Holmes HCH4953, HCH4954 - Ultra Quiet Ceramic Heaters Manual

TECHNICAL SPECIFICATIONS

• Wattage: 1500W (+5% –15%)
• Working voltage: 120V AC/60Hz

AUTO SAFETY SHUT-OFF WITH CERAMIC CONTROL

This heater is equipped with a patented, technologicallyadvanced, safety system that requires the user to reset the heater if there is a potential overheat situation. When a potential overheat temperature is reached, the system will automatically shut the heater off. It can only resume operation when the user resets the unit.

To Reset the Heater:

1. Unplug the heater and wait 10 minutes for the unit to cool down.
2. After the 10 minutes, plug the unit in again and operate normally.

Tip-Over Protection:
When the heater is accidentally knocked over, it will automatically shut off. To reset, simply place the heater in an upright position.
Press the MODE/OFF button and operate normally.

PRE-OPERATING INSTRUCTIONS

1. Carefully remove your heater from the box. please save the carton for off-season storage.
2. Make sure the unit is in the OFF position before plugging the heater into the outlet.
3. Place heater on firm level surface.
4. Avoid overloading your circuit by not using other high wattage appliances in the same outlet. At 1500 watts, this unit draws 12.5 Amps.
   NOTE: The power light will remain lit while heater is plugged in.

Figure 1

1. MODE/OFF BUTTON
2. HIGH POWER
3. LOW POWER
4. SET TEMPERATURE LIGHTS

OPERATING INSTRUCTIONS

Your heater is equipped with a technologically advanced 1Touch^® electronic thermostat. You can set the heater to run continuously in manual mode or set the 1Touch^® Thermostat to your desired temperature setting. The 1Touch^® thermostat will automatically turn the heater ON or OFF depending on the preset comfort level. The comfort level ranges between 60° and 80°Fahrenheit. Manual Mode Instructions:

1. Plug the heater into a 120V AC electrical outlet.
2. To start the unit, push the MODE/OFF button once for the HIGH (HI) manual setting. (See Figure 1)
3. Press the button again for the LOW (LO) manual setting. (See Figure 1)
4. To stop the unit, press and hold the button for two seconds or keep pressing the button until all the temperature indicators are OFF.

1TOUCH^® THERMOSTAT INSTRUCTIONS

To take advantage of the 1Touch^® Thermostat continue to press the MODE/OFF button until the desired temperature is set in either the HIGH or LOW setting. When ambient temperature rises above the set temperature, the heater will stop. When the ambient temperature drops below the set temperature, the heater will turn on automatically.
NOTE: When the 1Touch^® thermostat is set, either the HIGH (HI) or LOW (LO) power light, and the temperature light will remain lit during operation. (See Figure 1)
NOTE: It is normal for the heater to cycle ON and OFF as it maintains the preset temperature. To prevent the unit from cycling, you need to raise the thermostat setting.
NOTE: 1Touch^® has memory. The 1Touch^® thermostat will remember the previous temperature setting after the unit has been turned off. However, if the unit is unplugged, the 1Touch^® thermostat will be reset and will no longer remember the previous temperature setting.

OSCILLATION INSTRUCTIONS (HCH4954 ONLY)

1. Select the desired control setting and press the oscillation button once to turn oscillation on.
2. To stop oscillation press the oscillation button (Osc.) again.
3. Please do not manually turn the unit; it is designed to turn only by motorized oscillation.

VIZIHEAT^TM COLOR CHANGING DISPLAY

Your heater features the revolutionary technology and safety of ViziHeat^TM Color Changing Display. As your heater warms up, the front grill will change color - a visual reminder that the grill is warm and the heater is on. The exact timing of the color change may vary. When the heater is turned off, the grill will return to its original color, thus indicating the grill is cool to the touch. NOTE: If unit is left in extreme cold temperatures (-22°F/ -30°C) the ViziHeat^TM Color Changing Display may not perform. The heater itself will function normally. Store heater in a cool and dry location.
NOTE: The ViziHeat^TM Color Changing Effect may wear off after heavy use of this heater. The heater will continue to operate normally.

CLEANING/MAINTENANCE

During Season Care:

1. Always unplug the heater before cleaning.
2. Clean the unit with a soft cloth moistened with a mild soap solution.
3. NEVER use abrasive or flammable solvents to clean the unit.
4. After cleaning, be sure to completely dry the unit with a cloth or towel.

After Season Care:

1. Store heater in a cool, dry location.
2. The manufacturer recommends that you store the unit in its original carton.

TROUBLESHOOTING

If your heater fails to operate

• UNPLUG THE UNIT.
• Make sure the electrical outlet or circuit breaker is working.
• Check for obstructions. If you find an obstruction turn the heater OFF, and unplug the unit. Carefully remove the obstruction and follow the reset instructions.

Please DO NOT attempt to open or repair the heater.
Please see the Warranty for Service Instructions.