vehicle are the restraint systems: strument cluster but dashes (--) will remain in...
Here are some simple steps you can take to 6. All occupants should always wear their lap WARNING! minimize the risk of harm from a deploying air and shoulder belts properly. • Never install a rear-facing child restraint in bag: 7.
Page 76
The outboard front passenger seat BeltAlert is Enhanced Seat Belt Use Reminder System BeltAlert Warning Sequence not active when the outboard front passenger (BeltAlert) The BeltAlert warning sequence is activated seat is unoccupied. BeltAlert may be triggered when the vehicle is moving above a specified Driver and Passenger BeltAlert (if equipped) when an animal or other items are placed on the vehicle speed range and the driver or outboard...
Page 77
Lap/Shoulder Belts WARNING! WARNING! All seating positions in your vehicle are • It is dangerous to ride in a cargo area, lap/shoulder belt or a lap belt for more than equipped with lap/shoulder belts. inside or outside of a vehicle. In a collision, one person, no matter what their size.
Page 78
1. Enter the vehicle and close the door. Sit WARNING! WARNING! back and adjust the seat. • A seat belt that is too loose will not protect modify the seat belt system. Seat belt 2. The seat belt latch plate is above the back of you properly.
Page 79
6. To release the seat belt, push the red button belt away from your neck. Push or squeeze the NOTE: anchorage button to release the anchorage, and The adjustable upper shoulder belt anchorage is on the buckle. The seat belt will automati- move it up or down to the position that serves equipped with an Easy Up feature.
Page 80
Position the lap belt snug and low below the Seat Belt Extender WARNING! abdomen and across the strong bones of the If a seat belt is not long enough to fit properly, long enough and only use in the recom- hips.
Page 81
essary to comfortably wrap around the occu- Energy Management Feature — If Equipped pant’s mid-section. Slide the latch plate into the The front outboard seat belt system is equipped buckle until you hear a "click." and the second row outboard seat belt system In Automatic Locking Mode, the shoulder belt is may be equipped with an Energy Management automatically pre-locked.
Page 82
How To Engage The Automatic Locking Mode How The Active Head Restraints (AHR) Work WARNING! 1. Buckle the combination lap and shoulder The Occupant Restraint Controller (ORC) deter- • Failure to replace the seat belt assembly belt. mines whether the severity or type of rear im- could increase the risk of injury in colli- pact will require the Active Head Restraints sions.
Page 83
Active Head Restraint (AHR) Components: NOTE: WARNING! For more information on properly adjusting and positioning the head restraint, refer to “Head • All occupants, including the driver, should Restraints” in “Getting To Know Your Vehicle.” not operate a vehicle or sit in a vehicle’s seat until the head restraints are placed in Resetting Active Head Restraints (AHR) their proper positions in order to minimize...
into the original position to best protect the the battery loses power or it becomes discon- Air Bag System Components occupant for all types of collisions. An autho- nected prior to deployment. • Occupant Restraint Controller (ORC) rized FCA US LLC dealer must reset the AHRs The ORC turns on the Air Bag Warning Light in •...
Page 85
• The Air Bag Warning Light remains on after Front Air Bags the four to eight-second interval. This vehicle has front air bags and lap/shoulder • The Air Bag Warning Light comes on intermit- belts for both the driver and front passenger. tently or remains on while driving.
Page 86
Driver And Passenger Front Air Bag WARNING! WARNING! Features • Being too close to the steering wheel or • No objects should be placed over or near The Advanced Front Air Bag system has multi- instrument panel during front air bag de- the air bag on the instrument panel or stage driver and front passenger air bags.
Page 87
When the ORC detects a collision requiring the Front Air Bag Operation Supplemental Driver Knee Air Bag front air bags, it signals the inflator units. A Front Air Bags are designed to provide addi- This vehicle is equipped with a Supplemental large quantity of non-toxic gas is generated to tional protection by supplementing the seat Driver Knee Air Bag mounted in the instrument...
Page 88
The SABs may help to reduce the risk of occu- the door. The SAB moves at a very high speed pant injury during certain side impacts, in ad- and with such a high force that it could injure dition to the injury reduction potential provided occupants if they are not seated properly, or if by the seat belts and body structure.
Page 89
The SABIC deploys downward, covering the side The Side Air Bags will not deploy in all side WARNING! windows. An inflating SABIC pushes the out- collisions, including some collisions at certain vehicle. Do not add roof racks that require side edge of the headliner out of the way and angles, or some side collisions that do not im- permanent attachments (bolts or screws) covers the window.
