Table of Contents
Advertisement
Quick Links
FEBURARY 13 2018 PART NO:PX4000 Ver.01
DX400UL
DX400ULMOM8ECB, DX400ULACM4ECB.
Description
The DX400UL series of power supply/charger supplies a total of 4 amp nominal
c
o
t n
n i
u
o
u
s
s
u
p
p
y l
c
enclosure capable of accommodating one or two 12AH or 17.2AH lead acid rechargeable
batteries. The power supply models : DX400UL,DX400ULPD4ECB,DX400ULPD8ECB
have been evaluated for: CAN/ULC-S527,UL864,ULC-S318,UL603,UL294,
CAN/ULC-60839-11-1,CAN/ULC-S533. The above Power supplies are not intended to power
Fire Notification Appliances(Horns,Strobes & Bells). The power supply models:
DX400ULACM4ECB, DX400ULMOM8ECB have been evaluated for: UL294,
CAN/ULC-60839-11-1,CAN/ULC-S533.
General Specifications:
Input = 120 240VAC 50-60Hz, 1.8 Amp maximum, fuse at 4 Amp
Output 4 Amps continuous supply current PF 0.6 at nominal 12/24 VDC.
Built-in dedicated charger for sealed lead acid or gel cell type batteries.
Maximum battery charging current 1.5Amps (
Automatic switch over to stand-by battery upon AC failure or below 69.9VAC.
Battery presence detection within 10 seconds.
Temperature Compensated Battery Charger.(EN54-4 only,not UL evaluated)
Battery Charger Monitor.
Battery load test every 48hr.
Battery test result indication.
Battery Reversal protection.
12.
Low Battery indication at 11.40/22.80 Volts.
13.
Low Battery disconnect at 10/20.2 Volts.
14.
Low Battery, Battery disconnect, No Battery presence, battery
charger trouble reporting. (See FAULT TABLE)
15.
AC input indication by Green LED. (LED on when AC is present).
16.
AC Fault CMOS Relay contact for AC failure
17.
LEDs display on enclosure door (Green, Yellow, Blue).
18.
DC output indication by Blue LED, on board and enclosure.
Overload and short circuit protection on DC output.
19.
20.
Battery charging leads included.
21
Board Dimension: 195mm x 110mm
22.
Enclosure Dimension: 338 x 448 x 110mm(HP346 for 12Ah Battery)
Enclosure Dimension: 356 x 472 x 110mm(HP347 for 17.2Ah Battery)
23.
,
DX400ULPD4ECB, DX400ULPD8ECB,
Power Supply / Charger
r u
e r
t n
@
1
2
2 /
4
V
D
C
o
u
p t
t u
. s
t I
s i
n i
s
a t
e l l
n
t o
p
a
d
n i
a
a l
g r
e
s
h
e
t e
s
e t
t r
f o
h t
e
m
a
x
o
u
p t
t u
l e
c
r u
e r
n
r t
t a
n i
g
. )
.
1
Advertisement
Table of Contents
Related Manuals for Inaxsys DX400UL Series
Summary of Contents for Inaxsys DX400UL Series
- Page 1 DX400ULMOM8ECB, DX400ULACM4ECB. Power Supply / Charger Description The DX400UL series of power supply/charger supplies a total of 4 amp nominal e l l enclosure capable of accommodating one or two 12AH or 17.2AH lead acid rechargeable batteries. The power supply models : DX400UL,DX400ULPD4ECB,DX400ULPD8ECB have been evaluated for: CAN/ULC-S527,UL864,ULC-S318,UL603,UL294, CAN/ULC-60839-11-1,CAN/ULC-S533.
-
Page 2: Technical Specification
Technical Specification: 12/24 Vdc Regulated. Class E, unsupervised Output Voltage Output Amperage 4 Amp Ripple 50 mVp-p max Charging Current 1.5A Max, and not part of max output rating Battery Charging Voltage 13.8V/27.6V Nominal Operating Temperature 0deg.C to 49deg.C Performance Ratings UL 294 Performance Levels: Product Line Security Destructive Attack Endurance... -
Page 3: Relay Outputs
Relay Outputs: Output Output Type Description NORMALLY CLOSED TRIPS WITHIN 60 SEC. AFTER AC FAILS AC FAIL OPEN = FAULT CMOS RELAY RATING: 30VDC 60mA 16 OHMS BATTERY PROBLEM BATTERY NORMALLY CLOSED CMOS RELAY RATING: 30VDC 60mA 16 OHMS FAIL OPEN = FAULT Fault Condition &... - Page 4 Battery Operating Values Parameter Output Description Battery Disconnect voltage 10/20.2V When AC is off, the battery is disconnected when the battery voltage drops below this value. The battery is only reconnected when the AC is restored. Minimum battery voltage to 11.50V Red Led Flash 1 sec ON/OFF during pass battery test...
-
Page 5: Installation Instructions
Installation Instructions This power supply should be installed in compliance with National Electrical Code, NFPA70 as well NFPA72 National Fire Alarm Code, CSA C22.1, Safety Standard for Electrical Installations, Canadian Electrical Code, Part I, CAN/ULC-S524, and all applicable Local Codes. Installation to be performed by suitably qualified personnel. -
Page 6: Installation
PD4ECB, PD8ECB Description: The PD4ECB and the PD8ECB are distribution boards used for Fire Alarm, Bulglary, Access Control and Egress Doors installation. The PD4ECB and PD8ECB board have 4 and 8 outputs each rated max. 2.0Amp(max. total current 4 Amp), each with electronic overcurrent protection set at 2.5 Amp. - Page 7 2. Fire Alarm and Access Control interface connection Normally Open (NO), Normally Closed (NC) input or Polarity Reverse (Rev. Volt.) input are available to trigger the MOM8ECB operation. Connect the positive (+) and Negative (-) from the FACP/ACP to the REV. VOLT terminals observing the polarity,(polarity is referenced in alarm condition) or connect the NO or NC from the FACP/ACP output to the “Fire Trigger Terminals”.
