Byron Home Easy HE-200, HE-210, HE-220 - Remote Control Timer Manual

Also See for Home Easy HE-200:

Installation instructions (2 pages)

Installation manual (2 pages)

Table of Contents

Contents

1 Introduction
2 Display Functions
3 Pairing/Deleting with Remote Control
- 3.1 Deleting Remote Control
- 3.2 Remote Socket reset
4 Unit Setting
5 Dimming Receiver Sockets HE220
6 Changing Batteries
7 Product Specification
8 Switching On/Off
9 Setting Clock
10 Setting Timer
11 Help Section
12 Range Reduction Guide
13 Documents / Resources
- 13.1 References
- 13.2 Download manual

Byron Home Easy HE-200, HE-210, HE-220 - Remote Control Timer Manual

Introduction

RE-INVENTING THE HOME

The HomeEasy remote control Timer allows you to add the following extra features to your HomeEasy products:

12 Programmable memory Settings
Security Mode
Single and Daily Timer Functions
24Hr Timer Display
30 Metre Wire Free Range
CR2032/23A Battery (Included)

Display Functions

LCD Display

12 Programmable Memory Spaces
24Hr Time
Timer Setting "On"
Timer Setting "Off"
Security Mode
Timer Mode - Single Timer Setting
Timer Mode - Daily Timer Setting
Low Battery Warning
Unit Code Display
Transmission Indicator Signal

	Receiver Select
	Switch "On" Selected Receiver
	Switch "Off" Selected Receiver
	Clock Setting
	Program Timer/View
	Enter
	Delete/Pause
	Select Up/Down

Pairing/Deleting with Remote Control

Up to Six remote control units can be paired with each receiver socket or module. To program a socket insert the unit into a plug socket and switch on the power, now press the "Learn" button. The LED will start to flash, now press the selected "ON" button on the remote control, the LED will stop flashing. The units are now paired together, you can test this by pressing the selected "ON/OFF" button
Pairing/Deleting with Remote Control
Always refer to the original instruction when using with additional products

Deleting Remote Control

To delete a remote control that has been paired with a HomeEasy receiver socket, simply press the "Learn" button. The LED will start to blink; press the "Off" button on the remote control, the LED will blink twice to confirm that the remote control has been removed from the receiver sockets memory.

Remote Socket reset

To delete all the remote control units from the memory of the receiver socket, hold the "Learn" button for more than 6 seconds, the LED will start to blink continuously. Press the learn button again, the LED will blink twice to confirm the deletion of all remote controls form the receiver memory.

Unit Setting

The HE-200 Remote Control Timer can be paired to 16 separate receiver units, select the unit code by pressing the unit button.

The HE-200 comes with a preset to Group code A. When using additional remote control timers you will need to select a new group code.

To select a new group code, remove the battery cover and using a small screw driver, rotate the group dial to a new setting e.g. Group B

Dimming Receiver Sockets HE220

To dim a compatible receiver socket.

Select the unit by pressing the "unit" button until the correct number is displayed on the screen.
Press the "On" button and then press "On" again.
Never exceed 300W maximum load. HE210 & HE-220
The dimmer will start to dim the light unit till it reaches zero, then the unit will start to increase the light up to the maximum level. To set the desired level, press the "On" button.
Press the "Off" button to switch the receiver unit off.

Changing Batteries

Remove the battery cover form the back of the remote control.

The HE-200 includes 2 batteries:

LCD Display: 1 x CR2032 -Byron SX100 (Included)
RF Transmission: 1 x 23A - Byron SD100 (Included)

Remove the required battery and replace with new, making sure the polarity matches the internal markings.

Product Specification

Remote Control: HE-200
Battery: 3v Cr2032 & 12V 23A
Range: 30 Metres (Open Distance)
Frequency: 433.92MHz Indoor Use Only
Receiver Socket: HE-202
Input: 230V ~ 50Hz
Max Load: 300W (Incandescent)
Frequency: 433.92MHz
Indoor Use Only

Warning: Never Exceed the Product Specification

Switching On/Off

Select the unit by pressing the "unit" button until the correct number is displayed on the screen.
Press the "On" button, the receiver socket will switch on.
Never exceed 300W maximum load.
Press the "Off" button to switch the receiver unit off.

Setting Clock

The remote control displays the time in a 24hr format, to set the time.

Press and hold the clock button for +3sec. The hrs will now start to flash
Use the buttons to select the hours and press Enter.
The minutes will now start to flash, set using the up and down arrows to select the minutes and then press enter.

Setting Timer

The HE-200 remote control timer can store up to 12 different timer programs, ideal for switching on lights throughout the home for added security.
Setting Timer

To program the remote control:

Press and hold the "Timer" button for 3 seconds, the display will show the 12 available memory spaces. Use the arrows keys to select a memory space, the display will also show any programmed times already saved. Press "Enter" to select the program space.
Select the required unit from using the "Up/Down" arrows e.g. if the socket to be programmed is programmed to unit code 2, select unit 2 on the display and press "Enter". Only one unit code can be selected per program.
The start or On time will start to flash, use the arrow keys to select the hours and press enter to select the min. Now select the finish or off time.
Finally select the program mode using the arrows keys and press enter to confirm.

Daily Timer Setting

Activates the program daily

Security Setting

Selecting the security mode will switch the receiver units "On/Off" randomly through out the set time.

On = between 40Min - 2Hrs
Off = between 40Min - 3Hrs

Single Timer

Activates the program for a single time only.

Help Section

Help: Occasionally interference from receiver sockets plugged into adjacent wall sockets or when used with transformers (low voltage products) can affect the operating range.
Try placing one of the receiver sockets in another wall socket. For low voltage products, place the transformer as far away form the receiver socket as possible.

RF Range: The radio signals operating distance is reduced when the signal has to pass through walls. The radio signals achieve a range of 30m inside a building; this can be reduced depending on the type of material