TREELINE FDR0070AS Owner's Manual

Hanging feeder

Hide thumbs

Table of Contents

Quick Links

Download this manual

ASSEMBLY AND OPERATING IN STRUC TIONS

SAVE THIS MANUAL FOR FUTURE REFERENCE

NOTICE TO INSTALLER:

LEAVE THESE INSTRUCTIONS

WITH THE FEEDER OWNER FOR

FUTURE REFERENCE .

FDR0070AS_OM.indd Cov1

HANGING FEEDER

OWNER'S MANUAL

Model FDR0070AS

1/11/2023 9:18:03 AM

Table of Contents

Need help?

Do you have a question about the FDR0070AS and is the answer not in the manual?

Questions and answers

Summary of Contents for TREELINE FDR0070AS

Page 1 HANGING FEEDER OWNER’S MANUAL ASSEMBLY AND OPERATING IN STRUC TIONS SAVE THIS MANUAL FOR FUTURE REFERENCE Model FDR0070AS NOTICE TO INSTALLER: LEAVE THESE INSTRUCTIONS WITH THE FEEDER OWNER FOR FUTURE REFERENCE . FDR0070AS_OM.indd Cov1 FDR0070AS_OM.indd Cov1 1/11/2023 9:18:03 AM 1/11/2023 9:18:03 AM...
Page 2 IMPORTANT SAFETY WARNINGS WE WANT YOU TO ASSEMBLE AND USE YOUR FEEDER AS SAFELY AS POSSIBLE. THE PURPOSE OF THIS SAFETY ALERT SYMBOL IS TO ATTRACT YOUR ATTENTION TO POSSIBLE HAZARDS AS YOU ASSEMBLE AND USE YOUR FEEDER. WHEN YOU SEE THE SAFETY ALERT SYMBOL, PAY CLOSE ATTENTION TO THE INFORMATION WHICH FOLLOWS! READ ALL SAFETY WARNINGS AND INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING AND OPERATING YOUR FEEDER.
Page 3 ASSEMBLY INSTRUCTIONS READ ALL SAFETY WARNINGS & ASSEMBLY INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING OR OPERATING YOUR FEEDER. FOR MISSING PARTS, PLEASE CALL CUSTOMER SERVICE AT 855-735-9922. Inspect contents of the box to ensure all parts are included and undamaged. We recommend two people work together when as sem bling this unit. The following tools are required (not included) to assemble this Hanging Feeder: •...
Page 4 Choose a good, cleared assembly area and get a friend to help you put your feeder together. Lay card board down to protect feeder finish and assembly area. Step 1 Attach upper body to lower body using six M6 x 15 mm hex bolts and M6 stainless steel washers.
Page 5 Step 3 Attach two spring latches to feeder body using two M6 x 15 mm hex bolts, rubber washers, four M6 stainless steel washers and two M6 nuts. Attach the lid and secure with spring latches. Rubber Washer M6 Stainless Steel Washers HANGING FEEDER ASSEMBLED FDR0070AS_OM.indd 5...
Page 6 MOUNTING YOUR HANGING FEEDER Mounting on T-Post 1. Align notches in T-Post with slots on upper and lower mounting brackets. 2. Secure feeder to T-Post with T-Post clamps using four M8 x 18 mm hex bolts and M8 stainless steel washers. Note: The proper distance between the ground and the feeder spout should be between 30 to 36 inches.
Page 7 OPERATING IN STRUC TIONS READ ALL SAFETY WARNINGS AND INSTRUCTIONS CAREFULLY BEFORE OPERATING YOUR FEEDER. • Remove lid and pour feed into hanging feeder interior. Loading Your Feeder • After filling, replace lid and secure with spring latches. • Adjust the rate of feed by adjusting the feed gate using the two wing nuts.
Page 8 APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE. ©2022 The Boltz Group LLC. OM0070AS Owner’s Manual for Model Carrollton, Texas 75006 U.S.A. 0123 www.evenembers.com FDR0070AS FDR0070AS_OM.indd 8 FDR0070AS_OM.indd 8 1/11/2023 9:18:06 AM 1/11/2023 9:18:06 AM...