Sealey SM3002ST Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Indoor use only
instructions
1. SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this bench.
‰
Locate bench in a suitable work area.
9
Keep the work area clean, uncluttered and ensure there is adequate lighting.
9
WARNING! Use bench on level and solid ground, preferably concrete.
‰
Keep the bench clean and tidy in accordance with good workshop practice.
9
Keep children and unauthorised persons away from the work area.
9
DO NOT use the bench for any purpose other than that for which it is designed.
8
DO NOT undertake work on the bench without the workpiece being adequately secured. Use clamps or a vice (not included) to secure
8
the workpiece - available from your Sealey dealer.
DO NOT use the bench outdoors.
8
DO NOT get the bench wet or use in damp or wet locations or areas where there is condensation.
8
DO NOT exceed the maximum load for the work surfaces, worktop and bottom shelf - 100kg each, drawer - 20kg. Avoid heavy
8
impacts when placing objects onto the surfaces.
DO NOT clean the bench with any solvents which may damage the surface or the protective coating on the worktop.
8
2. INTRODUCTION
Floor stand with sliding tool shelf suitable for SM2502, SM2503 & SM3002. (Not included)
3. CONTENTS
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . SM3002ST
1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pad
2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Foot (I)
3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sliding shelf
4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Slide rail (left)
5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Lock washer
6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Screw (M6x16)
7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Washer
8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Nut (M6)
9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stand top
10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Support
11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Slide rail (right)
12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Supporting bar
13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Foot (II)
4. ASSEMBLY
NOTE: Items 3, 4 , 10 and 11 are pre-assembled.
4.1.
Lay item 9 flat on the ground with the pre-drilled holes uppermost.
4.2. Position item 10 onto item 9 such that the holes in the support (item 10) align
with the pre-drilled holes in item 9. Secure item 10 to item 9 using the self
tapping screws provided.
4.3. Attach items 2 and 13 to item 10 using the bolts, washers, lock washers and
nuts provided (items 6, 7, 5 and 8).
4.4. Insert item 12, ensuring the correct orientation, as shown in (fig.1) and secure using
the bolts, washers, lock washers and nuts provided (items 6, 7, 5 and 8).
4.5. Attach items 1 to items 2 and 13, invert the stand and it is ready for use.
5. MAINTENANCE
DO NOT clean the bench with any solvents which may damage the surface or the protective coating on the worktop.
8
5.1. Wipe clean after use.
© Jack Sealey Limited
MACHINE STAND
SM3002ST
MODEL NO:
Original Language Version SM3002ST | Issue 2 (H,F,1) 01/02/2019
fig.1