Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Husqvarna 525RX Mark II
Summary of Contents for Husqvarna 525RX Mark II
- Page 1 525RX Mark II, 525RXT Mark II Operator's manual 2-26...
-
Page 2: Table Of Contents
Contents Introduction..............2 Troubleshooting............21 Safety................4 Transportation and storage...........22 Assembly................ 9 Technical data.............. 23 Operation..............12 Accessories..............24 Maintenance..............18 Declaration of Conformity..........25 Introduction Product description not use the product for other tasks than grass trimming, grass clearing and forestry clearing. Use a saw blade to This product is a brushcutter with a combustion engine. - Page 3 3. Bevel gear 4. Cutting attachment guard The product can cause objects to eject, 5. Shaft which can cause injury. 6. Handlebar 7. Throttle control Keep a minimum distance of 15 m/50 ft. to 8. Stop switch persons and animals during operation of 9.
-
Page 4: Safety
Euro V Emissions yyyywwxxxx The rating plate shows the serial number. yyyy is the production year and ww is WARNING: Tampering with the engine the production week. voids the EU type-approval of this product. Note: Other symbols/decals on the product refer to certification requirements for other commercial areas. - Page 5 • Refer to national or local laws. They can prevent • Remove all unwanted materials from the work area or decrease the operation of the product in some before you start. If the cutting attachment hits an conditions. object, the object can eject and cause injury or damage.
- Page 6 • If it is necessary, use approved protective gloves. 3. Make sure that the throttle trigger is locked at the idle position when the throttle trigger lockout is • Use a helmet if it is possible that objects fall on your released.
- Page 7 is fitted this can cause serious personal 2. Do a visual check for damage, for example cracks. injury. Refer to, Technical data on page 23 . 3. Release and attach the quick-release mechanism to make sure that it operates correctly. The cutting attachment guard prevents injuries from objects that eject in the direction of the operator.
- Page 8 Cutting equipment blade correctly sharpened. Obey the instructions in To sharpen grass cutters and grass blades on page Choose and maintain the cutting equipment to: 21 and use the recommended file gauge. • Obtain maximum cutting performance. • Increase life span of the cutting equipment. •...
-
Page 9: Assembly
• Grass blades and grass cutters are used to cut • Never start the product if you spill fuel on it. Wipe the rough grass. spillage of and allow remaining fuel to evaporate. • A grass blade can cause injury while it continues •... - Page 10 To assemble the handlebar 5. Remove the clip from the handlebar. Put the tube into the clip and attach it to the handlebar. 1. Loosen the 2 screws on the handlebar bracket. 6. Adjust the handlebar to put the product in a correct work position.
- Page 11 5. Turn the output shaft until one of the holes in the Note: Use the recommended blade guard. Refer to drive disc aligns with the related hole in the gear Accessories on page 24 . housing. 6. Put the locking pin (D) in the hole to lock the shaft. 1.
-
Page 12: Operation
• For best results and performance use Husqvarna two-stroke oil. • If Husqvarna two-stroke oil is not available, use a CAUTION: Do not mix fuel for more two-stroke oil of good quality for air-cooled engines. than 1 month at a time. - Page 13 To fill the fuel tank • Make sure that there are no cracks at the bottom of the grass blade teeth or by the center hole of the blade. Replace the blade if it is damaged. WARNING: Obey the procedure that follows for your safety.
- Page 14 ™ technology and can use Husqvarna Fleet Services connect to mobile devices. This enables more functions. Husqvarna Connect Husqvarna Connect is a free app for your mobile device. The Husqvarna Connect app gives extended functions for your Husqvarna product. •...
- Page 15 Do not let go of ™ For more information about Husqvarna Fleet Services the starter rope handle when the starter refer to www.husqvarna.com. rope is fully extended. This can cause To prepare a cold engine for start damage to the product.
- Page 16 7. Reset the choke when the engine starts or after you • Move in a regular pattern across the work area. pull the starter rope 5 times. 8. If it is necessary, pull the starter rope again and again until the engine starts. 9.
- Page 17 blade thrust. The risk increases with the thickness of the • Hold the trimmer so that the trimmer head is just branch that is cut. above the ground. • Tilt the trimmer head at a slight angle. • Let the end of the trimmer line strike the ground around objects.
-
Page 18: Maintenance
4. Use full throttle when you move the product from 1. Hold the trimmer head and its trimmer line parallel to side to side to cut grass. the ground and above the ground. 2. Apply full throttle. 3. Move the trimmer head from side to side and sweep the grass. - Page 19 To adjust the idle speed 3. The idle speed is correct when the engine operates smoothly in all positions. The idle speed must be Your Husqvarna product is made to specifications that below the speed when the cutting attachment starts decrease harmful emissions.
- Page 20 3. Remove the screw holding the spark arrestor mesh. 4. Clean the spark arrestor mesh if it is blocked or replace it if it is damaged. CAUTION: The spark arrestor mesh To examine the spark plug must be replaced if it is damaged. Do not use a product if the spark arrestor mesh on the muffler is missing or defective.
-
Page 21: Troubleshooting
3/4 full with grease. Use Maintenance schedule on page 18 . intervals. Refer to Husqvarna special grease. 1. Move the choke lever up to close the choke valve. The grease in the bevel gear does not need to be changed unless repairs are carried out. -
Page 22: Transportation And Storage
Starting failure Check Possible cause Solution Starter pawls Binding pawls Adjust or replace the pawls. Clean around the pawls. Speak to an approved servicing dealer. Fuel tank Incorrect fuel Drain it and use correct fuel. type. Carburetor Adjustment of Adjust the idle speed with the T screw. the idle speed. -
Page 23: Technical Data
Technical data Technical data 525RX Mark II 525RXT Mark II Engine Cylinder displacement, cm 25.4 25.4 Idle speed, rpm 3000 3000 Speed of output shaft, rpm 6500/7500 6500/7500 Catalytic converter muffler Maximum engine power acc. to ISO 8893, kW/hp @ rpm 1.0/1.34 @ 8500... -
Page 24: Accessories
Accessories Accessories Approved accessories Accessory type Cutting attachment guard, art. no. Grass blade/grass cutter Grass 255-4 1" (Ø 255 4 teeth) 588 11 79-01 Grass blade 255-3 (Ø 255 3 teeth) 588 11 79-01 Plastic blades Tricut Ø 300 mm (Separate blades 588 11 79-01 have part number 531 07 77-15) Trimmer head... -
Page 25: Declaration Of Conformity
Declaration of Conformity EU Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Brush cutters Brand Husqvarna Type / Model 525RX Mark II, 525RXT Mark II Identification Serial numbers dating from 2023 and onwards... - Page 26 UK Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Brush cutters Brand Husqvarna Type / Model 525RX Mark II, 525RXT Mark II Identification Serial numbers dating from 2023 and onwards...
- Page 27 1818 - 006 - 20.12.2022...
- Page 28 Original instructions 1141712-26 2022-12-22...