Page 90
Air Bag System Components Rollover Events WARNING! Side Air Bags are designed to activate in certain NOTE: seat belts properly and sit upright with rollover events. The ORC determines whether The Occupant Restraint Controller (ORC) moni- their backs against the seats. Children the deployment of the Side Air Bags in a par- tors the internal circuits and interconnecting must be properly restrained in a child re-...
Page 91
irritation, rinse the area with cool water. For If A Deployment Occurs Enhanced Accident Response System nose or throat irritation, move to fresh air. If The front air bags are designed to deflate imme- In the event of an impact, if the communication the irritation continues, see your doctor.
Page 92
• Cut off battery power to the: Enhanced Accident Response System Reset WARNING! – Engine Procedure • It is dangerous to try to repair any part of – Electric Motor (if equipped) In order to reset the Enhanced Accident Re- the air bag system yourself.
Children 12 years or younger should ride prop- Event Data Recorder (EDR) NOTE: erly buckled up in a rear seat, if available. EDR data are recorded by your vehicle only if a This vehicle is equipped with an event data According to crash statistics, children are safer non-trivial crash situation occurs;...
Page 94
Before buying any restraint system, make sure • Canadian residents should refer to Transport NOTE: that it has a label certifying that it meets all Canada’s website for additional information: • For additional information, refer to http:// applicable Safety Standards. You should also http://www.tc.gc.ca/eng/motorvehiclesafety/ www.nhtsa.gov/parents-and-caregivers or call: make sure that you can install it in the vehicle...
Page 95
Infant And Child Restraints WARNING! WARNING! Safety experts recommend that children ride Do not install a rear-facing car seat using a • Never place a rear-facing child restraint in rear-facing in the vehicle until they are two years rear support leg in this vehicle. The floor of front of an air bag.
Page 96
Older Children And Child Restraints Integrated Child Booster Seat — If WARNING! Equipped Children who are two years old or who have • Improper installation can lead to failure of The Integrated Child Booster Seat is located in outgrown their rear-facing convertible child seat an infant or child restraint.
Page 97
To position a child into the Integrated Child 3. Lift the seat cushion up and push back to 6. Slide the latch plate up the webbing as far as lock it in the booster seat position. Booster Seat follow these steps: necessary to allow the seat belt to go around the child’s lap.
Page 98
If the answer to any of these questions was Children Too Large For Booster Seats WARNING! “no,” then the child still needs to use a booster Children who are large enough to wear the seat in this vehicle. If the child is using the In a severe collision, the booster seat may be shoulder belt comfortably, and whose legs are lap/shoulder belt, check seat belt fit periodically...
Page 99
Recommendations For Attaching Child Restraints Restraint Type Combined Weight of the Use Any Attachment Method Shown With An “X” Below Child + Child Restraint LATCH – Lower Anchors Seat Belt Only LATCH – Lower Anchors Seat Belt + Top Tether Only + Top Tether Anchor Anchor...
Page 100
Your vehicle is equipped with the child restraint Lower Anchors And Tethers For CHildren LATCH Positions For Installing Child anchorage system called LATCH, which stands Restraints In This Vehicle (LATCH) Restraint System for Lower Anchors and Tethers for CHildren. The LATCH system has three vehicle anchor points for installing LATCH-equipped child seats.
Page 101
Frequently Asked Questions About Installing Child Restraints With LATCH Use the LATCH anchorage system until the combined weight of the child What is the weight limit (child’s weight + weight and the child restraint is 65 lbs (29.5 kg). Use the seat belt and tether an- of the child restraint) for using the LATCH anchor- 65 lbs (29.5 kg) chor instead of the LATCH system once the combined weight is more than...
Page 102
facing child restraints will also be equipped Locating The LATCH Anchorages Locating The Upper Tether Anchorages with a tether strap. The tether strap will have a hook at the end to attach to the top tether The lower anchorages are round bars that are There are tether strap anchorages behind each anchorage and a way to tighten the strap after it found at the rear of the seat cushion where it...
Page 103
2. Left outboard and center seating positions WARNING! (3 and 2): Install the first child seat in the • If you are installing three child restraints left outboard seating position using lower next to each other, you must use the seat anchorages D and E.
Page 104
1. Loosen the adjusters on the lower straps and 5. Tighten all of the straps as you push the child straint installation, instead of buckling it behind on the tether strap of the child seat so that restraint rearward and downward into the seat. the child restraint, route the seat belt through you can more easily attach the hooks or Remove slack in the straps according to the...
