DMR-ES35VEG / DMR-ES35VEC 1.1.1. LEAKAGE CURRENT COLD 1 SAFETY PRECAUTIONS CHECK 1.1. GENERAL GUIDELINES 1. Unplug the AC cord and connect a jumper between the two prongs on the plug. 1. Be careful during removing metal parts, sharp edges. 2. Measure the resistance value, with an ohmmeter, between 2.
DMR-ES35VEG / DMR-ES35VEC 2 WARNING 2.1. PREVENTION OF ELECTROSTATIC DISCHARGE (ESD) TO ELECTROSTATIC SENSITIVE (ES) DEVICES Some semiconductor (solid state) devices can be damaged Some solder removal devices not classified easily by static electricity. Such components commonly are as "anti-static (ESD protected)" can generate electrical called Electrostatic Sensitive (ES) Devices.
DMR-ES35VEG / DMR-ES35VEC 2.2. PRECAUTION OF LASER DIODE CAUTION: ACHTUNG: This product utilizes a laser diode with the unit turned “on”, Dieses Produkt enthält eine Laserdiode. invisible laser radiation is emitted from the pickup lens. Im eingeschalteten Zustand wird unsichtbare Laserstrahlung von der Wave length: 662 nm/795 nm Lasereinheit ausgestrahlt.
DMR-ES35VEG / DMR-ES35VEC 2.3. SERVICE CAUTION BASED ON LEGAL RESTRICTIONS General description about lead free Solder (PbF) · The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this equipment in considering the globally environmental conservation.
DMR-ES35VEG / DMR-ES35VEC 3 SERVICE NAVIGATION 3.1. SERVICE INFORMATION This service manual contains technical information which will allow service personnel to understand and service these models. Please place orders using the parts list and not the drawing reference numbers. 1. This service manual does not contain the following information, because of the impossibility of servicing at component level.
DMR-ES35VEG / DMR-ES35VEC 4 SPECIFICATION AC 220-240 V, 50/60 Hz RGB output level: 0.7 Vp-p (75 ) +/-10 % 26 W +/-1,3 W Output terminal: AV 1 (21 pin) Power Save mode: 2 W+/-0,4 W Number of terminals: 1 system 430 (W) ×...
DMR-ES35VEG / DMR-ES35VEC 5 NEW FEATURE 5.1. ABOUT DivX 5.1.1. GENERAL When playing this content · Number of remaining plays is reduced by one if DivX is a new video compressing format that is applied − you press [POWER] MPEG-4 technology to improve quality and the compressibility −...
Page 10
DMR-ES35VEG / DMR-ES35VEC CASE 1 WHEN DivX IS USED NEWLY Case 1...
Page 11
DMR-ES35VEG / DMR-ES35VEC CASE 2 WHEN EEPROM OR P.C.B. INCLUDING EEPROM WAS REPLACED FOR REPAIRING CASE 3 WHEN RECORDER WAS EXCHANGED TO ANOTHER RECORDER FOR REPAIRING Case 3 Case 2...
Page 12
DMR-ES35VEG / DMR-ES35VEC CASE 4 WHEN CUSTOMER OWN SECOND RECORDER Case 4...
Page 13
DMR-ES35VEG / DMR-ES35VEC CASE 5 WHEN OWNER OF RECORDER WAS CHANGED TO FILE KIND ANOTHER (There are two kinf of Activation files as follows too.) · Rental: There is a playback limitation · Purchase: Unrestricted Also there is next file as DRM files besides the above- mentioned.
Page 14
DMR-ES35VEG / DMR-ES35VEC · Conditions on counting number of times of play. 5.1.3. ABOUT DivX DRM 1. When a file was opened successfully. (At the time of Divx file includes file to which DRM(Digital Right Management) playback start) is applied and file not applied.
DMR-ES35VEG / DMR-ES35VEC 6 LOCATION OF CONTROLS AND COMPONENTS Remote Control DVD/VHS Stand-by/on switch Turn the television set on and off. DVD/VHS Press to switch the unit from on to stand-by mode Select the AV input on the television set.
DMR-ES35VEG / DMR-ES35VEC 7 OPERATING INTRUCTIONS 7.1. (DVD) TAKING OUT THE DISC FROM RAM-DRIVE UNIT WHEN THE DISC CANNOT BE EJECTED BY OPEN/CLOSE BUTTON 7.1.1. (DVD) FORCIBLE DISC EJECT 7.1.2. (DVD) WHEN THE FORCIBLE DISC EJECT CAN NOT BE DONE.
