Huawei PDU8000 Quick Installation Manual page 2

Tools / 安装工具
Phillips/Flat-head
Adjustable wrench Socket wrench
screwdriver
套筒扳手
活动扳手
十字 / 一字螺丝刀
Wire stripper COAX crimping tool
Hydraulic pliers Diagonal pliers
剥线钳 液压钳 压线钳
Measuring tape Protective gloves Insulated gloves
卷尺
防护手套 绝缘手套
Short-handle Phillips
Electroprobe Step ladder (2 m)
Electrician's knife
screwdriver (85 mm)
电笔
人字梯(2m) 电工刀
短柄十字螺丝刀(85mm)
Circuit breaker Layout / 空开示意图
NOTE / 说明
Cabinet dimensions (H x W x D): 2500 mm x 800 mm x 1200 mm
机柜尺寸（高×宽×深）：2500mm×800mm×1200mm
Input circuit breaker
输入空开
FS QFS FAN
Surge protective
1QF 2QF
device (SPD) and
SPD circuit breakers
防雷器及防雷空开
2
Installing a transformer PDC / 安装变压器配电柜
Checking Before Installation / 安装前检查
Open the packing case, and check that all components listed in the packing list are intact. Ensure that all components
are available before cleaning up the package materials. If components or fittings are damaged during transportation or
do not comply with the order contract, make records onsite and contact the local Huawei regional office or
Hammer drill
Claw hammer
representative office immediately.
冲击钻
羊角锤
打开包装箱，根据装箱清单检查设备的配件是否齐全、是否在运输过程中损坏。清除包装材料之前，要确保所有配件都
已找到。如设备和配件在运输中损坏或与订货合同不符，应及时现场记录，并与华为公司当地分公司或办事处代表联系。
Installing the Cabinet / 安装机柜
Level
Move the cabinet from the wood pallet to the ground.
斜口钳 水平尺
将机柜从木栈板移动至地面。
Plan the cabinet installation position based on the following figure.
参考下图规划机柜安装位置。
Unit: mm
单位：mm
Heat gun
热风枪
1200
Drill holes using a hammer drill and install expansion bolts.
用冲击钻钻孔并安装膨胀螺栓。
Align the cabinet with mounting holes.
将机柜对齐安装孔。
Insert bolts into the mounting holes and partially tighten the bolts.
将螺栓插入安装孔并预紧固。
Input circuit breaker
输入空开
Fan circuit
breakers
风扇空开
Output circuit
breakers
输出空开
Tighten the bolts in diagonal order.
按对角线顺序交叉紧固螺栓。
NOTE / 说明
The following table lists the tightening torque of different bolts.
各螺栓紧固扭矩说明如下表所示。
Bolts /
螺栓
NOTE / 说明
M8
The positions and number of circuit
breakers in the figure are for
M10
reference only. The actual product
M12
prevails.
空开位置和数量仅为示意，请以实
M16
物为准。
800
NOTE / 说明
If the cabinet is installed on a support, skip steps 2
and 3.
如果机柜安装在支架上，步骤2、3可省略。
1036
Recommended Torque
/ 推荐扭矩 (N· m)
13
27
47
120
3
Installing Input and Output Cables / 安装输入输出线缆
Input cables / 输入接线
The ground terminal is identified by a
sign.
接地端子通常以
S200
SH200
S200M S200P
Left view of the transformer PDC / 变压器配电柜左视图
Output cables / 输出接线
S200
S200M SH200
S200P
Left view of the transformer PDC / 变压器配电柜左视图 Right view of the transformer PDC / 变压器配电柜右视图
4
NOTE / 说明
标识。
NOTE / 说明
Cables are routed in and out from the top.
进出线方式为：上进上出线。
NOTE / 说明
The positions of cable holes in the figure
are for reference only. The actual
product prevails.
图中出线孔位置仅为示意，具体请以实物
为准。
S200
SH200
S200M
S200P