Page 105
are designed to keep the lap portion of the seat Installing Child Restraints Using The Ve- Lap/Shoulder Belt Systems For Installing belt tight around the child restraint so that it is hicle Seat Belt Child Restraints In This Vehicle not necessary to use a locking clip. The ALR Child restraint systems are designed to be se- retractor can be “switched”...
Page 106
Frequently Asked Questions About Installing Child Restraints With Seat Belts What is the weight limit (child’s weight + weight Always use the tether anchor when using the seat belt to install a forward of the child restraint) for using the Tether Anchor Weight limit of the facing child restraint, up to the recommended weight limit of the child re- with the seat belt to attach a forward facing child...
Page 107
2. Pull enough of the seat belt webbing from 7. Finally, pull up on any excess webbing to Installing A Child Restraint With A Cinching the retractor to pass it through the belt path tighten the lap portion around the child re- Latch Plate (CINCH) —...
Page 108
2. Next, pull enough of the seat belt webbing Any seat belt system will loosen with time, so Installing Child Restraints Using The Top from the retractor to pass it through the belt check the belt occasionally, and pull it tight if Tether Anchorage path of the child restraint.
Page 109
1. Look behind the seating position where you 2. Route the tether strap to provide the most plan to install the child restraint to find the direct path for the strap between the anchor tether anchorage. You may need to move the and the child seat.
SAFETY TIPS Exhaust Gas WARNING! • If your vehicle is equipped with a split rear Transporting Passengers WARNING! seat, make sure the tether strap does not NEVER TRANSPORT PASSENGERS IN THE slip into the opening between the seat- Exhaust gases can injure or kill. They contain CARGO AREA.
Whenever a change is noticed in the sound of Air Bag Warning Light Floor Mat Safety Information the exhaust system, when exhaust fumes can be The Air Bag warning light will turn on for Always use floor mats designed to fit your ve- detected inside the vehicle, or when the under- four to eight seconds as a bulb check when the hicle.
Periodic Safety Checks You Should Make WARNING! WARNING! Outside The Vehicle • ALWAYS REMOVE THE EXISTING FLOOR • ALWAYS make sure objects cannot fall or slide into the driver’s side floor area when MAT FROM THE VEHICLE before Tires the vehicle is moving. Objects can become installing any other floor mat.
Page 113
Door Latches Check for proper closing, latching, and locking. Fluid Leaks Check area under the vehicle after overnight parking for fuel, coolant, oil, or other fluid leaks. Also, if gasoline fumes are detected or if fuel, or brake fluid leaks are suspected. The cause should be located and corrected immediately.
ENGINE BREAK-IN CAUTION! RECOMMENDATIONS — GASOLINE Never use Non-Detergent Oil or Straight Min- ENGINE eral Oil in the engine or damage may result. A long break-in period is not required for the NOTE: engine and drivetrain (transmission and axle) in A new engine may consume some oil during its your vehicle.
NOTE: To Set A Desired Speed U.S. Speed (mph) In order to ensure proper operation, the Speed • Pushing the RES (+) button once will result in Turn the Speed Control on. When the vehicle Control System has been designed to shut down a 1 mph increase in set speed.
• If the button is continually pushed, the set To Decrease Speed WARNING! speed will continue to decrease until the but- When the Speed Control is set, you can de- tions, and you could lose control and have an ton is released, then the new set speed will be crease speed by pushing the SET (-) button.
PARKSENSE REAR PARK ASSIST — ParkSense Sensors Enabling And Disabling ParkSense IF EQUIPPED The four ParkSense sensors, located in the rear ParkSense can be enabled and disabled using fascia/bumper, monitor the area behind the ve- the Uconnect System. The available choices The ParkSense Rear Park Assist system pro- hicle that is within the sensors’...
Page 118
• Jackhammers, large trucks, and other vibra- can result in the system misinterpreting a WARNING! close object as a sensor problem, causing the tions could affect the performance of mount and hitch ball assembly, depending “SERVICE PARK ASSIST SYSTEM” message ParkSense.
When the vehicle is shifted out of REVERSE, Static grid lines will illustrate the width of the PARKVIEW REAR BACK UP the rear camera mode is exited and the last vehicle. These lines will show separate zones CAMERA selected touchscreen appears again. that will help indicate the distance to the rear of the vehicle.