Page 17
DMR-ES35VEG / DMR-ES35VEC 7.2. (VHS) REMOVING OF 3. Stop unloading just before unloading will be completed. The CASSETTE TAPE tape becomes slack. When the cassette tape could not be removed after an 4. Rotate the S-Reel by a small minus screwdriver to remove electrical malfunction, there are 2 ways to remove a cassette the slack tape.
Page 18
DMR-ES35VEG / DMR-ES35VEC 7.2.3. (VHS) TAKE OUT CASSETTE TAPE 6. Attach Loading Motor and tighten the screw. MANUALLY AFTER REMOVING 7. Set the Position Switch to EJECT POSITION certainly and THE MECHANNISM attach the mechanism to chassis. 1. Disconnect the AC plug, and remove the Top Panel, Front Panel and the Mechanism by referring assembling and disassembling description.
DMR-ES35VEG / DMR-ES35VEC 8 SERVICE MODE 8.1. (DVD) SELF-DIAGNOSIS AND SPECIAL MODE SETTING 8.1.1. (DVD) SELF-DIAGNOSIS FUNCTIONS Self-Diagnosis Function provides information for errors to service personnel by “Self-Diagnosis Display” when any error has occurred. U**, H** and F** are stored in memory and held.
Page 20
DMR-ES35VEG / DMR-ES35VEC Error Code Diagnosis contents Description Monitor Display Automatic FL display NO READ Disc read error *A disc is flawed or dirty. “Cannot read. *A poor quality failed to start. Please check the *The track information could not be read.
DMR-ES35VEG / DMR-ES35VEC 8.1.2. SPECIAL MODES SETTING Item FL display Key operation Mode name Description Front Key TEST Mode *All the main unit´s parameters (include Press [VHS to DVD COPYING], tuner) are initialized. [REC] and [OPEN/CLOSE] keys simultaneously for five seconds when power is off.
Page 22
DMR-ES35VEG / DMR-ES35VEC Item FL display Key operation Mode name Description Front Key Aging Contents (Example): Demonstration Ejection of the disc is prohibited. *When lock the tray. When the power is on, press lock/unlock The lock setting is effective until unlocking [STOP] and [POWER] keys the tray and not released by “Main unit...
DMR-ES35VEG / DMR-ES35VEC 8.1.3. (DVD) SERVICE MODES Service mode setting: While the power is off, press [STOP], [VHS to DVD COPYING] and [OPEN/CLOSE] simultaneously for five seconds. Item FL display Key operation Mode name Description (Remote controller key) Release Items Item of Service Mode executing is cancelled.
Page 24
DMR-ES35VEG / DMR-ES35VEC Item FL display Key operation Mode name Description (Remote controller key) Magenta Picture Output Magenta picture is output with Component *Initial mode is “Interlace”. Press [1] [2] in service mode. Output from AV Decoder. *Magenta picture (Saturation rate: 100%) *It is enable to switch Interlace/Progressive by “I/P switch: [1] [4]”...
Page 25
DMR-ES35VEG / DMR-ES35VEC Item FL display Key operation Mode name Description (Remote controller key) RAM Drive Last Error RAM Drive error code display. 1. Error Number is displayed for 5 Press [4] [2] in service mode. *For details about the drive error code, refer seconds.
Page 26
DMR-ES35VEG / DMR-ES35VEC Item FL display Key operation Mode name Description (Remote controller key) Front connection Press all front keys and check the Press [5] [4] in service mode. inspection connection between Main P.C.B. and Front key Switches. (1) Each time a key is pressed, segment turned on increases one by one.
Page 27
DMR-ES35VEG / DMR-ES35VEC Item FL display Key operation Mode name Description (Remote controller key) AV2(V)/AV1(Y/C) I/O Set input to AV2 (V) and set output to AV1 Press [8] [2] in service mode. Setting (Y/C) for I/O checking AV2(RGB)/AV1(V) I/O Set input to AV2 (RGB) and set output to Press [8] [3] in service mode.
Page 28
DMR-ES35VEG / DMR-ES35VEC 8.2. (VHS) SELF-DIAGNOSIS AND SPECIAL MODE SETTING 8.2.1. (VHS) SPECIAL MODES SETTING Item FL display Key operation Mode name Description Front Key Tracking Center Tape Tracking is adj usted to center No display. During PLAYBACK, press [VHS CH FIX position.
