Wirquin Macdee JOLLYFLUSH Installation

INLET VALVE
JOLLYFILL TELESCOPIC
BOTTOM ENTRY INLET VALVE
A : PRE-INSTALLATION
1
Turn off water supply to cistern and remove cistern
lid.
2
Flush the cistern and remove any loose dirt from
inside the tank.
3
Disconnect and remove the existing inlet valve.
B : INSTALLATION
If pressure < 1 bar (15 p.s.i) :
cut here (gravity pressure/ header tank)
1
Insert correct filter restrictor into threaded tail.
If pressure < 1 bar (15 p.s.i.) :
If pressure < 1 bar (15 p.s.i) :
cut here (gravity pressure/ header tank)
cut here (gravity pressure / header tank)
Float
Float basin
Threaded tail
Rubber washer
Back nut
Filter restrictor
2 Fit the filling valve. Ensure that the valve does not obstruct
2
- Fit the filling valve. Ensure that the valve does not obstruct the
2
- Fit the filling valve. Ensure that the valve does not obstruct the
flush mechanism. Do not overtighten the back nut.
the flush mechanism. Do not overtighten the back nut
flush mechanism. Do not overtighten the back nut.
OK
3
Important for new installations : before turning water on,
ensure that one cold water tap is open so that dirt and loose
particles in the pipe work are flushed through the tap (we
also recommend to flush through the water supply pipe to the
cistern before connection is made.
4
.
Connect water supply
5
Turn on water supply. Allow the cistern to fill,
A
Adjust the water level,
Assembly instruction leaflet
• Jollyfill telescopic bottom entry inlet valve
Adjustment rod
6
.
NOT OK
6
A
A
A
25 mm minimum
from internal overflow to
critical level (CL)
on inlet valve.
I n ternal overfl o w
A
Wat e r l i n e 2 cm
25 mm minimum
from internal overflow to
critical level (CL)
on inlet valve.
Internal overflow
Waterl i n e 2 cm
B
If the water level is not correct, turn off water supply.
Adjust the water level by : Turning slowly right or left to open.
Pulling up the body of the telescopic part, (see pic B).
Turning slowly right or left to lock. Turn on water supply.
C
You can precisely adjust the float basin
with the red rod. Unclip the red rod min 0 to
max
150mm
Adjust the float basin Clip the red rod.
OK
min 0 to
max
150mm
Place the base seal over threaded section and feed through bottom of
OK
cistern. Secure hand-tight plus half a turn using back-nut supplied
TROUBLE SHOOTING MAINTENANCE
(using a suitable spanner). Shown below are bolted and plated kit
assemblies for close coupled WC pans and cisterns.
FOR JOLLYFILL SIDE AND BOTTOM ENTRY VALVES
BOLTED KIT
A
Bolt
Turn off water supply before any maintenance is carried out.
1
A Plastic Sleeve
BOTTOM ENTRY
Plastic Washer
Cistern
! Plastic Washer
Metal Nut
Pan
Plastic Washer
Metal Wing Nut
B
2 Remove and wash
the diaphragm
and reassemble in
reverse order.
!
3
Remove and wash
3
the filter restrictor
and reassemble in
reverse order.
A
25 mm minimum
from internal overflow to
critical level (CL)
on inlet valve.
Internal overfl o w
Wat e r l i n e
2 cm
B
C
min 0 to
max
150mm
NOT OK
OK NOT OK
NOT OK
PLATED KIT
B
Back-Nut
Cistern Base
1
B
SIDE ENTRY
A
B
2
Plate
WC Pan
Bolt
Rubber Washer
Metal Washer
Finger Nut
SANITARY EQUIPMENT SPECIALIST
min 0 to
max
150mm
OK
(Photo 8)
!
(Scheme 9)
1