NOTE: WARNING! WARNING! If snow, ice, mud, or any foreign substance • A fire may result if gasoline is pumped into builds up on the camera lens, clean the lens, Drivers must be careful when backing up a portable container that is inside of a rinse with water, and dry with a soft cloth.
Indiscriminate use of fuel system cleaning NOTE: Materials Added To Fuel agents should be avoided. Many of these mate- • Tighten the gas cap until you hear a “clicking” rials intended for gum and varnish removal may Designated TOP TIER sound.
TRAILER TOWING Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain: GCWR (Gross Combined Wt. Engine/Transmission Frontal Area Max. GTW (Gross Trailer Wt.) Max. Tongue Wt. Rating) 1,000 lbs (453 kg) which includes up to 6,000 lbs (2,721 kg) 22 sq ft (2.0 sq m) 100 lbs (45 kg)
RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing This Vehicle Behind Another Vehicle Towing Condition Wheel OFF the Ground FWD Models AWD Models Flat Tow NONE NOT ALLOWED NOT ALLOWED Front NOT ALLOWED Dolly Tow Rear NOT ALLOWED NOT ALLOWED On Trailer NOTE: When towing your vehicle, always follow applicable state and provincial laws.
BULB REPLACEMENT Replacement Bulbs Interior Bulbs Bulb Number Courtesy/Reading Lamps (Incandescent) Courtesy/Reading Lamps (Optional LED) LED (Serviced at authorized dealer) Glove Compartment Lamp Cargo Lamp Optional Door Map Pocket/Cupholder LED (Serviced at authorized dealer) For lighted switches, see your authorized dealer for replacement instructions. Exterior Bulbs Bulb Number Low Beam Headlamp...
Exterior Bulbs – Rear (LED Version) Bulb Number Rear Tail/Stop Lamp LED (Serviced at authorized dealer) Rear Tail (Liftgate) Lamp LED (Serviced at authorized dealer) Rear Turn Signal Lamp WY21W or 7440A Backup Lamp W21W or 7440 Exterior Bulbs – Rear (Bulb Version) Bulb Number Rear Tail/Stop/Turn Signal Lamp P27/7W or 3157...
Interior Fuses The interior fuse panel is located on the passen- ger side under the instrument panel. Cavity Cartridge Fuse Mini-Fuse Description F100 30 Amp Pink – 110V AC Inverter – If Equipped F101 – 10 Amp Red Interior Lights F102 –...
space when accessing the jacking tools and JACKING AND TIRE CHANGING Jack Location when operating the winch mechanism. The jack and jack-handle are stowed underneath a 1. Remove the jack-handle components 1, WARNING! cover in the rear storage bin in the cargo area. 2 and 3 from storage and assemble them.
3. Pull the spare tire out from underneath the NOTE: vehicle and raise it upright so the tire's tread Assemble components 2 and 3 by seating the is on the ground. small ball at the end of component 2 in the 4.
Page 132
WARNING! • Turn on the Hazard Warning flasher. • Block the wheel diagonally opposite the wheel to be raised. • Apply the parking brake firmly and set the transmission in PARK. • Never start or run the engine with the vehicle on a jack.
Page 133
3. Place the jack in the notches underneath the WARNING! lift area that is closest to the flat tire. Center the jack saddle between the drain flute for- Raising the vehicle higher than necessary mations on the sill flange. Turn the jack can make the vehicle less stable.
Page 134
7. Install the wheel nuts with the cone-shaped 10. Lower the jack to its fully closed position. end of the nut toward the wheel. Lightly 11. Place the deflated (flat) tire in the cargo tighten the wheel nuts. area. Do not stow the deflated tire in the spare tire stowage location.
Vehicles Without Wheel Covers Road Tire Installation WARNING! 1. Mount the road tire on the axle. Vehicles Equipped With Wheel Covers To avoid the risk of forcing the vehicle off the 2. Install the remaining lug nuts with the cone jack, do not tighten the wheel nuts fully until 1.
5. After 25 miles (40 km), check the lug nut JUMP STARTING Preparations For Jump Start torque with a torque wrench to ensure that The battery in your vehicle is located between If your vehicle has a discharged battery, it can all lug nuts are properly seated against the the left front headlight assembly and the left be jump started using a set of jumper cables...
4. If using another vehicle to jump start the Connecting The Jumper Cables WARNING! battery, park the vehicle within the jumper 1. Connect the positive (+) end of the jumper cable’s reach, apply the parking brake and • Take care to avoid the radiator cooling fan cable to the remote positive (+) post of the make sure the ignition is OFF.
