Bosch 1 270 020 909 Original Instructions Manual page 22

OBJ_BUCH-2087-003.book Page 14 Friday, February 13, 2015 5:44 PM
English–14
Technical Data
Battery Charger
Article number
Rated voltage
Frequency
Output voltage
Charging current
Charging time
– PowerPack 300
– PowerPack 400
Number of battery cells
Operating temperature
Storage temperature
Weight according to
EPTA-Procedure 01/2003
Degree of protection
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Operation
Initial Operation
Connecting the charger to the mains (see figure E)
 Observe the mains voltage! The voltage of the power
supply must correspond with the data given on the name-
plate of the battery charger. Battery chargers marked with
230 V can also be operated with 220 V.
Plug the charger plug C3 of the power cord into the charger
socket C2 of the charger.
Connect the mains cable (country-specific) to the mains
supply.
Charging the removed battery (see figure F)
Switch the battery pack off and remove it from the holder of
the eBike. For this, read and observe the operating instruc-
tions of the battery pack.
 Place down the battery pack only on clean surfaces. In
particular, avoid soiling the charge socket and the con-
tacts, e.g. by means of sand or soil.
Insert the charger plug C5 of the battery charger into the
socket C6 on the battery pack.
0 276 001 SPI | (13.2.15)
Charging the battery on the Bike (see figure G)
Switch the battery off. Clean the cover of the charge socket
Charger
C7. Prevent especially the charge socket and the contacts
0 275 007 907
from getting dirty, e.g. by sand or soil. Lift the cover of the
charge socket C7 and plug the charge connector C5 into the
V~ 207 –264
charge socket C6.
Hz 47 –63
 Charge the battery only in accordance with all safety
V 36
instructions. If this is not possible, remove the battery
A 4
from the holder and charge it in a more suitable location.
When doing so, read and observe the operating instruc-
h 2.5
tions of the battery.
h 3.5
Charging Procedure
30 –40
The charging procedure begins as soon as the charger is con-
°C –5...+40
nected to the battery or the charge socket on the bike and the
°C –10...+50
main power supply.
Note: Charging is only possible if the temperature of the
kg 0.8
eBike battery is within the permitted charging temperature
IP 40
range.
Note: The drive unit is deactivated during the charging proce-
dure.
The battery can be charged with and without the on-board
computer. When charging without the on-board computer,
the charging procedure can be observed on the battery
charge-control indicator.
When the on-board computer is connected, the back lighting of
the display is switched on at low luminosity and "Charging/
xx% charged" appears on the display.
The on-board computer can be removed during the charging
procedure, or it can also be fitted after the charging proce-
dure has begun.
The charging state is displayed by the battery charge-control
indicator A3 on the battery and by the bars on the on-board
computer.
When charging the eBike battery on the bike, the battery of
the on-board computer can also be charged.
During the charging procedure, the LEDs of charge-control in-
dicator A3 on the battery pack light up. Each continuously lit
LED is equivalent to a charge capacity of approx. 20 %. The
flashing LED indicates the charging of the next 20 %.
 Use caution when touching the charger during the
charging procedure. Wear protective gloves. Especially
in high ambient temperatures, the charger can heat up
considerably.
Bosch eBike Systems