- Page 8 ACM4ECB DESCRIPTION: The ACM4ECB is a distribution controller to be used with card Access Control, Egress Doors. It provides 12/24Vdc through 4 outputs rated 2.0A(max. 4A total) each with electronic over-current protection set at 2.5A. The 4 outputs will switch ON or OFF security devices such as Magnetic Locks, Door Strikes, etc.
- Page 9 Relay Output a) DC Fail: When one or more of the 4 outputs fail due to over current or short circuit condition, the DC fail Relay will open. Connect this output to monitoring device. (28Vdc, 300mA) b) Status Output: When the FACP or ACP input activates this will cause the dry contact Relay Form “C”...
- Page 10 DX400UL REGULATED POWER SUPPLY CHARGER UL/ULC LISTED AS FOLLOWS: U L294 ,CAN/ULC-60839-11-1,CAN/ULC-S533 FOR ACCESS CONTROL SYSTEM UL864,CAN/ULC-S527 FOR COMMERCIAL FIRE DATE OF MFG: UL603, ULC-S318 FOR BURGLARY ALARM SYSTEM NOTE: PLEASE REFER TO DX400UL INSTALLATION MANUAL, PART NO:PX4000 REV:01 PART NO:PX4001 REV:01 FIRE ALARM AND SECURITY EQUIPMENT COMMERCIAL FIRE I.T.E.
- Page 11 DX400ULPD4ECB REGULATED POWER SUPPLY CHARGER UL/ULC LISTED AS FOLLOWS: UL294 ,CAN/ULC-60839-11-1,CAN/ULC-S533 FOR ACCESS CONTROL SYSTEM UL864,CAN/ULC-S527 FOR COMMERCIAL FIRE DATE OF MFG: UL603, ULC-S318 FOR BURGLARY ALARM SYSTEM NOTE: PLEASE REFER TO DX400UL INSTALLATION MANUAL, PART NO:PX4000 REV:01 PART NO:PX4002 REV:01 FIRE ALARM AND SECURITY EQUIPMENT COMMERCIAL FIRE I.T.E.
- Page 12 DX400ULPD8ECB REGULATED POWER SUPPLY CHARGER UL /ULC LISTED AS FOLLOWS: UL29 4 ,CAN/ULC-60839-11-1,CAN/ULC-S533 FOR ACCESS CONTROL SYSTEM UL864,CAN/ULC-S527 FOR COMMERCIAL FIRE DATE OF MFG: UL603, ULC-S318 FOR BURGLARY ALARM SYSTEM NOTE: PLEASE REFER TO DX400UL INSTALLATION MANUAL, PART NO:PX4000 REV:01 PART NO:PX4003 REV:01 FIRE ALARM AND SECURITY EQUIPMENT COMMERCIAL FIRE...
- Page 13 DX400ULMOM8ECB This Product must be installed in compliance with National Electrical CodeNFPA70, REGULATED POWER SUPPLY CHARGER and all applicable codes. CSA C22.1, U L/ ULC LISTED AS FOLLOWS: Safety Standard for Electrical Installations, UL29 4 , C A N / ULC-60839-11-1,C A N / ULC-S533 Canadian Electrical Code.
- Page 14 TYPICAL APPLICATION WIRING DIAGRAM 2 OR MORE DX400ULMOM8ECB CONNECTED IN CASCADE PART NO: PX4005 REV:01 ACP or FACP TO REVERSED REV POL. POLARITY TERMINAL DX400 1 INPUT ONLY REV POL or FACP/ACP POWER INPUT CAN BE USED. TO FACP/ACP INPUT SUPPLY TERMINAL N/0 CONFIGURATION...
- Page 15 DX400ULACM4ECB This Product must be installed in compliance with National Electrical CodeNFPA70, REGULATED POWER SUPPLY CHARGER and all applicable codes. CSA C22.1, U L/ ULC LISTED AS FOLLOWS: Safety Standard for Electrical Installations, UL 29 4 , C A N / ULC60839-11-1,C A N / ULC-S533 Canadian Electrical Code.
- Page 16 TYPICAL APPLICATION WIRING DIAGRAM 2 OR MORE DX400ULACM4ECB CONNECTED IN CASCADE PART NO: PX4007 REV:01 TO REVERSED KEY PAD ACP or FACP ACCESS CONTROL POLARITY TERMINAL REV POL. PANEL RELAY OUTPUT 1 INPUT ONLY OUTPUT 1 AND 4 ARE DESABLE TO THE ACP/FACP FACP/ACP INPUT REV POL or FACP/ACP OUPUT 2 AND 3 ARE ENABLE TO ACP/FACP...
- Page 17 Tamper Switch Connection DICGU DICGU DICGU EOLR 1 TAMPER N/C EOLR 2 TAMPERS N/C DICGU DICGU EOLR DICGU EOLR 1 TAMPER N/O 2 TAMPERS N/O Fig. 3...
Need help?
Do you have a question about the DX400UL Series and is the answer not in the manual?
Questions and answers