5. Start the engine in the vehicle that has the If frequent jump starting is required to start your NOTE: booster battery, let the engine idle a few vehicle, you should have the battery and charg- There are steps that you can take to slow down minutes, and then start the engine in the ing system inspected at your authorized dealer.
GEAR SELECTOR OVERRIDE FREEING A STUCK VEHICLE CAUTION! If a malfunction occurs and the gear selector If your vehicle becomes stuck in mud, sand, or Driving with a hot cooling system could damage cannot be moved out of the PARK position, you snow, it can often be moved using a rocking your vehicle.
in your Owner’s Manual for further information. TOWING A DISABLED VEHICLE CAUTION! Once the vehicle has been freed, push the "ESC This section describes procedures for towing a Off" switch again to restore "ESC On" mode. • When “rocking” a stuck vehicle by shifting disabled vehicle using a commercial towing between DRIVE and REVERSE, do not service.
Proper towing or lifting equipment is required to If flatbed equipment is not available, and the CAUTION! prevent damage to your vehicle. Use only tow transmission is operable, the vehicle may be flat • Do not push or tow this vehicle with an- bars and other equipment designed for this towed (with all four wheels on the ground) under other vehicle as damage to the bumper...
ENHANCED ACCIDENT RESPONSE SYSTEM (EARS) This vehicle is equipped with an Enhanced Accident Response System. Please refer to “Occupant Restraint Systems” in “Safety” for further information on the En- hanced Accident Response System (EARS) function. EVENT DATA RECORDER (EDR) This vehicle is equipped with an Event Data Recorder (EDR).
Your authorized dealer will reset the oil change SCHEDULED SERVICING Once A Month Or Before A Long Trip: indicator message after completing the sched- • Check engine oil level. Your vehicle is equipped with an automatic oil uled oil change. If a scheduled oil change is •...
Maintenance Plan Required Maintenance Intervals. Refer to the maintenance plan on the following page for the required maintenance intervals. At Every Oil Change Interval As Indicated By Oil Change Indicator System: • Change oil and filter. • Rotate the tires. Rotate at the first sign of irregular wear, even if it occurs before the oil indicator system turns on. •...
Page 145
Mileage or time passed (whichever comes first) Or Years: Or Kilometers: Additional Inspections Inspect the CV joints. Inspect front suspension, tie rod ends, and replace if necessary. Inspect the brake linings, parking brake function. Additional Maintenance Replace engine air filter. Replace air conditioning filter.
Page 146
** The spark plug change interval is mileage Heavy Duty Use Of The Vehicle based only, yearly intervals do not apply. Change engine oil at 4,000 miles (6,500 km) or 350 hours of engine run time if the vehicle is WARNING! operated in a dusty and off road environment or is operated predominately at idle or only very...
RAISING THE VEHICLE Tire Markings NOTE: • P (Passenger) — Metric tire sizing is based on In the case where it is necessary to raise the U.S. design standards. P-Metric tires have the vehicle, go to an authorized dealer or service letter “P”...
Page 150
Tire Sizing Chart EXAMPLE: Example Size Designation: P215/65R15XL 95H, 215/65R15 96H, LT235/85R16C, T145/80D18 103M, 31x10.5 R15 LT P = Passenger car tire size based on U.S. design standards, or "..blank.." = Passenger car tire based on European design standards, or LT = Light truck tire based on U.S.
Page 151
EXAMPLE: Load Identification: Absence of the following load identification symbols on the sidewall of the tire indicates a Standard Load (SL) tire: • XL = Extra load (or reinforced) tire, or • LL = Light load tire or • C, D, E, F, G = Load range associated with the maximum load a tire can carry at a specified pressure Maximum Load –...
Page 152
EXAMPLE: 01 = Number representing the year in which the tire was manufactured (two digits) • 01 means the year 2001 • Prior to July 2000, tire manufacturers were only required to have one number to represent the year in which the tire was manufactured. Example: 031 could represent the 3rd week of 1981 or 1991 Tire Terminology And Definitions Term...
Page 153
This placard tells you important information Tire Loading And Tire Pressure about the: NOTE: 1. Number of people that can be carried in the The proper cold tire inflation pressure is listed vehicle. on the driver’s side B-Pillar or the rear edge of the driver's side door.
Page 154
(4) The resulting figure equals the avail- To determine the maximum loading conditions Metric Example For Load Limit of your vehicle, locate the statement “The com- able amount of cargo and luggage load For example, if “XXX” amount equals 635 kg bined weight of occupants and cargo should capacity.
