Safety Precautions General Guide Lines When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
Prevention of Electrostatic Discharge (ESD) to Electrostatically Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor "chip"...
About lead free solder (PbF) Note: Lead is listed as (Pb) in the periodic table of elements. In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder. The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu). That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.
Service Hints How to remove the backcover Lay the main unit face down. (see Fig.5) Fig.5 Remove the 4 fixing screws and the pedestal assembly. (see Fig.6) SCREWS (XYN4+F12FJK) Fig.6 Remove the 16 fixing screws. (see Fig.7) SCREWS SCREWS Fig.7...
Chassis Board Layout P-BOARD A-BOARD V-BOARD Board Name Function AV Terminal, HDMI, Digital Audio Out, TV tuner, SD A-Board Card, DVB-T/C Dem, sLD, AV Switch, EEPROM, Flash Memory, Speaker out, Hotel RS232, Hotel IR P-Board Power Supply, Main Input V-Board Remote Receiver, Cats, R/G LED Location of Lead Wiring To find the Part Number of required wire in Replacement Parts List click on the wire name in red box.
Technical Description Specification of KEY for CI Plus, DTCP-IP and One-to-One General information: 1. EEPROM (IC8950) for spare parts has the seed of KEY for each. 2. The final KEY data will be generated by sLD IC (IC8001) when SELF CHECK was done and are stored in both sLD IC (IC8001) and EEPROM (IC8950).
Self-check is used to automatically check the bus lines and hexadecimal code of the TV set. To enter Self-Check mode, keep pressing the down (-/v) button on the TV set and press the STATUS button on the remote control. To exit Self Check, switch off the TV set at the power button. Panasonic 2010LCD 42FHD Self Check Complete TH-42LRG20E C860 O.K.
Power LED blinking timing chart Subject Information of LED Flashing timing chart. Contents When abnormality has occurred the unit, the protection circuit operates and reset to the stand by mode. At this time, the defective block can be identified by number of blinking of the Power LED on the front panel of the unit. Blinking Blinking timing Contents...
Service Mode Function MPU controls the functions switching for each IICs through IIC bus in this chassis. The following setting and adjustment can be adjusted by remote control in Service Menu How to enter SERVICE While pressing (-/v) button on TV unit, press on the remote control for 3 times within 2 seconds.
SERVICE SERVICE Peaks SOFT 1.015 OPTION 1 Key Command ADJUST Peaks EEP 01.02.0027 OPTION 2 WB-ADJ LSI PACKAGE 0.030 OPTION 3 OPTION LSI DATA 1.00.05 OPTION 4 • SRV-TOOL STBY SOFT 1.00.00 Model ID Press the 3/4 button to change the adjustment values or function. STBY EEP 1.06.3602 03326100...
Service Tool Mode How to access Select [SRV-TOOL] in Service Mode. Press [OK] button on the remote control. SRV-TOOL Display of TD2Microcode version TD2Microcode:005a0910 Flash ROOM: AD – F1 Display of Flash ROM maker code POWER ON TIME/COUNT PTCT:00.00.00.00.00 Time 00051:30 On/Off 0000042 Display of SOS History Press [MUTE] button (3sec)
Hotel Mode 1. Purpose Restrict a function for hotels. 2. Access command to the Hotel mode setup menu. In order to display the Hotel mode setup menu, please enter the following command (within 2 second). [TV] : Vol.[Down] + [REMOTE] : AV (3 times) Then, the Hotel mode setup menu is displayed.
Data Copy by SD Card Purpose a) Board replacement (Copy the data when exchanging A-board): When exchanging A-board, the data in original A-board can be copied to SD card and then copy to new A-board. Following data can be copied. (Before exchanging) User setting data Copy to SD card...
Data Copy from TV set to SD Card Turn on the TV set. Insert SD card with a startup file (pwd file) to SD slot. On-screen Display will be appeared according to the startup file automatically. Input a following password for (a) or (b) by using remote control. (a) For Board replacement: 2770 (b) For Hotel: 4850 Data will be copied from TV set to SD card.
Data Copy from SD Card to TV set Turn on the TV set. Insert SD card with Data to SD slot. On-screen Display will be appeared according to the Data folder automatically. Input a following password for (a) or (b) by using remote control. (a) For Board replacement: 2771 (b) For Hotel: 4851 Data will be copied from SD card to TV set.
Option Bytes Description OPTION1 ATP Search Speed Slow (1) / Fast (0) TXT Ch Refresh On (1) / Off (0) ID-1 On (1) / Off (0) Macrovision Auto-Judge On (1) / Off (0) Surround enable low bit (*1) On (1) / Off (0) Surround enable low bit (*1) On (1) / Off (0) Pre Emphasis...
Adjustment Method Sub-Contrast/White Balance Adjustment Instrument Name Connect to Remarks Remote controller Correlation can be also taken by LCD WB meter (Minolta CS-1000A equivalent) CA-210 or equivalent Comunication jig Computer for external control Procedure Remarks Let the panel standfor more than 3 hours at more than 20 °C.
TBL0E0107 PEDESTAL ASSY FIX IC800 C0DBBYY00019 IC FOR POWER SUPPLY TBL0E0124 STAND MTG ASSY IC801 C0DABYY00017 REGULATOR TBMA352 PANASONIC BADGE IC802 C0DAZYY00028 IC FOR POWER SUPPLY TKP0E16001 CONNECTOR COVER IC803 C0DAEMZ00007 IC FOR POWER SUPPLY TKP0E39001 AC CORD BRACKET IC804...
Page 39
Cct Ref Parts Number Description Cct Ref Parts Number Description P4-INV TXJP4SQWB-2 P4-INV WIRE K1KA08B00270 8P CONNECTOR RELAYS RL800 K6B1AYY00050 RELAY RL801 K6B1AYY00050 RELAY DIFFERENCES FOR MODEL TH--42LRG20B EXPLODED VIEW A-42LRG20B A P.C.B. TXASX01QXB-3 AC CORD TBM0E1709 CI SLOT COVER SHEET TBM0E2334 MODEL LABEL MISCELLANEOUS COMPONENTS...
Schematic Diagrams IMPORTANT SAFETY NOTICE Components identified by mark have special characteristics important for safety. When replacing any of these components, use only manufacturers' specified parts. NOTE RESISTOR All resistors are carbon ¼W resistor, unless marked otherwise. Unit of resistance is OHM (Ω) (k=1,000, M=1,000,000) CAPACITORS All capacitors are ceramic 50V unless marked otherwise.