PATPET p-collar 360 - Dog Training Collar Manual

The dog training collar is designed to let dogs live safely, happily and get along with people more harmoniously.

Do not use with aggressive dogs.
Aggressive dogs can cause severe injury and even death to their owner and others. If you are unsure whether this product is appropriate for your dog, please consult your veterinarian or certified trainer.

Safety during on-leash training.
It is vitally important that you and your dog remain safe while learning during on-leash training. Your dog should be on a strong leash, long enough for him to attempt to chase an object, but short enough for him not to reach a road or other unsafe area. You must also be physically strong enough to restrain your dog when he tries to chase.

Risk of skin damage.
Please read and follow the instructions in this manual. Proper fit of the collar is important. A collar worn for too long or made too tight on the pet's neck may cause skin damage ranging from redness to pressure ulcers. This condition is commonly known as bed sores.

• Avoid leaving the collar on the dog for more than 12 hours per day.
• When possible reposition the collar on the pet's neck every 1 to 2 hours.
• Never connect a lead to the electronic collar; it will cause excessive pressure on the contacts.
• lf a rash or sore is found, Stop using the collar until the skin has healed.
• If the condition persists over 48 hours, see your veterinarian.
• This product is nota toy, please keep away from children.
• This product is only used for healthy dogs.

Overview

Remote

1. Signal LED
2. Level +
3. Level -
4. On/Off Button
5. Tone Button
6. Vibration Button
7. Shock Button
8. Battery Display
9. Dog 1 or dog 2 mode
10. Switch dog 1 or dog 2 mode
11. Level Display
12. Charging Port
13. Hook&Loop Bandage

Receiver Collar

1. Indicator light
2. On/Off Button
3. Contact Points
4. Charging Port (with cover)

Setting Up the Product

Before you can use the Dog Training Collar, you must set up the product as below steps

1. Charging the Remote and the Receiver Collar.
2. Prepare the Remote and turn it on.
3. Prepare the Receiver Collar and turn it on.
4. Function test, test function of buttons before wearing it on dog.
5. How to use the Test Lamp, test Shock function.
6. Pair the Remote and the Receiver Collar, pair them when the product lose its code or pair for a second collar.

Charging the Remote and the Receiver Collar

1. Plugin and fully charge the Remote and the Receiver collar.
   For the initial charge, be sure to charge it for 4 hours.
   Subsequent charges only take 2-3 hours.
2. When full charged, the red LED on the Receiver Collar will become green. The Battery Display of the Remote will stop cycling and appear full.
3. Please replace the rubber cover when the Receiver Collar is full charged.

Tips:

1. Excessive charging will shorten battery life. Only charge them when batteries are low.
2. When you're not using the collar, please turn it off to increase the battery life.

Note:
Please use the Output: DC 5V 500-800mA charger to charge the product.
Don't use a charger that does not meet the specifications to charge the product.

Prepare the Remote

Turn ON/OFF the Remote

1. Long press the ON/OFF button to turn the remote ON.
2. LCD will be lighted, and show the information of current channel, battery power and levels. If not, please charge the remote.
3. Long press the ON/OFF button to turn the remote OFF.

We send a Hook&Loop Bandage, you can hang the remote on your arm for easy carrying.

Prepare the Receiver

Assembly Collar

Please refer to the picture to wear the collar on the dog's neck.

Turn on the Receiver Collar

• Press the On/Off Button the Green LED light is on.
• In normal mode, the Green LED will flash every 4 seconds, indicating the Receiver Collar is on and ready to receive a signal from the Remote.

Turn off the Receiver Collar

Press and hold the On/Off Button until the Red LED light shuts off (This takes approximately 3 seconds).

NOTE:
To extend the life span of the batteries, please turn the Receiver Collar off when it is not in use.

Function Test

We recommend you experience firsthand how the different levels feel on yourself and always begin at the lowest level, increase to a level that makes you personally comfortable.

1. Place one finger on two contact Points of the training collar.
2. Hold your remote approximately 2 ft. away from the training collar.
   Press the Vibration Button continuously for 1 to 2 seconds.
   You should feel continuous vibration.
3. Press to decrease levels. Starting at level 1,press the Shock Button.
4. Increase the level until the sensation begins to feel uncomfortable.

NOTE: Continuous stimulation will transmit for no more than 10 consecutive seconds. To reactivate, release and repress the button.

	Tone: sends atone with non-adjustable level to the Receiver Collar.
	Vibration: sends a vibration with non-adjustable level to the Receiver Collar.
	Shock: sends 0-16 adjustable levels of static stimulation to the Receiver Collar.
	Slide up, control dog 1, slide down, control dog 2.
	Long press to turn on, long press to turn off.
	Press to increase the Shock Level.
	Press to decrease the Shock Level.

Note:

• The Shock Level can be adjusted from 1 to 16 levels, please adjust it properly according to your dog's reaction at each level.
• It is not recommended to press and hold the Vibration/Shock Button too long to avoid physical or psychological hurt to the dog.

How to Use the Test Lamp

Shock Function Test

1. Turn on the Receiver Collar.
2. Hold the Test Lamp contacts against the Contact Points.
3. Press the Shock Button and the Test Lamp will be lighted. It will be brighter accordingly with the Shock Level increasing.
   

Pair the Remote and the Receiver Collar

1. Use the switch on the Remote to select Dog 1.
2. With the Remote turned on and the Receiver Collar turned off, press and hold the ON/OFF Button on the Receiver Collar for 4-5 seconds.
3. The Red & Green LED will blink for about 10 seconds indicating that it is ready for pairing.
4. Press and hold Tone Button and Vibration Button at the same time for 2-3 seconds, the Green LED on the Receiver Collar will blink for 5 times indicating successful pairing.

Pairing a Second Collar with the Remote

Use the switch on the Remote to select Dog 2.
Then follow the pairing steps above from 2-4.

Dog Training

Selecting The Contact Points and The Contact spring sheet

For the best results, select the correct Contact Points based on your dog's coat.
You can use the Contact point separately, or use the Contact point and spring at the same time.

Collar Fitting

Please fit the collar properly so that the Contact Points press firmly against the dog's skin. When properly fitted, you should be able to put a finger between the Receiver Collar and dog's neck.

Too loose: The Receiver Collar will move around the dog's neck, the Contact Points may hurt the dog's skin.

Too tight: It may cause dog's to breathe hard.

1. Do not shave the pet's neck as this may increase the risk of skin irritation.
2. The collar should not be worn for more than 12 hours per day. Or it may cause skin irritation.

Find the Best Shock Level for Your Pet

The unit comes with Up and Down buttons to control the Shock Level, with Level 1 being the lowest level and Level 16 being the highest. The most suitable shock level for your dog depends on your dog's temperament and threshold for Shock. Always start at the lowest level and work your way up. The appropriate level can be found when the dog responds to the Shock with a mild reaction, such asa flick of the ear, a lick of the lips, a tensing of the neck muscles etc. The Shock Level may vary depending on the training situation. When highly distracted, The dog will require a higher level of Shock.

Device Information

Product Specification

The unit need to be charged under any of below situations

1. The indicator light on the Receiver Collar is emitting a red color every 4 seconds or flashes rapidly.
2. The 3 bar indicator on the Remote LCD shows just 1 bar.
3. The indicator light on the Remote or Receiver Collar will not come on.
4. The indicator light on the Remote or Receiver Collar comes on momentarily when any of the Mode Buttons is pressed.

Frequently Asked Questions

Troubleshooting Guide

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download PATPET p-collar 360 - Dog Training Collar Manual