Safety NOTE: WARNING! • Unequal tire pressures from side to side may WARNING! Overloading of your tires is dangerous. Over- cause erratic and unpredictable steering re- loading can cause tire failure, affect vehicle sponse. • Improperly inflated tires are dangerous handling, and increase your stopping dis- •...
Page 157
three hours, or driven less than 1 mile (1.6 km) Tire Inflation Pressures Tire Pressures For High Speed Operation after sitting for a minimum of three hours. The The proper cold tire inflation pressure is listed The manufacturer advocates driving at safe cold tire inflation pressure must not exceed the on the driver's side B-Pillar or rear edge of the speeds and within posted speed limits.
Page 158
Radial Ply Tires Run Flat Tires — If Equipped Tire Spinning Run Flat tires allow you the capability to drive When stuck in mud, sand, snow, or ice condi- WARNING! 50 miles (80 km) at 50 mph (80 km/h) after a tions, do not spin your vehicle's wheels above rapid loss of inflation pressure.
Page 159
• Tire pressure - Improper cold tire inflation Keep dismounted tires in a cool, dry place with pressures can cause uneven wear patterns to as little exposure to light as possible. Protect develop across the tire tread. These abnormal tires from contact with oil, grease, and gasoline. wear patterns will reduce tread life, resulting Replacement Tires in the need for earlier tire replacement.
It is recommended to replace the two front tires Tire Types WARNING! or two rear tires as a pair. Replacing just one tire All Season Tires — If Equipped dling and stress to steering and suspension can seriously affect your vehicle’s handling. If components.
Summer tires do not contain the all season four; failure to do so may adversely affect the safety CAUTION! designation or mountain/snowflake symbol on and handling of your vehicle. the tire sidewall. Use Summer tires only in sets Because of the reduced ground clearance, do Snow tires generally have lower speed ratings of four;...
Page 162
Inflate collapsible tire only after the wheel is Compact Spare Tire — If Equipped WARNING! properly installed to the vehicle. Inflate the The compact spare is for temporary emergency collapsible tire using the electric air pump be- Compact and collapsible spares are for tem- use only.
Your wheels are susceptible to deterioration Full Size Spare — If Equipped WARNING! caused by salt, sodium chloride, magnesium The full size spare is for temporary emergency chloride, calcium chloride, etc., and other road Limited use spares are for emergency use use only.
All passenger vehicle tires must conform Chrome Cleaner or their equivalent is recom- Dark Vapor Chrome, Black Satin Chrome, or Low mended or select a non-abrasive, non-acidic to Federal safety requirements in addi- Gloss Clear Coat Wheels cleaner for aluminum or chrome wheels. tion to these grades.
hicle Safety Standard No. 109. Grades B Traction Grades Temperature Grades and A represent higher levels of perfor- The Traction grades, from highest to low- The Temperature grades are A (the high- mance on the laboratory test wheel, than est, are AA, A, B, and C. These grades est), B, and C, representing the tire's the minimum required by law.
Tighten the lug nuts/bolts in a star pattern until WHEEL AND TIRE TORQUE WARNING! each nut/bolt has been tightened twice. Ensure SPECIFICATIONS that the socket is fully engaged on the lug To avoid the risk of forcing the vehicle off the nut/bolt (do not insert it halfway).
FLUIDS AND LUBRICANTS Engine Component Fluid, Lubricant, or Genuine Part We recommend you use Mopar Antifreeze/Coolant 10 Year/150,000 Mile Engine Coolant Formula OAT (Organic Additive Technology). We recommend you use API Certified SAE 5W-20 Engine Oil, meeting the Engine Oil requirements of FCA Material Standard MS-6395 such as Mopar, Pennzoil, and Shell Helix.
We recommend you use Mopar Power Steering Fluid + 4, or Mopar ATF+4 Automatic Transmission Power Steering Reservoir Fluid. • In choosing Authentic Accessories you gain • For the full line of Authentic Dodge Accesso- MOPAR ACCESSORIES far more than expressive style, premium pro- ries by Mopar, visit your local dealership or tection, or extreme entertainment, you also online at mopar.com for U.S.
Page 170
EXTERIOR: • Fog Lights • Molded Splash Guards • Front Air Deflector • Hitch Receiver INTERIOR: • Cargo Tray • Slush Mats • Door Sill Guards • Premium Carpet Floor Mats • Katzkin Leather Interiors ELECTRONICS: • Park Assist • Mopar Web (Wi-Fi) •...
