Summary of Contents for Metallkraft FSBM 1020-25E
- Page 1 Operating Instructions Folding Machine FSBM 1020-25 E, FSBM 1270-20 E FSBM 1520-15 E, FSBM 2020-12 E FSBM 1020-20 S2, FSBM 1270-20 HS2 FSBM 1020-20 HSG FSBM 1270-20 HS2...
-
Page 2: Table Of Contents
6 Installation and Operation........9 Fax: 0049 (0) 951 96555 - 55 6.1 Installation............9 6.2 Mounting of the back gauge (optional) ..... 10 E-Mail: info@metallkraft.de 7 Operation ............... 11 Internet: www.metallkraft.de 8 Care, maintenance and repair ......12 8.1 Care by cleaning..........12 8.2 Maintenance and repair ........ -
Page 3: Introduction
All information and notes in these operating instructions You have made a good choice by purchasing the Folding were summarised taking the applicable standards and Machine made by METALLKRAFT. rules, the state-of-the-art and our long-term knowledge Thoroughly read the operating instructions before and experiences into consideration. -
Page 4: Qualification Of Personnel
Safety Operator: ATTENTION! The operator is instructed by the operating company about the assigned tasks and possible risks in case of This combination of symbol and signal words indi- improper behaviour. Any tasks which need to be per- cates a possibly dangerous situation which may lead formed beyond the operation in the standard mode must to property and environmental damages if they are only be performed by the operator if it is indicated in... -
Page 5: General Safety Notes
Safety 2.4 General safety notes 2.6 Intended use The Folding Machine is exclusively intended for bending WARNING! of sheets of stainless steel and non-ferrous metals. The Danger in case of misuse! material to be operated must not exceed the max. thick- The folding machine may only be operated in techni- ness given in the technical data. -
Page 6: Technical Data
Technical Data Technical Data 3.1 Type plate Fig. 2: Type plate of FSBM 1020-20 HSG 3.2 Table Technical Data FSBM 1020-20 S2 FSBM 1270-20 HS2 FSBM 1020-20 HSG** Max. bending length 1020 mm 1270 mm 1020 mm Max. bending thickness S235* 2,0 mm 2,0 mm 2,0 mm... -
Page 7: Transport, Packaging, Storage
Transport, Packaging, Storage General risks during internal transport Transport, Packaging, Stor- WARNING: DANGER OF TIPPING 4.1 Delivery and Transport The device may be lifted unsecured by a maximum of 2cm. Delivery Employees must be outside the danger zone, the reach of loads. Check if there are any visible transportation damages af- Warn employees and, if necessary, advise employ- ees of the hazard. -
Page 8: Packaging
Description of the machine 4.2 Packaging NOTE! All used packaging materials and packaging aids of the - The machine must only be handled by experienced appliance are recyclable and generally need to be trans- personnel for loading, unloading and transport. ported to the material recycling. -
Page 9: Accessory For Option
- The ground must be level, stable and free of vibra- - FSBM 1020-20S2 tions - FSBM 1020-25E - The working area must be dry and well ventilated - FSBM 1270-20E - Machines causing dust and chips should not be op- - FSBM 1270-20HS2 erated in the vicinity of the folding machine. -
Page 10: Mounting Of The Back Gauge (Optional)
Installation and Operation 6.2 Mounting of the back gauge (optio- nal) Step 1: Screw the two guide rails (Pos. 2, Fig. 8) to the back of the machine (Fig. 11) using the four long screws (Pos. 6, Fig. 8). Use the four long screws (Pos. -
Page 11: Operation
Operation Step 7: Fasten the bended connector (Pos. 7, Fig. 9) WARNING! with the small screw (Pos. 5, Fig. 9) in the Risk of crushing! threaded hole in the junction of the angle bracket (Fig.10). In case of improper works on the folding machine there is a risk of injury on the upper limbs. -
Page 12: Care, Maintenance And Repair
Care, maintenance and repair Care, maintenance and repair 8.2 Maintenance and repair Lubricate all moving parts and bearings once per month. Tips and recommendations Maintenance and repair works must only be performed by specialists. If the machine does not work properly, In order that the machine is always in good operat- please contact a specialised dealer or our customer ser- ing status, it is necessary to regularly perform care... -
Page 13: Disposal, Recycling Of Used Devices
Disposal, recycling of used devices Disposal, recycling of used 10.1 Order of spare parts devices The spare parts may be purchased with the authorised dealer or directly with the manufacturer. Please find the ImFor environmental benefits it is necessary to ensure corresponding contact data in Chapter 1.2 Customer that all components of the machine are only disposed of service. -
Page 14: Spare Parts Drawings
Spare parts 10.2Spare parts drawings In case of service, the following drawings shall help to identify the necessary spare parts. Send a copy of parts drawing with the marked components to your authorised dealer when ordering spare parts. Spare parts drawing FSBM 1020-20 S2_1270-20 HS2 Fig. - Page 15 Spare parts Spare parts drawing FSBM 1020-20 HSG Fig. 13: Spare parts FSBM 1020-20 HSG FSBM Series | Version 1.06...
- Page 16 Spare parts Spare parts drawing FSBM 1020-25 E_1270-20 E_1520-15 E Fig. 14: Spare parts FSBM 1020-25 E_1270-20 E_1520-15 E FSBM Series | Version 1.06...
- Page 17 Spare parts Spare parts drawing FSBM 2020-12 E Fig. 15: Spare parts FSBM 2020-12 E FSBM Series | Version 1.06...
-
Page 18: Ec Declaration Of Conformity
According to Machinery Directive 2006/42/EC Annex II 1.A Manufacturer / distributor: Stürmer Maschinen GmbH Dr.-Robert-Pfleger-Straße 26 D-96103 Hallstadt hereby declares, that the following product ® Product Group: Metallkraft Metal working machines Machine type: Folding machine Designation of the machine *: FSBM 1020-25 E Item number *: 3772125... -
Page 19: Notes
Notes 12 Notes FSBM Series | Version 1.06... - Page 20 www.metallkraft.de...
Need help?
Do you have a question about the FSBM 1020-25E and is the answer not in the manual?
Questions and answers