Page 29
DMR-ES35VEG / DMR-ES35VEC Service Mode Contents Contents of Indication on minute Contents of Indication on second Remarks Number Manual mechanism Mechanism position (Real time) Ordering for the Motors Press the following key; operation PLAY key: Loading 0L: EJECT position 0*, 2*: CYL off,...
DMR-ES35VEG / DMR-ES35VEC 8.2.3.1.3. CLEAR FOR THE SELF-DIAGNOSIS HISTORY 1. Press STOP and EJECT buttons simultaneously over 5 seconds during turning on Service Information Display mode. 8.2.3.1.4. INDICATION OF THE SELF-DIAGNOSIS HISTORY The self-diagnosis histories can be indicated on the FIP with Service Mode number 3 to 5.
DMR-ES35VEG / DMR-ES35VEC 10 ASSEMBLING AND DISASSEMBLING 10.1. DISASSEMBLY FLOW CHART The following chart is the procedure for disassembling the casing and inside parts for internal inspection when carrying out the servicing. To assemble the unit, reverse the steps shown in the chart below.
DMR-ES35VEG / DMR-ES35VEC 10.4. TOP CASE 10.5. FRONT PANEL 1. Remove the 4 screws (A) and 3 screws (B). 1. Remove one screw (A). 2. Slide the Top Case for rear direction slightly, and open the 2. Unlock tab (A) and tab (B) simultaneously.
DMR-ES35VEG / DMR-ES35VEC Note: 10.7. REAR PANEL & FAN MOTOR When attaching Front Panel, in order to hook Cassette 1. Remove 10 Screws (A), Screw (B) Door Opener Lever to Cassette Door, push up cassette and Fan Connector. door in the direction of arrow and insert a front panel.
DMR-ES35VEG / DMR-ES35VEC 10.8.1. CAUTION FOR ATTACHING VCR 10.8. VCR MECHANISM UNIT MECHANISM UNIT 1. Disconnect 3 Connectors (P1531, P2501 and P4002). 1. Because Position SW should be set to "Eject Position", 2. Remove 3 black Screws (A), Screw (B), Screw (C) refer to fig.(A) and set the position switch so that the boss...
Page 35
DMR-ES35VEG / DMR-ES35VEC 10.9. MAIN P.C.B. 10.10. TUNER 1. Disconnect 3 Connectors. 1. Remove the solders. 2. Remove 3 Screws and remove Main P.C.B. . 2. Pull out the Tuner from Main P.C.B. .
Page 36
DMR-ES35VEG / DMR-ES35VEC 10.11. DVD-RAM DRIVE / DIGITAL P.C.B. MODULE CAUTION: The DVD-RAM Drive and the Digital P.C.B. have to be replaced together as one Module. If the Module is changed the DVD-RAM Drive has to be re-aligned because the aligment data for the DVD-RAM Drive is stored in the Digital P.C.B.
Page 37
DMR-ES35VEG / DMR-ES35VEC 10.12. DV IN P.C.B. 1. Remove 2 Screws. 2. Pull out the DV IN P.C.B. backwards. CAUTION: When replacing the Module, pay attention to inserting FFC, and be careful to do not touch surface of CSP ICs.
DMR-ES35VEG / DMR-ES35VEC Caution: 10.13. POWER & DIGITAL I/F P.C.B. The earth springs has to contact the Metalchassis. 1. Remove Rear Panel and disconnect 3 Connectors. 2. Remove the 6 Screws. 3. Remove DVD Angle (A) and DVD Angle (B).
DMR-ES35VEG / DMR-ES35VEC 11 MEASUREMENTS AND ADJUSTMENTS 11.1. SERVICE POSITIONS 11.1.1. CHECKING AND REPAIRING OF POWER & DIGITAL I/F P.C.B. CAUTION: Before repairing of Power & Digital I/F P.C.B. read and observe “CAUTION FOR DIVX” (NEW FEATURE) first. 1. Top Case ·...
DMR-ES35VEG / DMR-ES35VEC 11.1.2. CHECKING AND REPAIRING OF MAIN P.C.B. 1. Top Case · Remove 4 Screws (A) on side and 3 Screws (B) on rear side and remove the Top Case. 2. Front Panel · Remove on Screw (A) on center.
Page 41
DMR-ES35VEG / DMR-ES35VEC 11.1.3. CHECKING AND REPLACING OF DVD-RAM DRIVE / DIGITAL P.C.B. MODULE 1. Top Case · Remove 4 Screws (A) on side and 3 Screws (B) on rear side. · Remove Top Case. 2. Front Panel · Remove one Screws (A) on center.
