ENGLISH (Original instructions) SPECIFICATIONS Model: UC002G UC003G UC004G UC006G Overall length 266 mm (without guide bar and battery) Rated voltage D.C. 36 V - 40 V max Net weight 2.6 kg 3.8 - 4.5 kg 3.9 - 4.6 kg 4.0 - 4.7 kg 3.9 - 4.5 kg Standard guide bar length 250 mm...
Page 9
Saw chain, guide bar, and sprocket combination Saw chain type 90PX Number of drive links Guide bar Guide bar length 250 mm 300 mm 350 mm Cutting length 225 mm 281 mm 337 mm Pitch 3/8″ Gauge 1.1 mm Type Sprocket nose bar Sprocket Number of teeth...
Symbols Intended use The followings show the symbols which may be used The tool is intended for cutting branches and pruning for the equipment. Be sure that you understand their trees. It is also suitable for tree service. meaning before use. Noise Read instruction manual.
Wear safety glasses and hearing protection. NOTE: The declared vibration total value(s) has been Further protective equipment for head, hands, measured in accordance with a standard test method legs and feet is recommended. Adequate protec- and may be used for comparing one tool with another. tive clothing will reduce personal injury by flying NOTE: The declared vibration total value(s) may also debris or accidental contact with the saw chain.
in trees. Rappelling techniques are extremely • Follow the manufacturer’s sharpening and dangerous and require special training. The maintenance instructions for the saw chain. Decreasing the depth gauge height can lead operators must be trained to become familiar to increased kickback. with safety equipment usage and climbing techniques.
Page 13
Makita warranty for the Makita tool and Do not expose battery cartridge to water charger. or rain.
Tips for maintaining maximum Charge the battery cartridge with room tem- perature at 10 °C - 40 °C (50 °F - 104 °F). Let battery life a hot battery cartridge cool down before charging it. Charge the battery cartridge before completely dis- charged.
Let the machine and battery(ies) cool down. If no improvement can be found by restoring protection To prevent the switch trigger from being accidentally system, then contact your local Makita Service Center. pulled, a lock-off lever is provided. To start the tool, depress the lock-off lever and pull the switch trigger. NOTICE:...
The tool is equipped with the spike bumper as stan- cover to the chain saw body, and then close the cover dard. For replacement of the spike bumper, ask Makita so that the bolt and pin on the chain saw body meet Authorized Service Centers.
If you try to cut off thick branches from the top without a NOTICE: Use the saw chain oil exclusively for shallow undercut, the branch may splinter. Makita chain saws or equivalent oil available in ► Fig.26 the market. NOTICE: Never use oil including dust and parti- Carrying tool cles or volatile oil.
Chain blade 91PX : 4.0 mm To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should • Chain blade 80TXL : 4.0 mm be performed by Makita Authorized or Factory Service • Chain blade 25AP : 4.0 mm Centers, always using Makita replacement parts. —...
Remove the sprocket cover and saw chain from Before fitting a new saw chain, check the condition of the tool. the sprocket. ► Fig.36: 1. Sprocket 2. Areas to be worn out Remove the small dust or particles using a slotted screwdriver or the like. Always fit a new locking ring when replacing the sprocket. ► Fig.35: 1. Slotted screwdriver 2. Oil discharge hole ► Fig.37: 1.
TROUBLESHOOTING Before asking for repairs, conduct your own inspection first. If you find a problem that is not explained in the manual, do not attempt to dismantle the tool. Instead, ask Makita Authorized Service Centers, always using Makita replace- ment parts for repairs. Malfunction status Cause Action The chain saw does not start. Battery cartridge is not installed. Install a charged battery cartridge.