1 gige port/1 pots port small form factor ont (4 pages)
Summary of Contents for ADTRAN NetVanta 644
Page 1
NetVanta 644 VoIP Gateway Hardware Installation Guide 1700144G1 NetVanta 644 61700144G1-34A June 2011...
Page 2
To the Holder of the Manual The contents of this manual are current as of the date of publication. ADTRAN reserves the right to change the contents without prior notice. In no event will ADTRAN be liable for any special, incidental, or consequential damages or for commercial losses even if ADTRAN has been advised thereof as a result of issue of this publication.
Page 5
Advance notification and the opportunity to maintain uninterrupted service are given. 4. If experiencing difficulty with this equipment, please contact ADTRAN for repair and warranty information. The telephone company may require this equipment to be disconnected from the network until the problem is corrected, or it is certain the equipment is not malfunctioning.
Page 6
Class A prescrites dans la norme sur le materiel brouilleur: “Appareils Numériques,” NMB-003 edictee par le ministre des Communications. Service and Warranty For information on the service and warranty of ADTRAN products, visit the Support section of the ADTRAN website at http://www.adtran.com.
INTRODUCTION This hardware installation guide describes the NetVanta 644 unit’s physical characteristics, lists their features and specifications, introduces basic functionality, and provides installation instructions. • Physical Description on page 14 • Product Specifications on page 17 • Unit Installation on page 18...
120 channels of VoIP to their customers. The NetVanta 644 can provide up to 120 channels of VoIP and includes four modular T1/E1 wide area network (WAN) interfaces, two 10/100/1000Base-T Ethernet ports, an integrated router, stateful inspection firewall, and transparent Session Initiation Protocol (SIP) proxy.
NetVanta 640 Series Hardware Installation Guide Physical Description Front Panel Design The NetVanta 644 front panel is shown below. T1/E1 REDUNDANCY STATUS CONSOLE STATUS NetVanta 640 ETH 1 ETH 2 Figure 1. NetVanta 644 Front Panel Layout Front Panel Features Status LEDs The status LEDs are located on the right side of the front panel.
(via a DB-9 female connector). See for the craft interface pinouts. Connection directly to an external modem requires a cross-over cable. Rear Panel Design The NetVanta 644 rear panel is shown below. CAUTION: DISCONNECT ALL POWER SOURCES PRIOR TO SERVICING UNIT BATT...
To prevent electrical shock, do not install equipment in a wet location or during a lightning storm. The NetVanta 644 is intended to be to be installed, maintained, and serviced by qualified service personnel only and should be installed in a restricted access location as described in UL/IEC 60950-1.
Unit Installation Mounting Options The NetVanta 644 can be installed in rackmount, wallmount, or tabletop configurations. The following sections provide step-by-step instructions for rack mounting and wall mounting. When installing and operating the NetVanta 644, a minimum of 1-inch clearance should be maintained on all sides of the unit.
Page 20
Decide on a location for the NetVanta, keeping in mind that the unit needs to be mounted at or below eye-level so that the LEDs are viewable. The NetVanta 644 can only be wall mounted with the front panel facing to the right or left (see the example in Figure 3 on page 21).
Supplying Power to the Unit The NetVanta 644 units come equipped with a 110 to 240 VAC, 50/60 Hz power supply for connecting to a properly grounded power receptacle. (A detachable power cable with a grounded, three-prong plug comes with the shipment.) To power this unit, connect the power cable to an appropriate AC power source.
Page 24
To order replacement batteries, reference the following part number: 1975044L1 (12 V replacement batteries). ADTRAN is an environmentally friendly company. Therefore, we encourage the proper recycling and handling of the batteries. Federal and state laws prohibit the improper disposal of all lead acid batteries.
Your NetVanta unit is now ready to be configured and connected to the network. For information on configuration for a specific application, refer to the configuration guides provided online on the ADTRAN’s Knowledge Base at http://kb.adtran.com. For details on the CLI, refer to the AOS Command Reference Guide (ADTRAN’s Knowledge Base article 2219).
Need help?
Do you have a question about the NetVanta 644 and is the answer not in the manual?
Questions and answers