Download Print this page
Sealey SWF18WR.V2 Manual
Sealey SWF18WR.V2 Manual

Sealey SWF18WR.V2 Manual

18” 3-speed wall fan with remote control 230v

Advertisement

Quick Links

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Indoor use only
instructions
1. SAFETY
1.1.
ELECTRICAL SAFETY
WARNING! It is the user's responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey stockist.
if the used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable Appliance Test)
tested.
Electrical safety information, it is important that the following information is read and understood.
Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
9
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
9
Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the correct fuse - see
9
fuse rating in these instructions.
DO NOT pull or carry the appliance by the power cable.
8
DO NOT pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a firm grip on the plug.
8
DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or replaced immediately by a
8
qualified electrician.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch off the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
Class II products are wired with live (brown) and neutral (blue) only are marked with the Class II symbol;
A) Connect the BROWN live wire to the live terminal 'L'.
B) Connect the BLUE neutral wire to the neutral terminal 'N'.
C) After wiring, check that there are no bare wires and ensure that all wires have been correctly connected.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
DO NOT connect either wire to the earth terminal.
8
Sealey recommend that repairs are carried out by a qualified electrician.
1.2.
GENERAL SAFETY
Disconnect the fan from the mains power when not in use, and before servicing or performing any maintenance.
9
Use the fan in dry areas only. DO NOT use in wet or high condensation locations such as bathrooms, showers, or pools.
9
WARNING! If fan falls into water, immediately switch off and disconnect from the mains power supply. DO NOT touch the fan until
the mains power supply has been disconnected.
Always disconnect the fan from the power supply when moving it from one location to another.
9
Keep the fan clean and maintained in good condition (use an authorised service agent).
9
Use recommended parts only (unauthorised parts may be dangerous, and will invalidate your warranty).
9
DO NOT insert any objects through the fan guard.
8
DO NOT cover the fan.
8
DO NOT immerse the fan in water or any other liquid.
8
DO NOT allow children to operate the fan.
8
DO NOT place the fan where it may be knocked over easily, or where the lead may cause a person to trip.
8
DO NOT use the fan outdoors.
8
DO NOT use an extension cord unless it has been approved by an electrical authority.
8
When not in use store in a safe, dry, childproof location.
9
NOTE: This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities
or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by
a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
© Jack Sealey Limited
18" 3-SPEED WALL FAN WITH REMOTE CONTROL
230V
SWF18WR.V2
MODEL NO:
Original Language Version
Recommended fuse rating
3 Amp
SWF18WR.V2 Issue 1 18/02/21

Advertisement

loading

Summary of Contents for Sealey SWF18WR.V2

  • Page 1 SWF18WR.V2 MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
  • Page 2 Smooth running motor powers both fan blades and head oscillation. Timer function allows user to preset running time between 30 minutes - 4 hours. Sleep mode for gradual reduction of fan speed. Supplied with wall bracket for quick and easy installation. 3. SPECIFICATION fig.1 Model No: ............SWF18WR.V2 Fan Diameter: ............450mm (18”) Height: ............... 550mm Speeds: ................3 Oscillation: ...............
  • Page 3 BATTERY REMOVAL Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme. Jack Sealey Ltd Batteries Producer Registration Number (BPRN) is BPRN00705.