DMR-ES35VEG / DMR-ES35VEC 11.2. CAUTION FOR REPLACING PARTS 11.2.1. NOTICE AFTER REPLACING DVD-RAM/DIGITAL P.C.B. MODULE TM AV1 is displayed after replacing DVD-RAM/Digital P.C.B. Module. Power-off and start-up again. 11.2.2. NOTICE FOR REPLACING PARTS OF VHS MECHANISM 11.2.2.1. REGARDING CHANGE OF PARTS OF VHS MECHANISM The following parts are not compatible with past R4 Mechanism.
Page 43
DMR-ES35VEG / DMR-ES35VEC 11.2.2.3. ITEMS THAT SHOULD BE DONE AFTER REPLACING PARTS * Note 1: Resetting object Condition of power Short Terminal IC6001 POWER ON TL6004 (Reset_L) and TL6002 (GND) IC9704 POWER ON IC9706-4 (Reset_L) and GND * Note 2: Please will always pass the customer “Warning for Customers Who Use the DivX Video-on-Demand content.”...
DMR-ES35VEG / DMR-ES35VEC * Note 3: PG Shifter Automatic Adjustment Procedure PROCEDURE F.I.P. DISPLAY Turn on the Service Mode 1. Set Drive Select to VHS and press the [STOP] and [EJECT] key simultaneously for more than 3 seconds. Activate the Service Mode 2 (Auto tracking will be turned off).
DMR-ES35VEG / DMR-ES35VEC LINEARITY ADJUSTMENT 1. After turning off the Auto tracking, playback the alignment Tape and press [VHS CH UP] and [VHS CH DOWN] keys simultaneously to adjust the tracking to FIX value. 2. Adjust the LINEARITY so that the envelope is flat when moving tracking to (+) and (-) directions.
Page 47
Perform auto recording and playback for one minute using No abnormality should be seen in the picture, sound or operation. the RAM disc. *Panasonic DVD-RAM disc should be used when recording and playback. If a problem is caused by a VCD, DVD-R, DVD-Video, No abnormality should be seen in the picture, sound or operation.
Page 48
DMR-ES35VEG / DMR-ES35VEC 12 MISCELLANEOUS 12.1. ABBREVIATIONS INITIAL/LOGO ABBREVIATIONS COMMON GROUNDING (EARTH) 12.1.1. DVD HA0~UP HOST ADDRESS HD0~UP HOST DATA HINT HOST INTERRUPT INITIAL/LOGO ABBREVIATIONS HRXW HOST READ/WRITE A0~UP ADDRESS IECOUT IEC958 FORMAT DATA OUTPUT ACLK AUDIO CLOCK IPFRAG INTERPOLATION FLAG...
Page 49
DMR-ES35VEG / DMR-ES35VEC INITIAL/LOGO ABBREVIATIONS INITIAL/LOGO ABBREVIATIONS SBI0, 1 SERIAL DATA INPUT VBLANK V BLANKING SBO0 SERIAL DATA OUTPUT COLLECTOR POWER SUPPLY SBT0, 1 SERIAL CLOCK VOLTAGE SERIAL DATA CLOCK VCDCONT VIDEO CD CONTROL (TRACKING SCKR AUDIO SERIAL CLOCK RECEIVER...
Page 50
DMR-ES35VEG / DMR-ES35VEC 12.1.2. VHS 3-1. ABBREVIATIONS 4.43 NTSC L 443NT [L] BILINGUAL BILINGUAL L A. COMP AUDIO COMPONENT SIGNAL BIL [L] BILINGUAL H BIL. [H] A. COMPO AUDIO COMPONENT SIGNAL BILINGUAL L AUDIO DUBBING PAUSE L BIL/M1 [L] A. D.P [L]...
Page 51
DMR-ES35VEG / DMR-ES35VEC CYL GND CYLINDER GND FULL. E. 12V FULL ERASE 12V DELAIED FM RECORDING H D.F.M. REC [H] GND [A] GND (ANALOG) DELAIED FM RECORDING L D. FM REC [L] GND [TU] GND (TUNER) D. GND DIGITAL GND GND/N.
Page 52
DMR-ES35VEG / DMR-ES35VEC POWER OFF H LINE IN [R] LINE INPUT (R) P-OFF [H] POWER OFF L LINE OUT [L] LINE OUTPUT (L) P-OFF [L] LINE OUT [R] LINE OUTPUT (R) P. FAIL POWER FAILURE DETECT LP H POWER OFF H LP [H] P.