The risk of unauthorized and unlawful access to CYBERSECURITY NOTE: your vehicle systems may still exist, even if the • FCA or your dealer may contact you directly Your vehicle may be a connected vehicle and most recent version of vehicle software (such as regarding software updates.
RADIO 4.3 & 4.3S Radio 4.3 & 4.3S At A Glance Radio 4.3 & 4.3S 1 — Radio: AM/FM/SIRIUS Satellite Radio (If Equipped) 2 — Status Bar 3 — Settings: Clock, Display, etc. 4 — Screen OFF/ON 5 — MORE: Uconnect Phone, Compass, Etc. 6 —...
Page 173
Displaying The Time Audio Settings Balance/Fade • If the time is not currently displayed at the top • Push the SETTINGS button on the faceplate • Press the “Balance/Fade” button on the of the screen when in Radio mode, push the on the right side of the unit.
Radio 4.3 & 4.3S Radio 4.3 & 4.3S 1 — Radio Station Presets 5 — Audio Settings 2 — View All Presets 6 — Direct Tune Radio Station 3 — Seek Up 7 — Radio Band 4 — Channel/Station Information 8 —...
Page 175
• To access the Radio mode, push the RADIO Store Radio Presets Manually button on the upper left side of the faceplate. Your radio can store 12 total preset stations. They are shown at the top of your screen. To see Selecting Radio Stations all 12 stations, press the “All”...
Media 4.3 & 4.3S Radio 4.3 & 4.3S 1 — Music Source 2 — More: Audio Settings And Shuffle 3 — Current Track Information 4 — Play/Pause 5 — Source: Disc, iPod, AUX Or Bluetooth 6 — Browse Music By: Folder, Artist, Playlist, Song, Album Or Genre...
Page 177
• The iPod/CD/AUX controls are accessed by NOTE: pushing the PLAYER button on the faceplate Uconnect will usually automatically switch to to enter the Player main screen, then press the the appropriate mode when something is first “Source” button on the touchscreen and connected or inserted into the system.
UCONNECT 3/3 NAV WITH 8.4–INCH DISPLAY Uconnect 3/3 NAV At A Glance Uconnect 3/3 NAV 1 — Status Bar 6 — Climate Control Button 2 — Small Navigation Map (Uconnect 3 NAV) 7 — Controls Button 3 — More Settings Button 8 —...
Page 179
• Press “+” or “–” next to Set Time Hours and Displaying The Time Equalizer Set Time Minutes to adjust the time. • If the time is not currently displayed on the • Press the “Equalizer” button on the touch- radio or player main page, press the “More”...
Radio Uconnect 3/3 NAV Uconnect 3/3 NAV 1 — Radio Station Presets 5 — Seek Down Button 2 — Toggle Presets 1–6 and 7–12 6 — Direct Tune To A Radio Station 3 — Radio Band Buttons 7 — Seek Up Button 4 —...
• To access the Radio mode, push the “Radio” Store Radio Presets Manually Media button on the touchscreen at the lower left of Your radio can store 12 total preset stations. Uconnect 3/3 NAV the screen. They are shown at the top of your screen. To see all 12 stations, press the “arrow”...
• The iPod/USB, CD, Audio Jack, SD Card or When making a selection, scroll up or down UCONNECT SETTINGS Bluetooth source is accessed by pressing the until the preferred setting is highlighted, then • The Radio 4.3/4.3 S and Uconnect 3/3 NAV “Player”...
• The functions of the portable device are con- STEERING WHEEL AUDIO Right Switch trolled using the device buttons. The volume • Push the switch up or down to increase or CONTROLS may be controlled using the radio or portable decrease the volume.
VIDEO ENTERTAINMENT SYSTEM NOTE: SD Card (3/3 NAV Only) • When connecting your iPod device for the first • Play songs stored on an SD card inserted into (VES) time, the system may take several minutes to the SD card slot, located on the radio face- read your music, depending on the number of plate.
Operation Of The Remote Auxiliary Audio/Video Input Jacks Navigation Overview • The Aux jacks are located on the rear of the The remote control operates similarly to any Uconnect 3/3 NAV With 8.4–inch Display Radio center console. DVD remote you have used before and allows integrates Garmin’s consumer-friendly naviga- the rear seat passengers to change stations, tion into your vehicle.
