D+H RZN 43-E Series Instructions For Use Manual

Smoke vent control panel
Hide thumbs Also See for RZN 43-E Series:

Advertisement

Instruction for use
A specialist company authorised by the manufacturer should carry out connection, installation and annual
Green control diodes in the buttons must be alight all the time, otherwise see "Trouble shooting".
Repair power failure immediately. Emergency power supply available for 72 hours.
housing
cable ducts
transformer
cable duct
Fig.: RZN 43xx-E6
Introduction
D+H service and sales partners
Safety in the building not only comes from the product. Above all, safety
results from competence. All D+H service and sales partners are certified
and regularly trained specialist SHEV businesses. Working closely with
D+H Mechatronic AG as the manufacturer, they develop comprehensive
system solutions for SHEVs and natural building ventilation. With integral
customer support and continuous quality assurance in all phases of the
project: from sales advice, planning and project management through to
installation, commissioning, repair and service. The highest national and
international quality standards are therefore reliably fulfilled.
Installation and operation
The comprehensive network of D+H service and sales partners is at your
disposal to professionally install your system and commission it. Our partner
system guarantees that D+H products are installed exclusively by trained
and experienced fitters, in compliance with the technical guidelines and
specifications. Personal handover and training for users is included.
99.821.70 3.5/01/12
Smoke Vent Control Panel RZN 43xx-E
Safety system protects human life and material assets!
rail
service.
motherboard with rectifier card
and power supply plug-in unit
keys
Maintenance and repair
Every building operator is responsible for ensuring that its safety equipment
works reliably. Regular and professional maintenance ensures that your
system is always operational. As specialist SHEV businesses, the D+H
service and sales partners are best qualified to carry out maintenance. By
taking out a maintenance contract, operators can prove at all times that they
have fulfilled their obligations.
Quality with guarantee
For all D+H SHEV systems, which have been installed by a D+H service and
sales partner and are regularly serviced, you will receive extended warranty
services. Ask your local D+H service and sales partner about this.
Always nearby
With the network of our own subsidiaries and exclusive partners, we are
represented nearly all over the world.
Are you looking for your local D+H partner?
Simply visit our website:
www.dh-partner.com
Installation
i n s t r u c t i o n f o r u s e
Smoke vent control book

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RZN 43-E Series and is the answer not in the manual?

Questions and answers

Summary of Contents for D+H RZN 43-E Series

  • Page 1 The highest national and Quality with guarantee international quality standards are therefore reliably fulfilled. For all D+H SHEV systems, which have been installed by a D+H service and sales partner and are regularly serviced, you will receive extended warranty Installation and operation services.
  • Page 2: Table Of Contents

    Update logbook. Smoke detector / fuse The respective current D+H maintenance instructions should be followed. A D+H authorised company has been specially trained by D+H for carrying Ground fault out this maintenance competently and will be automatically provided with the latest maintenance instructions.
  • Page 3: Motherboard / General Plug-In

    Motherboard for extension of control panel optional functional extension by modules (ribbon cable required) slots E1 and E2 optional functional extension by modules earthing 8 9 10 11 8 9 10 11 8 9 10 11 8 9 10 11 8 9 10 11 8 9 10 11 1 2 3 4 5 6 7...
  • Page 4: Optional Functional Extension / Wiring Plan / 230V Connection

    Cable and terminal boxes have to be labeled. WFR 41 Weather-stepping-relay for connecting of several D+H smoke vent control panels on a wind/ rain detector rain sensor Slot LE...
  • Page 5: Supply Plug-In Card Ve 520 / Ve 530

    Supply plug-in card VE 520 / VE 530 Supply plug-in card VE 520 / VE 530 1 x per control panel VE 520 : Control panels up to 16 A VE 530 Control panels from 32 A F0,125A Functions: F3,15A Monitoring of - Grid F1,25A...
  • Page 6: Line Plug-In Card Le 513

    Line plug-in card LE 513 line plug-in card for connecting of Detector Cables (Line): maximum 14 fire detectors and 8 The detector cables are monitored for short smoke vent buttons each circuit and break. Functions: The opening device is automatically triggered line On/ Off and opens up in the case of a fault, if DIP-switch alarm/ fault...
  • Page 7 RZN 4316-E RZN 4332-E RZN 4364-E No more than 10A on one group plug-in card. *** Fire detectors Only D+H - approved detectors permissible. **** Thermal fire recognition element, optional, is required by some fire authorities. 7/16 RZN 43xx-E 99.821.70 3.5/01/12...
  • Page 8: Group Plug-In Card Ge 628 (-L) V2

    2581, based on the set alarm direction (see DIP-switch 6). Therefor, the drive must be safeguarded against blockage in accordance with VdS 2580 Part 4.7. . All D+H drives meet this precondition. Otherwise DIP-switch 8 must be switched on OFF.
  • Page 9 * Please note: No type designation is given for these cables because of a Branch and terminal line in same direction. large variety on the market. Please consult your D+H distributor about Number of drives varies in accordance with lengths of lines. 4 wires are these.
  • Page 10: Servo Plug-In Card Se 622

    43xx-E. The unit is to convert an analogue preset D+H drive with value from the BMS into a drive stroke between 0- option "-SGI" 100% in conjunction with D+H drive with option or ZA...-SG "-SGI". Opening width can be steplessly Input (BMS) : selectable 0 -10V controlled, depending on the BMS input value.
  • Page 11 Servo plug-in card SE 622 continuation Connection SE 622 terminal module EM 47 K branch box by customer 0 - 10 V 0 - 10 V 0 - 20 mA 4 - 20 mA drive with -SGI or ZA-SG Mot.a Mot.b +SG(I) -SG(I)
  • Page 12: Weather Plug-In Card We 516

    Weather plug-in card WE 516 Encoding WE 516 You can select an infinitely variable wind-force setting between 2 and 8 on - weather plug-in card for - wind-/ rain transmitter the Beaufort scale using the regulator on the plug-in unit. As soon as the - central vent button wind force reaches the set value (time lag of a few seconds), the signal is...
  • Page 13: Window-Lock Plug-In Cardae 525-Aandae 526-Dg

    = alarm branch 10k * S1-2 -no function- first or ABF 12 penultimate YR 0,8 according to D+H table 10k * YR 0,8 for layout of cables * fire detector Only D+H approved AE 525-A detector permissible RZN 43xx-E...
  • Page 14: Trouble Shooting

    Trouble shooting Please check following points, if the smoke vent system fails to function satisfactorily or the green control LED in the button fails to lighten. Diagnosis must be carried out in following order: 1st supply plug-in card VE, 2nd line plug-in card LE, 3rd group plug-in card GE, 4th window lock plug-in card AE, 5th smoke detector and external control.
  • Page 15: Examination

    - Check fully charged accumulators that have not yet been used for correct In the case of excessive dirt accumulation and load, clean and re-grease open-circuit and on-load voltage using D+H accumulator tester, in outer mechanically moved parts. accordance with the testing table: Attention : Use only colourless fat-free Lusin A spray.
  • Page 16 D+H Mechatronic AG Georg-Sasse-Str. 28-32 22949 Ammersbek , Germany Tel. : +49 40-605 65 : +49 40-605 65 254 E-Mail: info@dh-partner.com www.dh-partner.com © 2010 D+H Mechatronic AG, Ammersbek Technische Änderungen vorbehalten. / Rights to technical modifications reserved. 99.821.70 3.5/01/12...

This manual is also suitable for:

Rzn 4308-eRzn 4316-eRzn 4332-eRzn 4364-e

Table of Contents