Table of Contents
Advertisement
Device
To program
Simon XT talking
Press the Lights off button on the touchpad six times in
touchpad
rapid succession. On the sixth press, the touchpad
makes a longer beep.
Press the lock and unlock buttons at the same time.
Key fob
To learn (program) a sensor:
1.
From the Programming screen, enter the access code from
the codes listed in Table 5 on page 7. The display shows each
entered access code digit as a dot.
2.
Press OK. You are now in the programming screen.
3.
Press Sensors.
4.
Press Learn Sensor.
5.
Trip the sensor (see Table 6 on page 7). The Edit Sensor screen
will appear. If no further action is required (change sensor
name, number, or group) proceed to step 8. To exit, press
Close repeatedly.
6.
To change the sensor name, number, or sensor group press
the appropriate Edit icon and modify the value. To change
the sensor text, press the appropriate Edit icon, then choose
the item you would like to change.
7.
Press Save to keep the new sensor, or Cancel to abort
learning this sensor into the system (both of these choices will
return you to step 5).
8.
To exit, press Close repeatedly.
Sensor Naming
Please use the following guide when naming sensors:
•
Sensor names must have the word "window" or "door" from
the text library to interact with the touch screen Door and
Windows icons on the Main screen.
•
On the Edit Sensor name screen in programming, default the
screen to list and not keypad. This gives the user the list of
possible sensor names.
•
The Motion icon is controlled by sensors that are
programmed into the following groups: 15, 17, 18, 20, 28, or
32.
•
The Property icon is controlled by the following sensors:
•
All sensors learned into Group 43.
•
Sensors that are not named "window" or "door".
•
Sensors not learned into the Motion groups.
•
Sensors that are named keyfob, keychain or touchpad.
Sensor Testing
Test the sensors after all programming is completed and
whenever a sensor-related problem occurs.
8
Note:
While the sensor test is a valuable installation and service
tool, it only tests sensor operation for the current conditions. You
should perform a sensor test after any change in environment,
equipment, or programming.
Notify the central station you will be performing a test prior to
starting the test.
To test the sensors:
1.
Place all sensors in their secured (non alarm) state.
2.
Access the System Test screen through the Programming
Screen, and then press OK.
3.
Enter the dealer or installer code and press OK.
4.
Press Sensor Test.
5.
All learned in sensors will be displayed on this screen. Press
the arrows to scroll through the pages.
Test your sensors by tripping them one at a time. The panel
will display the number of transmissions received from
sensors you trip. See Table 7 below for specific instructions on
how to trip each sensor type.
The panel sounds beeps, and the display identifies the tripped
sensor and the number of RF packets received. Each beep
represents one RF packet. Count the number of beeps and
refer to Table 7 below for minimum requirements. The panel
displays Sn #, Name, and Rounds Detected (Packets). Scroll
through to make sure all sensor have been tested.
Table 7: Sensor tripping instructions
Sensor
Instructions
Hardwire contact Open the hardwire contact.
Door/window
Open the secured door or
window.
Carbon
Press and hold the Test/Hush
monoxide alarm
button (approximately 5 seconds)
until the unit beeps two times,
and then release the button.
Glassbreak
Test with an appropriate glass
break sensor tester.
Motion sensor
Avoid the motion sensor field of
view for 5 minutes, and then
enter its view.
Smoke
Press and hold the test button
until the system sounds
transmission beeps.
Key fob
Press and hold the Lock and
Unlock buttons simultaneously
for 3 seconds.
Simon XT talking
Press and hold the two
touchpad
Emergency buttons
simultaneously for 3 seconds.
Minimum
packets required
1
6 of 8
6 of 8
6 of 8
6 of 8
6 of 8
6 of 8
6 of 8
Simon XTi Installation Guide
Advertisement
Table of Contents
