Download Print this page
BEA UL294 Manual
BEA UL294 Manual

BEA UL294 Manual

Cylindrical universal electric strike

Advertisement

Quick Links

Visit website for available
languages of this document.
DESCRIPTION
5"
Only one bracket included.
The CYLINDRICAL UNIVERSAL ELECTRIC STRIKES are designed to accommodate either cylindrical or mortise locksets
up to 9/16" (15mm) throw latchbolt. When installed with a fail secure manner, the local authority shall be consulted
with regard to the use of possible panic hardware to allow emergency exit from the secured area.
UL294 & UL1034 REQUIREMENTS
‰ Indoor use only.
‰ Wiring methods shall be in accordance with NFPA70.
‰ 10STRIKECUV is intended to be used with UL-listed exit hardware.
‰ 10STRIKECUV shall not impair the intended operation of an emergency exit.
‰ 10STRIKECUV shall not impair the operation of panic hardware mounted on the door.
GENERAL SAFETY
‰ Shut off all power going to header before attempting any wiring procedures.
!
‰ Maintain a clean and safe environment when working in public areas.
‰ Constantly be aware of pedestrian traffic around the door area.
‰ Always stop pedestrian traffic through the doorway when performing tests that may result in unexpected reactions by the door.
CAUTION
‰ ESD (electrostatic discharge): Circuit boards are vulnerable to damage by electrostatic discharge. Before handling any board,
ensure you dissipate your body's ESD charge.
‰ Always check placement of all wiring before powering up to ensure that moving door parts will not catch any wires and cause
damage to equipment.
‰ Ensure compliance with all applicable safety standards (i.e. ANSI A156.10) upon completion of installation.
‰ DO NOT attempt any internal repair of the components. All repairs and/or component replacements must be performed by BEA,
Inc. Unauthorized disassembly or repair:
1. May jeopardize personal safety and may expose one to the risk of electrical shock.
2. May adversely affect the safe and reliable performance of the product resulting in a voided warranty.
©BEA
| Original Instructions
75.5011.01 CYLINDRICAL UNIVERSAL ELECTRIC STRIKE 20201110
CYLINDRICAL UNIVERSAL ELECTRIC STRIKE
5"
8"
Cylindrical electric strike for access doors
TECHNICAL SPECIFICATIONS
Operating voltage
12 or 24 VDC
Current draw
300mA (12 VDC)
150mA (24 VDC)
Operating temperature
32 – 120 °F (0 – 49 °C)
Humidity
0 – 85% non-condensing
Latch throw
" (15mm) max.
9
16
Keeper width
1
" (36mm)
6
17
Static strength
1000 lbs (454kg)
Dynamic strength
50 ft-lbs
Endurance
250,000 cycles (UL-tested)
1,000,000 cycles (factory-tested)
Material (strike body)
zinc alloy / stainless steel
Specifications are subject to change without prior notice.
All values measured in specific conditions.
Page 1 of 2

Advertisement

loading
Need help?

Need help?

Do you have a question about the UL294 and is the answer not in the manual?

Questions and answers

Summary of Contents for BEA UL294

  • Page 1 ‰ Ensure compliance with all applicable safety standards (i.e. ANSI A156.10) upon completion of installation. ‰ DO NOT attempt any internal repair of the components. All repairs and/or component replacements must be performed by BEA, Inc. Unauthorized disassembly or repair: 1.
  • Page 2 (not polarity sensitive) BEA, INC. INSTALLATION/SERVICE COMPLIANCE EXPECTATIONS BEA, Inc., the sensor manufacturer, cannot be held responsible for incorrect installations or incorrect adjustments of the sensor/device; therefore, BEA, Inc. does not guarantee any use of the sensor/device outside of its intended purpose.

This manual is also suitable for:

Ul1034