Numatic NX300 Original Instructions Manual
Scrubber dryer
Hide thumbs
Also See for NX300:
- Original instructions manual (116 pages) ,
- Instructions manual (36 pages) ,
- Safety and usage (12 pages)
Related Manuals for Numatic NX300
Summary of Contents for Numatic NX300
- Page 1 TTB 3045NX 36V S C R U B B E R D R Y E R Original Instructions CAUTION, Read instructions before using the machine numatic.com...
-
Page 2: Table Of Contents
Clean Water Level Indicator / Drainage Hose Trouble Shooting .........Page 15 Floor-Tool Retaining Knobs Battery Information...........Page 16-19 Floor Tool Deck Locking Mechanism Specifications .........Page 19 Deck Pressure Weights EU Declaration Document ......Page 17 Dual Charger + Batteries Warranty .........Page 23 Company Address .........Page 24 www.numatic.co.uk... -
Page 3: Machine Overview
TTB 3045NX 36V Machine Overview T 01460 68600... -
Page 4: Control Panel Overview
TTB 3045NX 36V Control Panel Overview Battery Charge Level Display Water Flow On / Off Button In the event of a breakdown contact Water Flow Indicator your Numatic dealer or the Vacuum Off/On Indicator Numatic Technical Vacuum Off/On Button help line +44 (0)1460 269268 Handle Position Lever Start Switch Triggers www.numatic.co.uk... -
Page 5: Machine Set Up Guide
Machine Set-up Guide ALWAYS ENSURE THAT THE MACHINE IS SWITCHED OFF BEFORE MAKING ANY ADJUSTMENTS Fitting the Brush / Pad / Turn on water 450mm Brush or 400mm Pad. Featuring the Nulock brush system. The brush is simply pushed and twisted to lock, making fitting and removal a simple process. Slide the brush / pad under the brush deck. Fit the brush / pad onto the Nulock drive chuck, twist to lock the brush / pad in place. -
Page 6: Fitting The Hose Guide
For best results use a non-foaming type of chemical recommended for use in auto scrubber dryers, dilute to the manufacturers specification. For further guidance on hazardous substances refer to health and safety instructions online. WHEN HANDLING AND MIXING CHEMICALS Always ensure that chemical manufacturer’s safety guidelines are followed. Only use chemicals recommended for use in auto scrubber-dryers. www.numatic.co.uk... -
Page 7: Handle Height Adjustment
Machine Set-up Guide Handle Height Adjustment Using the handle position lever, lower the handle to a comfortable working position. IMPORTANT Do not operate machine unless the Operator Manual has been read and fully understood. The machine is now ready to be moved to the cleaning site. -
Page 8: Lowering The Floor Tool
(Transit mode) simply lift the deck and the spring loaded locking pin will activate to hold the deck up. Setting the Cleaning Controls On / Off Trigger Trigger To check the battery level pull one of the Triggers or press button (A). Adjust water flow using the fluid control tap (B). www.numatic.co.uk... -
Page 9: System Error Indicators
To start the brush with the configured water and vacuum settings pull either trigger and press the Start switch (A). The running state of the vacuum (D) and water (C) can be adjusted whilst the brushes are running. To cancel vac overrun press any switch (vac/water/handle/start) System Error Indicators In the event of a fault the battery lights (F) will flash and the unit will stop operating. -
Page 10: Brush Pressure / Load Adjustment
Brush Pressure / Load Adjustment Using the Deck Pressure Weights. To obtain the best out of your TTB.3045.NX Numatic have supplied a ‘Deck Pressure Weight’ allowing the operator to add or remove pressure on the brush or pad for optimum performance on all floor types. Remove the Top (Waste Water) tank (1). Set in the lower tank are location pillars (2) to locate the Deck Pressure Weights (5). -
Page 11: Machine In Use
ALWAYS ENSURE THAT THE FLOOR IS PRE-SWEPT AND RELEVANT SAFETY SIGNS ARE DISPLAYED. Machine In Use To operate, set water flow rate tap, lower brush deck, lower the floor tool, press the vacuum / water switches, pull brush On/Off trigger. The waste water is then retrieved by the suction floor tool. Overlap each scrubbing path by 10cm to ensure an even clean. Do not operate the machine on inclines that exceed (2%), when full. On heavily soiled floors use a ‘double scrub’ technique. -
Page 12: Changing Floor Tool Blades
Replacement is a reversal of the removal process. Floor Tool Overview 1. Retaining pins x 4 2. Front blade (slotted) 3. Blade carrier 4. Rear blade 5. Floor tool main body Note: The blades are designed to be reversible, thus extending their useful working life. www.numatic.co.uk... -
Page 13: Rating Label / Personal Protective Equipment / Recycling
Protection Wet Floor Sign Note: A risk assessment should be conducted to determine which PPE should be worn. In the event of a breakdown contact your Numatic dealer or the Numatic Technical help line +44 (0)1460 269268 T 01460 68600... -
Page 14: Safety Precautions
Regularly examine the power cord for damage, such as cracking or ageing. If damage is found, replace the cord before further use. • Only replace the power cord with the correct Numatic approved replacement parts. • Ensure that the work area is clear of obstructions and / or people. -
Page 15: Schematic Diagram
Schematic Diagram Spare Parts BRUSHES CHARGER AND BATTERY 606203 450mm Polyscrub Brush 913686 LITHIUM ION BATTERY 606204 450mm Nyloscrub Brush 910820 DUAL LITHIUM BATTERY CHARGER 606306 450mm Longlife Brush 912365 CHARGER CABLE (UK) 900525 400mm NuLoc2 Drive Board Trouble Shooting PROBLEM CAUSE SOLUTION... -
Page 16: Battery Information
36V | 8400mAh | 300Wh | 10INR19/65-3 It is important that you observe the following information and warnings! Emergency Contact Informa� on Address: CBAK BATTERY HEADQUARTERS NUMATIC INTERNATIONAL LTD Shenzhen BAK ENERGY Co. LTD, Millfi eld Road, 2603A BAK Tech Bldg, Chard,... -
Page 17: Eu Declaration Document
• Do not use defective or deformed batteries. • Use only original NUMATIC chargers to charge the battery. • STORAGE: Good batteries should be stored in a protected area away from sources of direct heat and sunlight and should be kept dry. - Page 18 Use and store the battery with-in temperature range (as shown in Temperature Range Table). • Warning: The battery included in this product must only be charged by the Numatic Charger and docking system supplied with the product and in NO circumstances should an alternative non Numatic charger be used as there is risk severe damage and fi re could result.
-
Page 19: Specifications
To this end, batteries must be handed over for disposal to the collection systems established for this under national law. Disposal of batteries together with household waste is prohibited; batteries must be collected separately according to type. Return the battery free of charge to your NUMATIC servicing dealer for disposal or hand it over to an appropriate public • collection point. -
Page 20: Warranty
Warranty www.numatic.co.uk... - Page 21 Notes: T 01460 68600...
- Page 22 Notes: www.numatic.co.uk...
- Page 23 T 01460 68600...
- Page 24 Tel: 0861 686 284 www.numatic.co.za Numatic International Schweiz AG. Sihlbruggstrasse 3A, 6340 Baar. SCHWEIZ Tel: 0041 (0) 41 76 80 76 - 0 www.numatic.ch Numatic International ULDA. Rua da Boa Viagem, 177 4470.210 Maia. PORTUGAL Tel: +351 220 047 700 www.numatic.pt Numatic International SLU.