Sealey SNA9821 Quick Start Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instruction protection
manual
1. SAFETY
WARNING! Isolate the drill from the electrical supply before connecting or disconnecting nibbler
‰
attachment.
Ensure all safety instructions supplied with the drill to be used, are adhered too, in addition to these safety instructions.
9
Maintain the nibbler attachment in good condition.
9
Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be
9
dangerous and will invalidate the warranty.
Maintain correct balance and footing. Ensure that the floor is not slippery and wear non-slip shoes.
9
Keep children and unauthorised persons away from the work area.
9
Evaluate the work area before using the attachment.
9
Secure loose work-pieces with a clamp, vice or other adequate holding device. DO NOT hold
9
work-piece in your hand.
Avoid unintentional starting of the drill.
9
Wear approved safety eye protection (standard spectacles are not adequate).
9
Remove ill fitting clothing. Remove ties, watches, rings, any loose jewellery and contain long hair.
9
DO NOT use the nibbler attachment where there are flammable liquids, solids or gases such as paint solvents, etc.
8
DO NOT allow children to operate the nibbler attachment.
8
DO NOT operate the nibbler attachment if any parts are missing as this may cause failure or possible personal injury.
8
DO NOT use the nibbler attachment for a task it is not designed to perform.
8
DO NOT operate the drill and nibbler attachment when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT exceed the capacities shown below, for the material to be cut.
8
Familiarise yourself with the application and limitations of the nibbler attachment, as well as the
9
specific hazards.
When not in use, disconnect from the drill and store in a safe, dry childproof location.
9
2. INTRODUCTION
Turns an electric or air drill into a versatile nibbler suitable for cutting intricate shapes in various materials. Double end punch allows
handle to be removed and re-attached to opposite side for longer periods of use.
3. SPECIFICATION
Model No........................................................: ..............................................................SNA9821
Consumable Parts: ............................................................SNA9821P - Punch, SNA9821D - Die
Maximum Capacity: ............Steel; 1.6mm, Stainless Steel; 1.2mm, Brass, Plastic, Copper; 2mm
Maximum Speed:............................................................................................................3000rpm
4. OPERATION
4.1. Attach the nibbler to a suitable drill by inserting the drive into the drill chuck and tightening the chuck.
4.2. Attach handle to the nibbler as shown (fig.1).
4.3. Secure the work-piece in a suitable clamp or vice, ensuring there is at least a 15mm clearance underneath the area of material to be cut.
4.4. Plug the drill into the supply, first ensuring it is turned off.
4.5. Securely hold the nibbler attachment handle and the drill, switch the drill on.
4.6. Carefully move the nibbler attachment towards the starting point of the desired cut and engage nibbler head with the material, start to cut
into the material.
4.7. Carry on cutting through the material as desired, keeping the nibbler attachment at a right angle to the material. When finished cutting,
move the nibbler head away from the material before switching off the drill.
© Jack Sealey Limited
DRILL NIBBLER ATTACHMENT
SNA9821
MODEL NO:
Wear ear
Wear a mask
protection
Original Language Version
SPECIFICATION
SNA9821 Issue:1 05/07/23