Page 53
DMR-ES35VEG / DMR-ES35VEC RF OUT RF OUTPUT SYSCON 5V SYSTEM CONTROL 5V RF Y RF LUMINANCE SIGNAL SYSTEM SYSTEM SW TAKE-UP PHOTO TRANSISTOR RF. Y. IN RF LUMINANCE SIGNAL INPUT T-PHOTO TAKE-UP REEL PULSE RF. Y. OUT RF LUMINANCE SIGNAL OUTPUT T-RL.
DMR-ES35VEG / DMR-ES35VEC 13.2. SYSTEM CONTROL, SERVO & TIMER BLOCK DIAGRAM IC0201 (CAPSTAN MOTOR DRIVE) IC6001 (SYSTEM CONTROL/SERVO/TIMER) X SW +12V P0201 P2571 TL2502 CAPSTAN CAP TL MOTOR COILS P0201 P2571 MOTOR DIFFERENTIAL TORQUE CURRENT LIMIT DRIVE AMPLIFIRE CONTROL P0201...
DMR-ES35VEG / DMR-ES35VEC 13.3. AUDIO BLOCK DIAGRAM :REC SIGNAL :PB SIGNAL JK9301 REAR JACK Q9305 P9703 MIX_LOUT_DM LINE OUT Q9303 Q9304 FROM DIGITAL P.C.B. LINE OUT P9703 MIX_ROUT_DM Q9302 FROM XT_MUTE DIGITAL IC9704 INTERFACE IC3901 (SA1R) JK3901 21 PIN JACK...
DMR-ES35VEG / DMR-ES35VEC 13.4. VIDEO BLOCK DIAGRAM REC SIGNAL PB SIGNAL IC3901 MAIN P.C.B. ENC C IN P9703 P9103 P6003 C OUT DM ENC Y IN P9703 P9103 P6003 Y OUT DM FROM ENC R/R-Y IN P9703 P9103 P6003 RPROUT DM DIGITAL P.C.B.
Page 59
DMR-ES35VEG / DMR-ES35VEC REC SIGNAL PB SIGNAL IC3001 (AUDIO/VIDEO SIGNAL PROCESSOR) FIXED TO INT IN THES MODELS BY PIN53 2MHz IC3905 SVHS SQUELCH IC3901 -6dB -4dB FROM SVHS P9703 P9103 P6003 CLEAR DIGITAL SQUELCH V-AMP -10dB SYNC C_IN VIDEO FEED BACK...
DMR-ES35VEG / DMR-ES35VEC 15.5. FRONT JACK P.C.B. COMPONENT SIDE SOLDER SIDE EJECT EJECT S7804 S7804 R7802 R7804 K7801 DOWN DOWN S7803 S7805 S7802 S7806 S7803 S7806 S7802 S7805 K7802 POWER POWER R7801 S7801 S7801 W4818 W4812 W4813 W4807 C4801 PP4801...
Page 77
DMR-ES35VEG / DMR-ES35VEC 15.7. DV IN P.C.B. COMPONENT SIDE PP66802 PP66803 SOLDER SIDE P66803 DMR-ES35VEG DMR-ES35VEC DV IN PCB COMPONENT SIDE / SOLDER SIDE...
DMR-ES35VEG / DMR-ES35VEC 16 APPENDIX FOR SCHEMATIC DIAGRAM 16.1. VOLTAGE AND WAVEFORM CHART NOTE: · Indicated voltage values are the standard values for the unit measured by the DC electronic circuit tester (high-impedance) with the chassis taken as standard. Therefore, there may exist some errors in the voltage values, depending on the internal impedance of the DC circuit tester.
DMR-ES35VEG / DMR-ES35VEC 18 REPLACEMENT PARTS LIST NOTES: Ref. Part No. Part Name & Remarks Description *Important safety notice: VHD0690-1 SCREW Components identified by mark have special VHD1770 SCREW RHDC0023 SCREW characteristics important for safety. VHD1092-1 SCREW Furthermore, special parts which have purposes of...
DMR-ES35VEG / DMR-ES35VEC Ref. Part No. Part Name & Remarks Ref. Part No. Part Name & Remarks Description Description VMA0L25 TOP PLATE C1210 ECA1CHG471B ALU ELEC CAPACITOR VMD5468 SIDE PLATE(L) C1211 F1H1H1030007 CHIP CAPACITOR VMD5469 SIDE PLATE(R) C1212 F1H1C333A041 CHIP CAPACITOR...
