Craftsman 917.20403 Operator's Manual page 29

OPERACIÓN
Estos símbolos pueden aparecer sobre su tractor o en la literatura proporcionada con el producto.
Aprenda y comprenda sus significados.
MARCHA NEUTRO ALTO BAJO POSICIÓN DE ARRANQUE
ATRÁS
MOTOR MOTOR MOTOR EL CIERRE
APAGADO EN MARCHA ENCENDIDO DIFERENCIAL
SISTEMA MARCHA MARCHA PALANCA DE
FUNCIONAMIENTO ATRÁS HACIA MANDO CRUCERO
ATRÁS (ROS) ADELANTE
ACCESORIO ACCESORIO PELIGRO, GUARDE
DEL EMBRAGUE DEL EMBRAGUE LAS MANOS Y
ENGANCHADO DESENGANCHADO LOS PIES LEJOS
RUEDA LIBRE
(Solamente para los
modelos automatico)
No seguir las siguientes
instrucciones puede provocar
heridas o muerte. Los símbolos
de aviso de seguridadse utilizan
para identificar informaciones de
seguridad relativas a peligros que
pueden provocar la muerte, heridas
graves y/o daños a la máquina.
RÁPIDO LENTO
EN CLIMA FRÍO
PEDAL DE FRENO DE
ALTURA
FRENO / ESTACION-
DE LA
EMBRAGUE AMIENTO
SEGADORA
LUCES COMBUS- BATERÍA
ENSENDIDAS TIBLE
15
MANTENGA EL PELIGROS DE
AREA DESPEJADA PENDIENTES
(VEA LA SECCIÓN DE LAS REGLAS DE SEGURIDAD)
PELIGRO indica un peligro que, si no se evita,
provoca muerte o lesiones graves.
ADVERTENCIA indica un peligro que, si no se evita,
puede provocar muerte o lesiones graves.
PRECAUCIÓN indica un peligro que, si no se evita,
puede provocar lesiones ligeras o moderadas.
PRECAUCIÓN cuando se utiliza sin el símbolo de
aviso, indica una situación que puede provocar
daños al tractor y/o al motor.
SUPERFICIES CALIENTES indica un peligro que,
si no se evita, puede provocar la muerte, lesiones
graves y/o danos a la máquina.
FUEGO indica un peligro que, si no se evita, puede
provocar la muerte, lesiones graves y/o danos
a la máquina.
52
TO LEVEL MOWER
Ensure tires are properly inflated to the PSI
shown on tires. If tires are over or under
inflated, it may affect the appearance of your
lawn and lead you to think the mower is not
adjusted properly.
VISUAL SIDE-TO-SIDE ADJUSTMENT
1. With all tires properly inflated and if your
INTERRUPTOR
lawn appears unevenly cut, determine
DE ARRANQUE
SmartSwitch™
which side of mower is cutting lower.
NOTE: As desired, you can raise the low
side of mower or lower the high side.
2. Go to side of mower you wish to adjust.
LEVANTA-
MIENTO DE
3. With a 3/4" or adjustable wrench, turn
LA SEGADORA
lift link adjustment nut (A) to the left to
lower the mower, or, to the right to raise
the mower.
PROTECCIÓN
DE OÍDO SE
REQUIERE
15
Turn nut
right to
raise
mower
NOTE: Each full turn of adjustment nut will
change mower height about 3/16" (4,7 mm).
4. Test your adjustment by mowing some
uncut grass and visually checking the
appearance. Readjust, if necessary, until
you are satisfied with the results.
PRECISION SIDE-TO-SIDE ADJUSTMENT
1. With all tires properly inflated, park tractor
on level ground or driveway.
CAUTION: Blades are sharp. Protect
your hands with gloves and/or wrap blade
with heavy cloth.
2. Raise mower to its highest position.
3. At both sides of mower, position blade
at side and measure distance "A" from
bottom edge of blade to ground. The dis-
tance should be the same on both sides.
4. If adjustment is necessary, see steps in
Visual Adjustment instructions above.
A
5. Recheck measurements; adjust if neces-
sary until both sides are equal.
FRONT-TO-BACK ADJUSTMENT
IMPORTANT: Deck must be level side-
to-side.
To obtain the best cutting re sults, the mower
blades should be adjusted so the front tip
is 1/8 to 1/2" (3,1 to 12,7 mm) (lower than
the rear tip when the mower is in its highest
position.
CAUTION: Blades are sharp. Protect
your hands with gloves and/or wrap blade
with heavy cloth.
• Raise mower to highest position.
• Position any blade so the tip is pointing
straight forward. Measure distance "B" to
the ground at front and rear tip of blade.
A
B
• If front tip of blade is not 1/8 to 1/2" (3,1
to 12,7 mm) lower than the rear tip, go to
the front of tractor.
• With an 11/16" or adjustable wrench,
Turn nut loosen jam nut "A" several turns to clear
left to
adjustment nut "B".
lower
• With a 3/4" or adjustable wrench, turn
mower
front link adjustment nut "B" clockwise ( )
(tighten) to raise the front of mower, or,
counterclockwise ( ) (loosen) to lower
the front mower.
Tighten adjust
nut "B" to
raise mower
02950
Loosen jam nut "A" first
NOTE: Each full turn of adjustment nut will
change mower height about 1/8" (3,1 mm).
• Recheck measurements, adjust if neces-
sary until front tip of blade is 1/8 to 1/2"
(3,1 to 12,7 mm) lower than the rear tip.
• Hold adjustment nut in position with
wrench and tighten jam nut securely
A
against adjustment nut.
29
B
B
A
Loosen adjust
nut "B" to
lower mower