Table of Contents
Advertisement
8.4.1 TEMPERATURE ALARM SETTING
1. Press the ◀/▶/▲/▼ key to select
to confirm;
2. Press the ◀/▶ / ▲/▼ key to select
to confirm;
8.4.2 SET TEMPERATURE HI/LO ALERT LIMITS
1. Press ◀/▶ to select
2. Press ▲/▼ keys to adjust the Hi limit when(red)is selected;
3. Press ▲/▼ keys to adjust the Lo limit when(green)is selected;
The high temperature alarm default setting is 36 ℃,and the low temperature
Note:
alarm default setting is 8℃.When the temperature goes above or below the settings, the
temperature icon
the parent unit to stop beeping and flashing.
8.5 LULLABY SETTING
You can soothe the baby to sleep by playing a gentle lullaby from the Camera unit.
1. Press the MENU
◀/▶/▲/▼ keys until the lullaby iconis selected by red box;
2. Press the
3. Press the key enter into sub-menu;
4. Press the◀/▶/▲/▼key to select one of the 8 available lullabies, you can pick single
playback, loop (all 8 lullabies) playback
5. Presskey to confirm.
Note :
The lullaby default setting is OFF.
8.6 ALARM SETTING
1. Press the MENU
2. Press the ◀/▶/▲/▼ key until the alarm iconis selected by red box.
3. Press the ▲ / ▼ key enter into sub-menu, Press the ◀/▶/▲/▼key to selected the
alarm time you need;
4. Presskey to confirm;
5. Presskey to Exit.
Note 1:
The minimum unit is 0.5 hour. The maximum setting is 5 hours (7 levels).
Once the alarm is turned on, alarm icon will display on the screen;
Note 2:
Note 3:
The alarm default setting is OFF.
Note 4:
When the alarm is ringing, press any key on the parent unit to turn the alarm off.
Note 5:
If you don't turn off the alarm, the alarm will ring for 1 minute. After three minutes
the alarm will ring again for 1 minute. The alarm will ring for three times in total, after this
the alarm goes off.
8.7 VOX SETTING
This mode allows you to control the sound activation of your baby unit. If there is no sound
around the baby unit within 30 seconds, it will stop audio transmission and turn off the
or
for Hi/Lo limits settings;
will display on the screen. It will alert user by beeps. Press any key on
key and the menu will pop up.
key and the menu will pop up.
for turning on alarm function; Press
for turning off alarm function; Press
or stop
.
6
key
key
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the HB6550-2 and is the answer not in the manual?
Questions and answers
I can't find volume icon
My HB65 monitor will only remail no for about 1 second and I can't get the vox to shut off.
The HelloBaby HB6550-2 monitor remains on for about 1 second because the VOX (Voice Operated Exchange) mode is enabled. In VOX mode, the screen and audio transmission turn off if there is no sound detected around the baby unit for 30 seconds. The screen and audio transmission reactivate when sounds louder than the set sensitivity level are detected.
To turn off the VOX feature, follow these steps:
1. Press the MENU key to open the menu.
2. Use the ◀/▶/▲/▼ keys to select the VOX icon (highlighted with a red box).
3. Press the OK/ENTER key to enter the sub-menu.
4. Adjust the settings to disable VOX mode.
This answer is automatically generated
My signal keeps going out and showing a red X and the picture disappears, but then comes right back up. How do I fix this?
To fix the signal issue with the HelloBaby HB6550-2 that shows a red X and causes the picture to disappear, try the following steps:
1. Ensure the camera and monitor are both powered on.
2. Check if the power adapters are properly connected.
3. Move the monitor closer to the camera to improve the signal.
4. Ensure the camera and monitor are properly paired by following the pairing instructions.
5. Avoid placing the camera or monitor near metal objects or electronic devices that may cause interference.
6. Check if the battery power is low and recharge if necessary.
7. If the issue persists, try repowering the baby unit by unplugging and plugging it back in.
8. Press the RESET key on the back of the parent unit if the picture is frozen.
These steps should help restore the signal and display the picture correctly.
This answer is automatically generated
How do I set the time/date?
To set the time and date on the HelloBaby HB6550-2:
1. Press the MENU key to open the main menu.
2. Use the ◀ / ▶ / ▲ / ▼ keys to select the Setting icon.
3. Press the MENU key to open the Settings submenu.
4. Use the ◀ / ▶ / ▲ / ▼ keys to select the Time icon.
5. Press the ◀ / ▶ keys to select Month, Day, and Year, then use the ▲ / ▼ keys to set the desired values.
6. Use the ◀ / ▶ keys to select the 12H or 24H time format.
7. Use the ◀ / ▶ keys to select Hour and Minute, then use the ▲ / ▼ keys to set the desired values.
8. Press the Return key once to exit the submenu, and twice to exit the main menu.
This answer is automatically generated
Can I pair the hello baby monitor to my IPhone?