Page 97
DMR-ES35VEG / DMR-ES35VEC Ref. Part No. Part Name & Remarks Ref. Part No. Part Name & Remarks Description Description C3034 ECEA1HKA010B ALU ELEC CAPACITOR C4023 F1H1E223A029 CHIP CAPACITOR C3036 ECEA1HKA4R7B ALU ELEC CAPACITOR C4024 F1H1H182A219 CHIP CAPACITOR C3037 ECEA1HKAR47B ALU ELEC CAPACITOR...
Page 98
DMR-ES35VEG / DMR-ES35VEC Ref. Part No. Part Name & Remarks Ref. Part No. Part Name & Remarks Description Description C5003 F1H1H1030006 CHIP CAPACITOR C7405 ECJ1VB1A105K CHIP CAPACITOR C5004 F1H1H1030006 CHIP CAPACITOR C7406 ECJ1VB1A105K CHIP CAPACITOR C5005 F1H1E104A030 CHIP CAPACITOR C7407 ECJ1VB1A105K...
Page 99
DMR-ES35VEG / DMR-ES35VEC Ref. Part No. Part Name & Remarks Ref. Part No. Part Name & Remarks Description Description C9720 F1H1H104A731 CHIP CAPACITOR D9107 B0AACK000004 SWITCHING DIODE C9721 ECJ1VB1A105K CHIP CAPACITOR DP7501 A2BD00000157 FL DISPLAY C9722 F1H1C104A042 CHIP CAPACITOR F1101 K5D202BK0005...
Page 100
DMR-ES35VEG / DMR-ES35VEC Ref. Part No. Part Name & Remarks Ref. Part No. Part Name & Remarks Description Description L1209 G0A470ZA0042 CHOKE COIL LB9711 J0JHC0000021 BEAD CORE L1210 G0A220GA0026 CHOKE COIL RADIAL P1101 K2AA2H000007 AC INLET L1211 G0A330ZA0042 CHOKE COIL...
Page 101
DMR-ES35VEG / DMR-ES35VEC Ref. Part No. Part Name & Remarks Ref. Part No. Part Name & Remarks Description Description QR4914 B1GBCFNN0009 TRANSISTOR R3010 D0GB153JA057 CHIP RESISTOR QR4915 B1GBCFJJ0007 TRANSISTOR R3013 D0GB101JA057 CHIP RESISTOR QR6402 B1GBCFJA0006 TRANSISTOR R3014 D0GB101JA057 CHIP RESISTOR...
Page 102
DMR-ES35VEG / DMR-ES35VEC Ref. Part No. Part Name & Remarks Ref. Part No. Part Name & Remarks Description Description R4525 D0GB333JA057 CHIP RESISTOR R6406 D0GB474JA057 CHIP RESISTOR R4526 D0GB102JA057 CHIP RESISTOR R6407 D0GB153JA057 CHIP RESISTOR R4527 D0GB102JA057 CHIP RESISTOR R6408 D0GB104JA057...
Page 103
DMR-ES35VEG / DMR-ES35VEC Ref. Part No. Part Name & Remarks Ref. Part No. Part Name & Remarks Description Description R9310 D0GB473JA057 CHIP RESISTOR R9784 D0GB101JA057 CHIP RESISTOR R9311 D0GB473JA057 CHIP RESISTOR R9785 D0GB101JA057 CHIP RESISTOR R9312 D0GB471JA057 CHIP RESISTOR R9786 D0GB101JA057...
Page 104
DMR-ES35VEG / DMR-ES35VEC Ref. Part No. Part Name & Remarks Ref. Part No. Part Name & Remarks Description Description ERJ6GEY0R00Z CHIP RESISTOR W532 D0YBR0000020 CHIP RESISTOR ERJ6GEY0R00Z CHIP RESISTOR ERJ6GEY0R00Z CHIP RESISTOR W216 D0YBR0000020 CHIP RESISTOR D0YBR0000020 CHIP RESISTOR ERJ6GEY0R00Z...
Page 105
DMR-ES35VEG / DMR-ES35VEC 18.5. SERVICE FIXTURE AND TOOLS Ref. Part No. Part Name & Description Remarks RFKZ03D01K Lead Free Solder (0.3 mm / (SPC) 100 g Reel) RFKZ06D01K Lead Free Solder (0.6 mm / (SPC) 100 g Reel) RFKZ010D01 Lead Free Solder (1.0 mm /...