Download Print this page
Sealey AP6350 Instructions

Sealey AP6350 Instructions

Racking unit with 5 shelves (350kg capacity per level)

Advertisement

Quick Links

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1.
SAFETY INSTRUCTIONS
1.1 GENERAL SAFETY
WARNING! Ensure Health & Safety, and local authority regulations
!
are adhered to when assembling and using these shelves.
Locate shelves in a suitable area where they will not be an obstruction.
"
Keep the general area clean, uncluttered and ensure there is
"
adequate lighting.
WARNING! Erect shelves on a level and solid surface such as
!
concrete.
Keep children and unauthorised persons away from the storage area.
"
DO NOT use the shelves for any purpose other than that for
#
which they are designed.
DO NOT site the shelves out of doors.
#
DO NOT get the shelves wet or use in damp or wet locations or
#
areas where there is condensation.
DO NOT clean the shelf suports with any solvents which may
#
damage the coated surface.
Ensure that the shelves are properly assembled before loading
"
them with heavy items.
Maximum load for each shelf is 350kg.
!
Where possible the unit should be fixed to the wall with
"
suitable fixings
Place heavier items on the lower shelves.
"
Where possible heavier items should be evenly distributed across
"
the shelves.
2.
INTRODUCTION
Fully painted steel frame with five MDF shelves. 350kg capacity
per level giving a maximum capacity of 1750kg per rack. No nuts
and bolts means no tools required to assemble. Clips together in
minutes. Racking can be used as a single bay rack or split into
two separate shelf systems or workstations.
Height: 1805mm
Width: 910mm
3.
CONTENTS
Carefully unpack the product and check the contents against the
list below. Should any items be missing or damaged make
immediate contact with your Sealey dealer.
Part Description
LEG ANGLE SECTIONS (900x70x1.2mm)
LEG ANGLE JOINERS (28x61x1.2mm)
PLASTIC FLOOR PROTECTORS
SHELF SUPPORT, LONG (910x70x1.2mm)
SHELF SUPPORT, SHORT (415x70x1.2mm)
MDF SHELF (900 x 400 x 12mm)
FASTENER KIT (Nuts & bolts for joining side by side sections) 4
4.
ASSEMBLY
4.1 Assemble the frame using a soft faced hammer or mallet as
shown in Fig.1. If only a hard faced hammer is available hammer
onto a piece of wood to avoid damaging the paint surface. Always
hammer gently as close as possible to the uprights. Make sure
that the shelf support tabs are in line with the leg angle slots. If
the tabs and slots are not lining up do not use force as this may
damage the tabs. If the tabs are out of line bend them slightly to
line up with the slots.
Depth: 410mm
No Off
8
8
8
10
10
5
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
RACKING UNIT WITH 5 SHELVES
(350KG CAPACITY PER LEVEL)
4.2 See Fig.1. Decide on the position/height of the bottom shelf.
Make an end frame by fitting 1 short shelf support between 2 leg
angle sections. Make a second end frame ensuring that the shelf
support is at the same height as the first end frame. Join the two
end frames together using 2 long shelf supports fixed at the
same height as the short shelf supports.
4.3 See Fig.2. Decide on the height of the second shelf. Fit another 2
short shelf supports at the desired height then fit 2 long shelf
supports at the same height.
Fig.2
01284 757500
01284 703534
INSTRUCTIONS FOR:
AP6350
:
MODEL
Fig.1
www.sealey.co.uk
Web
sales@sealey.co.uk
email
AP6350 - 1 - 220207

Advertisement

loading

Summary of Contents for Sealey AP6350

  • Page 1 AP6350 MODEL Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
  • Page 2 4.7 See Fig.6. Move the frame into position in the chosen storage area. Place the 5 MDF shelves onto the shelf supports. Fig.6 Fig.8 AP6350 - 1 - 220207...