VooPoo ZIP mini - Vaper Manual

Introduction

Thanks for your purchase of a VOOPOO product. For the better use of all the functions of this product, please carefully read the operation notes and detailed functional instructions before your first use of this product. If you have any problems with using this product, please contact our local agent or visit our official website at www.voopoo.com.

Product Description

Product Appearance:

Parameters

Size: 80 x 48.5 x 24mm
Power Output: 5-120W
Capacity: Built-in Battery, 4400 mAh
Resistance Range: 0.05-5.0Ω(±5%)(TC) / 0.05-1.5Ω(±5%)(VW)
Program Upgradable: Yes

Security Protection

• Overtime protection
• Over temperature protection
• Output over-current protection
• Overcharge protection
• Low battery protection
• Atomizer short-circuit protection
• Support balance charge

Electric Parameter

Instructions

1. Basic Operation
   
   1. Press the power button five times in a quick sequenceto turn on or turn off the device
   2. Press the fire button three times constantly to switch modes: FIT mode → Power mode → Temperature
      Control mode
   3. Press "+" and "-" buttons simultaneously to enter function menu interface
   4. Press the fire button and "+" button simultaneously to lock or unlock the device
   5. Press the fire button and "-" button simultaneously to change screen orientation
2. Four Operating Modes:
   Introduction
   
   FIT Mode
   
   
   TC Mode
   
   
   Power Mode
   
   
   Custom Mode
   
   
3. Operations:
   1. FIT Mode:
      
      1. Default mode. There are there options available, and press "+" and "-"to select.
   2. Power Mode:
      
      1. Adjust the wattage from 5W to 120W. The mode could automatically recommend the output wattage according to the resistance value of a new atomizer - Press "+" and "-" at the same time to enter function menu interface:
         Power mode
         Custommode
         Series Number
         Software version
   3. TC Mode :
      1. Support five kinds of heating wire: SS, Ni, Ti, NC, TC; Factory Default Setting: SS, Ni, Ti; Connect a computer app to open NC, TC
         • TC adjustable range: 200-600℉ / 100-315℃
         • When the temperature is set at 100℃, keep pressing "-", it will turn to 600℉
         • When the temperature is set at 200℉, keep pressing "-", it will turn to 315℃
      2. To adjust wattage in TC mode, press the fire button four times, then the icon "W" will flash.
         The wattage can be adjusted from 5W to 80W.
         • Press "+" and "-" simultaneously to look up function menu:
           TC Mode
           Custom Mode
           Coil Cooling Value
           Coil Coefficient
           Coil cooling value range: 0.05Ω-1.5Ω.
           
   4. Custom Mode:
      1. Customization can be set under wattage mode and TC mode:
         • Press "+" and "-" simultaneously, then enter function menu. Select , and switch M1 to M5;
         • Press the power button three times to switch modes in a sequence: FIT mode → Wattage mode → TC customization (SS, Ni, Ti);
      2. Under custommode, there are two ways to adjust the value
         • Manually adjust the customized curve per second (press the power button four times to enter the interface. Press "+" and "-" to adjust the value. Press and hold the power button to exit

Watt curve—current watt value in the top right corner

TC curve—current temperature value in the top right corner

Connect to a computer app for custom settings

More instructions

1. Sleep Mode:
   The screen will be idle in 30s without any operations.
   After keeping for 30 minutes, the device will enter standby mode. Press the power button to activate.
   
2. Charging Mode:
   Upon charging with a 5V power supplier through USB cable, the device enters a state of charging with the running battery icon. When it is fully charged, the battery icon keepsunchanged.
   Note: It takes two hours to fully charge the device (5V/2A charger required)
   
3. Computer customization:
   Connect to the independently developed app to customize operations, such as prompt page, temperature coefficient, temperature curve, wattage curve, increase or decrease the type of coil, upgrade the device. Download address: http://www.voopoo.com.
   
4. Tips:
   TIME OUT
   
   
   CHECK COIL
   
   
   Low battery voltage
   
   
   Atomizer short circuit
   
   
   No atomizer
   
   
   HIGH TEMPERATURE
   
   
   High resistance value of the atomizer
   
   
5. Accommodation coefficient of the TC wire:
   

Note:

1. The higher the coefficient of the TC wire is, the higher the temperature is;
2. Since there are subtle differences among the material of TC wire from different companies, it is recommended to set the coil coefficient higher to get a better vaping experience when the power is not strong enough.
3. Please adjust the coefficient at a low rate to avoid firing cotton.

Attention :

1. Please keep device away from heat, fire and water.
2. Please do not drop, throw or immerse the device in water.
3. Please use the proper working mode according to your atomizer's material.
4. Please turn off or lock the device to avoid mis-firing when you take it on the go.
5. Keep the contents of this package out of reach of children and pregnant women.

Manufacture

Address: Block 1, Shapuyangyong Industry Park, Songgang, Bao'an District, Shenzhen, Guangdong, China.|
Email: support@voopootech.com
Website: www.voopoo.com
Instagram: voopootechofficial
Facebook: voopootech
Contact in EU:
Vaping Legal Ltd
Address: Armstrong House, First Avenue, Robin Hood
Airport, Doncaster. DN9 3GA. UK
Email: compliance@tpdcompliance.eu

Documents / Resources

References

• VOOPOO UK | Vape Pen & Machine | Spark Your Life

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download VooPoo ZIP mini - Vaper Manual