Table of Contents
Advertisement
Available languages
Available languages
EnGLIsh
nOTE: Battery packs should not be stored completely
depleted of charge. The battery pack will need to be recharged
before use.
Labels on Charger and Battery Pack
In addition to the pictographs used in this manual, the
labels on the charger and the battery pack may show the
L
following pictographs:
Read instruction manual before use.
p
Refer to Technical Data for charging time.
q
Do not probe with conductive objects.
r
Do not charge damaged battery packs.
s
Do not expose to water.
t
Have defective cords replaced immediately.
u
Charge only between 4 ˚C and 40 ˚C.
v
Only for indoor use.
x
Discard the battery pack with due care for
the environment.
y
Charge D
WALT battery packs only with designated
e
D
WALT chargers. Charging battery packs other than
e
the designated D
e
charger may make them burst or lead to other
dangerous situations.
z
Do not incinerate the battery pack.
Battery Type
The following tools operate on an 18‑volt battery pack:
DCF403, DCF414
These battery packs may be used: DCB181, DCB182, DCB183,
DCB183B, DCB183G, DCB184, DCB184B, DCB184G, DCB185,
DCB187, DCB189, DCBP034, DCBP034G, DCBP518, DCBP518G,
DCB546, DCB547, DCB547G, DCB548, DCB549. Refer to
Technical Data for more information.
Package Contents
The package contains:
1 Riveter
4 Nosepieces (DCF403)
3 Nosepieces (DCF414)
30
WALT batteries with a D
WALT
e
1 Set of spare jaws
1 Li‑Ion battery pack (C1, D1, E1, G1, H1, L1, M1, P1, Q1, S1, T1,
U1, X1, Y1, Z1 models)
2 Li‑Ion battery packs (C2, D2, E2, G2, H2, L2, M2, P2, Q2, S2,
T2, U2, X2, Y2, Z2 models)
3 Li‑Ion battery packs (C3, D3, E3, G3, H3, L3, M3, P3, Q3, S3,
T3, U3, X3, Y3, Z3 models)
1 Instruction manual
nOTE: Battery packs, chargers and kitboxes are not included
with N models. Battery packs and chargers are not included with
NT models. B models include Bluetooth® battery packs.
nOTE: The Bluetooth® word mark and logos are registered
trademarks owned by the Bluetooth®, SIG, Inc. and any use of
such marks by D
WALT is under license. Other trademarks and
e
trade names are those of their respective owners.
•
Check for damage to the tool, parts or accessories which may
have occurred during transport.
•
Take the time to thoroughly read and understand this manual
prior to operation.
Markings on Tool
The following pictograms are shown on the tool:
a
Read instruction manual before use.
g
Wear ear protection.
f
Wear eye protection.
n
Visible radiation. Do not stare into light.
Date Code Position (Fig. B)
The production date code
14
by a 2‑digit week and is extended by a 2‑digit factory code.
Description (Fig. A)
WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
Nosepieces
1
Screw cap
2
Nose housing
3
Nose housing nut
4
Mandrel collector
5
Spare nosepiece holder
6
Exhaust vent
7
Main handle
8
Trigger switch
9
LED worklight
10
Battery pack
11
Battery release button
12
Spare jaws
13
consists of a 4‑digit year followed
Advertisement
Table of Contents