Main Navigation Menu Main Navigation Menu Touchscreen 1 — Where To? Button 4 — Tools Button 2 — View Map Button 5 — Detour Button 3 — Settings Button 6 — Stop Button...
Page 187
Acquiring Satellites Finding A Place By Spelling The Name Setting Or Changing Your Home Location • The GPS Satellite strength bars indicate the • From the Main Navigation Menu press “Where • Press the “Nav” button on the touchscreen in strength of your satellite reception.
Following Your Route Following Your Route 1 — Distance To Next Turn 6 — Press And Drag Map 2 — Current Location 7 — Your Location On The Map 3 — Zoom In Button 8 — Estimated Time Of Arrival 4 —...
• Your route is marked with a magenta line on NOTE: the map. If you depart from the original route, If the route you are currently taking is the only your route is recalculated. A speed limit icon reasonable option, the device might not calcu- could appear as you travel on major roadways.
• Models 3/3 NAV: Press the “Phone” button on UCONNECT PHONE Pairing A Phone the touchscreen and then the “Settings” but- • To use the Uconnect Phone feature, you must ton on the touchscreen. Next, press “Add Uconnect Phone (Bluetooth Hands Free first pair your Bluetooth phone with the Device.”...
Page 191
Start Pairing Procedure On Mobile Phone NOTE: Keep in mind that software updates – either on • Search for available devices on your Bluetooth your phone or Uconnect system – may interfere enabled mobile phone. This is usually within with the Bluetooth connection. If this happens, Settings or Options under “Bluetooth.”...
Page 192
Phone Menu Screen — Radio 4.3 & 4.3S 1 — Redial Last Number 7 — Manage Paired Phones 2 — Phone Signal 8 — Conference Call 3 — Current Phone 9 — Direct Dial 4 — Phone Battery Level 10 — Recent Call List 5 —...
Page 193
Phone Menu Screen — Uconnect 3/3 NAV 1 — Favorite Phonebook Entries 8 — Manage Paired Phones 2 — Phone Battery Level 9 — SMS (text messaging) 3 — Current Phone 10 — Direct Dial 4 — Phone Signal 11 — Recent Call List 5 —...
• Favorite phonebook entries can be saved as Making A Phone Call Mute (Or Unmute) Microphone During Call Favorites for quicker access. Favorites are • During a call, press the “mute” button on the To begin a phone call using Uconnect Voice shown at the top of your main phone screen.
NOTE: NOTE: General Information To access help, press the Uconnect Phone • For mobile phone compatibility and pairing in- The following regulatory statement applies to all button on the steering wheel and say "help." structions, please visit UconnectPhone.com. Radio Frequency (RF) devices equipped in this Press the display or push either vehicle: •...
UCONNECT VOICE COMMAND Changing The Volume “Show fuel prices” SiriusXM “Show movie listings” Travel Link (3/3 NAV ONLY) • Start a dialogue by pressing the Voice Com- “Show current weather” mand button , then say a command (for “Show extended weather” •...
Page 197
• Locating an address can be given as a one The following chart lists the navigation voice WARNING! commands that may be available. shot entry. For example, after saying “Find Address” and the system is ready, you can say Any voice commanded system should be Navigation Voice Commands: the entire address in one command, used only in safe driving conditions following...
Any communication to the manufacturer's cus- IF YOU NEED ASSISTANCE In Mexico Contact tomer center should include the following infor- Av. Prolongacion Paseo de la Reforma, 1240 The manufacturer and its authorized dealer are mation: vitally interested in your satisfaction. We want Sante Fe C.P.
Vehicle Limited Warranty expires. The manufac- We appreciate that you have made a major Customer Assistance For The Hearing Or turer stands behind only the manufacturer's ser- investment when you purchased the vehicle. An Speech Impaired (TDD/TTY) vice contracts. If you purchased a manufacturer's authorized dealer has also made a major invest- To assist customers who have hearing difficul- service contract, you will receive Plan Provisions...
Adminis- If you believe that your vehicle has a www.dodge.com scroll to the bottom of the trator, NHTSA, 1200 New Jersey Av- page and select the “Contact Us” link, then defect that could cause a crash or cause select the “Owner’s Manual and Glove Com-...
Need help?
Do you have a question about the JOURNEY 2019 and is the answer not in the manual?
Questions and answers
Can the outlet feature be turned on without the touch screen. Screen is non operational . Need access to charger and outlets
Yes, the power outlets in the 2019 Dodge Journey can be activated when the ignition is in the ON/RUN or ACC position, without using the touch screen.
This answer is automatically generated