Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Siemens SINUMERIK ONE MCP 2200
Summary of Contents for Siemens SINUMERIK ONE MCP 2200
- Page 1 Fundamental safety instructions Overview Dimension drawings SINUMERIK Operator control and display elements SINUMERIK ONE ONE MCP Part 2: MCP 2200 Technical data Equipment Manual Valid for: Control system SINUMERIK ONE SINUMERIK 840D sl/840DE sl 11/2022 A5E50324703B AC...
- Page 2 Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems.
-
Page 3: Table Of Contents
Table of contents Fundamental safety instructions......................5 General safety instructions....................5 Equipment damage due to electric fields or electrostatic discharge ........9 Warranty and liability for application examples ..............10 Security information ......................11 Residual risks of power drive systems ................. 12 Overview.............................. - Page 4 Table of contents ONE MCP Part 2: MCP 2200 Equipment Manual, 11/2022, A5E50324703B AC...
-
Page 5: Fundamental Safety Instructions
Fundamental safety instructions General safety instructions WARNING Electric shock and danger to life due to other energy sources Touching live components can result in death or severe injury. • Only work on electrical devices when you are qualified for this job. •... - Page 6 Fundamental safety instructions 1.1 General safety instructions WARNING Electric shock due to equipment damage Improper handling may cause damage to equipment. For damaged devices, hazardous voltages can be present at the enclosure or at exposed components; if touched, this can result in death or severe injury.
- Page 7 • Therefore, if you move closer than 20 cm to the components, be sure to switch off radio devices, cellphones or WLAN devices. • Use the "SIEMENS Industry Online Support app" only on equipment that has already been switched off. WARNING...
- Page 8 Fundamental safety instructions 1.1 General safety instructions NOTICE Overheating due to inadmissible mounting position The device may overheat and therefore be damaged if mounted in an inadmissible position. • Only operate the device in admissible mounting positions. WARNING Unexpected movement of machines caused by inactive safety functions Inactive or non-adapted safety functions can trigger unexpected machine movements that may result in serious injury or death.
-
Page 9: Equipment Damage Due To Electric Fields Or Electrostatic Discharge
Fundamental safety instructions 1.2 Equipment damage due to electric fields or electrostatic discharge Equipment damage due to electric fields or electrostatic discharge Electrostatic sensitive devices (ESD) are individual components, integrated circuits, modules or devices that may be damaged by either electric fields or electrostatic discharge. NOTICE Equipment damage due to electric fields or electrostatic discharge Electric fields or electrostatic discharge can cause malfunctions through damaged individual... -
Page 10: Warranty And Liability For Application Examples
Fundamental safety instructions 1.3 Warranty and liability for application examples Warranty and liability for application examples Application examples are not binding and do not claim to be complete regarding configuration, equipment or any eventuality which may arise. Application examples do not represent specific customer solutions, but are only intended to provide support for typical tasks. -
Page 11: Security Information
Siemens’ products and solutions undergo continuous development to make them more secure. Siemens strongly recommends that product updates are applied as soon as they are available and that the latest product versions are used. Use of product versions that are no longer supported, and failure to apply the latest updates may increase customer’s exposure... -
Page 12: Residual Risks Of Power Drive Systems
Fundamental safety instructions 1.5 Residual risks of power drive systems Residual risks of power drive systems When assessing the machine- or system-related risk in accordance with the respective local regulations (e.g., EC Machinery Directive), the machine manufacturer or system installer must take into account the following residual risks emanating from the control and drive components of a drive system: 1. -
Page 13: Overview
Overview This manual describes the specific properties of the SINUMERIK ONE MCP 2200 machine control panel. The documentation is always structured in 2 parts. Part 1 contains general information that applies to all machine control panels. Part 2 covers specifics of individual machine control panels. - Page 14 Overview ONE MCP Part 2: MCP 2200 Equipment Manual, 11/2022, A5E50324703B AC...
-
Page 15: Dimension Drawings
Dimension drawings Required installation clearance 55 mm Figure 3-1 Front, rear and side view of MCP 2200 (all specifications in mm) ONE MCP Part 2: MCP 2200 Equipment Manual, 11/2022, A5E50324703B AC... - Page 16 Dimension drawings Panel cutout The MCP 2200 is secured using 16 M5 nuts. The tightening torque is 1.5 Nm. Use spring elements in addition to the M5 nuts. In the sealing area Figure 3-2 Panel cutout of MCP 2200 (all specifications in mm) ONE MCP Part 2: MCP 2200 Equipment Manual, 11/2022, A5E50324703B AC...
-
Page 17: Operator Control And Display Elements
Operator control and display elements Front side Overview ① Emergency stop button ② QWERTY keyboard ③ 4x mounting space for 22.5 mm elements with slide-in labels ④ Key-operated authorization switch ⑤ Powerride 1 (feed) + keypad 3.1 ⑥ Powerride 2 (spindle) + keypad 3.2 ⑦... -
Page 18: Rear Side
Operator control and display elements 4.2 Rear side Rear side ① Protective conductor connection ② 4x mounting space for 22.5 mm elements with slide-in labels ③ Power supply interface X10 ④ Switch S2 ⑤ Ethernet interfaces X20 port 1/ port 2 ⑥ Handwheel connections X60/ X61 ⑦... -
Page 19: Configuration
Operator control and display elements 4.3 Configuration Configuration Input image Slot 1 Base Slot 2 Keypad 1 (operating mode block) Slot 3 Keypad 2 (customer keys) Slot 4 Keypad 3 (axis block) Slot 5 Powerride 1 (feed) Slot 6 Powerride 2 (spindle) Slot 7 Handwheel 1 Slot 8... - Page 20 Operator control and display elements 4.3 Configuration ONE MCP Part 2: MCP 2200 Equipment Manual, 11/2022, A5E50324703B AC...
-
Page 21: Technical Data
Technical data MCP 2200 Safety Safety class according to EN 50178 III; PELV Degree of protection according to EN Front: IP65 Keyswitch: IP54 Rear: IP00 60529 Approvals CE / UL / EAC Flame resistance UL 94 V-1 UL identifier MCPS2001-529265E-1132091AA0 Electrical data Overvoltage category Secondary circuit supplied from primary circuits up to Cat. - Page 22 Technical data MCP 2200 Temperature change Max. 30 K/h Relative humidity 5 ... 90% (without condensation) Permissible change in the relative humidity Max. 6%/h Pollution degree 2 (only use indoors) Mechanical environmental conditions Classification of the mechanical environ‐ Class 3M2 according to EN 60721-3-3 ment Vibration load during operation Frequency range: 10 –...
- Page 23 Technical data Note Damage to components by coolants and lubricants The SINUMERIK operator components have been designed for industrial use, particularly on machine tools and production machines. This also takes into account the use of commercially available coolants and lubricants. The use of aggressive compounds and additives can damage components and result in their failure.
- Page 24 Technical data ONE MCP Part 2: MCP 2200 Equipment Manual, 11/2022, A5E50324703B AC...
-
Page 25: Index
Index MCP 2200 Emergency stop button, 23 Technical data, 21 Current consumption, 21 Power consumption, 21 ONE MCP Part 2: MCP 2200 Equipment Manual, 11/2022, A5E50324703B AC... - Page 26 Index ONE MCP Part 2: MCP 2200 Equipment Manual, 11/2022, A5E50324703B AC...