Patton PUH680 - Heater Manual

Table of Contents

Contents

1 FEATURES - OPERATIONS
2 CLEANING/MAINTENANCE
3 AUTO SAFETY SHUT-OFF WITH INSTANT TIP-OVER PROTECTION
4 TROUBLESHOOTING
- 4.1 If your heater fails to operate
5 Documents / Resources
- 5.1 References
- 5.2 Download manual

FEATURES - OPERATIONS

TECHNICAL SPECIFICATIONS

Amps: 12.5
Wattage: 1500W (+5% -10%)
Working voltage: 120V AC/60Hz

ASSEMBLY INSTRUCTIONS

Carefully remove your heater and all parts from the box.
It is recommended to save carton for off-season storage.

This package includes

1 - Heater
1 - Carry Handle
2 - Screws

Handle Assembly

Place the heater in upright position.
Use the provided screws to attach the carry handle on top of the heater housing.
Use screw driver to tighten the screws firmly. Please ensure that screws are not overtightened.

NOTE: THIS UNIT IS FOR FLOOR USE ONLY.

OPERATING INSTRUCTIONS

Place heater on firm level surface.
Avoid overloading your circuit by not using other high wattage appliances in the same outlet. At 1500 Watts, this unit draws 12.5 Amps.

Mode Settings

To start heater operation, turn Thermostat control clockwise to the highest setting.
Switch the Selector to your desired heat settings:
1 - Low Heat
The heater will run continuously at 1350W.
2 - High Heat
The heater will run continuously at 1500W.
The Power Light will remain lit during operation.

Thermostat Control

Turn the Thermostat Control clockwise to the highest position to start heater. Allow heater to operate and warm up the room.
When the desired temperature/comfort level is reached, lower the temperature setting by turning the Thermostat Control counter-clockwise until the heater stops operating.
The thermostat will now automatically maintain the pre-set temperature level by turning the heater ON and OFF.

NOTE: It is normal for the heater to cycle ON and OFF as it maintains the preset temperature. To prevent the unit from cycling, raise the temperature setting.

Parts and Controls

Figure 2

Selector/Power Light
Thermostat Control
Protective Front Guards
Carry Handle

Figure 3
CONTROL PANEL CLOSE-UP

Selector/ Power Light
Thermostat Control

CLEANING/MAINTENANCE

Always unplug the heater before cleaning and allow the heater to cool down.

Clean the unit with a soft cloth moistened with a mild soap and water solution.
NEVER use abrasive or flammable solvents to clean the unit.
After cleaning, be sure to completely dry the unit with a cloth or towel.
Store heater in a cool, dry location.
It is recommended that you store the unit in its original carton.

AUTO SAFETY SHUT-OFF WITH INSTANT TIP-OVER PROTECTION

This heater is equipped with a Total Safety System with tip-over protection that will shut-off the heater in an overheat situation.

Tip-over Shut-off

When the unit is accidentally knocked over, it will shut off. To reset, simply place the heater in an upright position on a level surface.

Overheat Shut-off

When a potential overheat temperature is reached, the system will automatically shut the heater off. Make sure heater is clear of all obstructions. It can only resume operation when the user resets the unit.

RESET INSTRUCTIONS

If your heater shuts down:

Turn Control to OFF.
Unplug the unit and wait 30 minutes.
Plug in and operate normally.

TROUBLESHOOTING

If your heater fails to operate

The thermostat might be set too low. Turn the Thermostat Control clockwise until the heater restarts.
Make sure the Selector is in Low (1) or High (2) setting.
Make sure the electrical outlet or circuit breaker is working.
Check for obstructions. If you find an obstruction turn the heater OFF, and UNPLUG THE UNIT. Carefully remove the obstruction and follow the reset instructions.

Please DO NOT attempt to open or repair the heater.

If you have any questions regarding your product or would like to learn more about other Patton ® products, visit our website at www.pattonproducts.com.