1. Manuals
  2. Brands
  3. TradePro Manuals
  4. Thermostat
  5. TP-P-511
  6. User manual

TradePro TP-P-511 User Manual

Programmable thermostats
Hide thumbs
1
2
3
4
5
6
7
8
9

Advertisement

Table of Contents

Programmable Thermostats
TP-P-511
TP-P-521
1 Specifications
2 Installation
3 Setting User Options
4 Setting Your Program Schedule
Warning
Attention
Read all instructions before proceeding.
This thermostat requires 24 Volt AC Power or two (2) properly installed
"AA" Alkaline batteries for proper operation. When connecting 24 Volt
AC Power the batteries may be installed as a backup.
installation and all components of the system shall conform to
Class II Circuits per NEC code.
For use only as described in this manual. Any other use will void warranty.
1 Specifications
This thermostat is compatible with:
• Single stage heat / cool conventional and heat pump systems
• Conventional systems up to 2 heat / 1 cool (TP-P-521)
• Single compressor heat pump systems with an auxiliary heat stage (TP-P-521)
• 250 – 750 millivolt heat only systems
Electrical and control specifications:
• Electrical Rating: 24 Volt AC
• 1 amp maximum load per terminal
• AC Power: 18 – 30 Volts AC
• DC Power: 3.0 Volt DC (2 "AA" Alkaline Batteries Included)
• Control Range: 45° – 90° F (7° – 32° C)
• Temperature Accuracy: +/- 1° F (+/- .5° C)
Terminations
• TP-P-511 – Rc, Rh, O, B, Y1, W1, G, C
• TP-P-521 – Rc, Rh, O, B, Y1, E/W1, G, W2, C
Single Stage Heat / Cool
Conventional and Heat Pump
Up to 2 Heat / 1 Cool
Conventional and Heat Pump
Model number is located on
back of thermostat
5 Operating Your Thermostat
6 Additional Operation Features
7 Thermostat Maintenance
Turn off power to the heating or cooling
equipment before installation.
For installation by experienced service
technicians only.
®
Manual
Thermostat
User
TPP-100-01

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TP-P-511 and is the answer not in the manual?

Questions and answers

Related Manuals for TradePro TP-P-511

Summary of Contents for TradePro TP-P-511

  • Page 1 • Control Range: 45° – 90° F (7° – 32° C) • Temperature Accuracy: +/- 1° F (+/- .5° C) Terminations • TP-P-511 – Rc, Rh, O, B, Y1, W1, G, C TPP-100-01 • TP-P-521 – Rc, Rh, O, B, Y1, E/W1, G, W2, C...

  • Page 2: Installation

    Avoid installation in locations where the thermostat can be affected by drafts, dead air spots, hot or cold air ducts, sunlight, appliances, concealed pipes, chimneys and outside walls. Install your new TRADEPRO thermostat in 5 basic steps: ® 1 Install the Sub-Base...
  • Page 3 Connect Your Wires Conventional Systems Typical Wiring Configurations NOTE: The “Installer Switch” option will be configured in the next step. Heat Only or Millivolt Set Installer Switch to CONV Rh Power Connection W Heat Relay (appears as W1/E on TP-P-521) Fan Relay [note 4] 24 Volt AC Transformer Common [note 1] 1 HEAT / 1 COOL Single or Dual Transformer...
  • Page 4 Heat Pump Systems Typical Wiring Configurations NOTE: The “Installer Switch” option will be configured in the next step. 1 HEAT / 1 COOL - No Auxiliary Heat Set Installer Switch to HP 24 Volt AC Power Connected to Rh with supplied Jumper Wire O or B Changeover Valve [note 2] Compressor Relay Fan Relay...

  • Page 5: Setting User Options

    Attach Thermostat to Sub-Base 1. Line up the thermostat body with the sub-base. 2. Carefully push the thermostat body against the sub-base until it snaps into place. 3. Insert quick reference card into slot on top of thermostat. 3 Setting User Options Advanced User Options User options allow you to customize some of your thermostat’s features.

  • Page 6: Setting Your Program Schedule

    4 Setting Your Program Schedule Setting the Time and Day 1. In normal operating mode, press the DAY/TIME button. The display will switch to the day/time setting mode and the hour will be flashing. 2. Press to adjust the hour. Press DAY/TIME.

  • Page 7: Operating Your Thermostat

    5. Press to adjust the temperature for the MORN event. Press PROG. 6. Repeat steps 3-5 for the DAY, EVE and NIGHT events. 7. Repeat steps 3-6 for the weekend (S, SU) program. 8. If needed, repeat steps 2-7 to program the opposite mode (HEAT or COOL). 9.

  • Page 8: Additional Operation Features

    Answers to any questions regarding our limited warranty may be obtained by writing our corporate offices. For warranty service, please visit your nearest TRADEPRO facility. ® Technical Assistance: 866-268-5599 (U.S.) • 630-844-1968 (Outside the U.S.) TPP-100-01 ©2018 TRADEPRO • All Rights Reserved • Made in China.

This manual is also suitable for:

Tp-p-521

Table of Contents

Save PDF