Page 1
INSTRUCTION MANUAL CCD CAMERA CG-301 Series...
Page 2
WARNING – TO PREVENT RISK OF FIRE OR SHOCK, DO NOT EXPOSE THIS CAMERA TO RAIN OR MOISTURE. PRECAUTION : DO NOT REMOVE ANY COVER WHILE THE CAMERA IS OPERATING. PAL : USE ONLY RECOMMENDED POWER SUPPLY, 24 VAC (20.4 to 27.6 VAC) 50 Hz or 12VDC(10.2 to13.8VDC).
CONTENTS Section Page IMPORTANT SAFEGUARDS INTRODUCTION CAUTIONS FOR OPERATION EXTERNAL CONTROLS AND CONNECTORS LENS ELECTRONIC CONNECTIONS MECHANICAL CONNECTION BACK FOCAL ADJUSTMENT POWER CONNECTION AC POWER CONNECTION DC POWER CONNECTION SETUP MENU SETTING METHOD SETTING OPERATION SETUP ITEMS MODE SELECT EXPOSURE SET. FUNCTION SET.
IMPORTANT SAFEGUARDS 1. Read Instructions–All the safety and operating instructions should be read before the camera is operated. 2. Retain Instructions–The safety and operating instructions should be retained for future reference. 3. Heed Warnings–All warnings on the camera and in the operating instructions should be adhered 4.
Page 5
14. Overloading–Do not overload wall outlet and extension cord, as this can result in a risk of fire or electric shock. 15. Object and Liquid Entry–Never push objects of any kind into the camera through openings, as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the camera.
INTRODUCTION Thank you for purchasing this product. This product is a multiple function and a high quality CCD camera developed considering a high-end security. The following functions are built-in: (1) Wide Dynamic Range function This function makes it possible to capture both high-luminance and low-luminance subjects. Dynamic Range of max.60 dB.
EXTERNAL CONTROLS AND CONNECTORS CAMERA MOUNT ADAPTER BACK VIEW TOP/FRONT VIEW Fig.1 ① Lens Mount The camera has a standard CS lens mount but can use a C-mount lens when a C/CS-mount adapter is installed between the lens and camera. ②...
LENS This camera can accommodate DC voltage drive auto-iris lens. VIDEO signal controlled lens is not available. ELECTRONIC CONNECTIONS Table.1 shows wiring scheme for the 4pin Auto iris connector. Lens Connector Auto-iris Lens Table 1 DC VOLTAGE DRIVE Connector AUTO-IRIS LENS Pin No.
BACK FOCAL LENGTH ADJUSTMENT The camera has been factory-adjusted for the proper back focal length using a standard CS Mount lens. However, when the lens is mounted, it may be necessary to readjust back focal length to match the lens being used.
POWER CONNECTION This camera uses 24VAC or 12VDC power supply for the main supply. CAUTION : Take care not to short-circuit the power line wire, when connecting the power-supply cord to the camera. AC POWER CONNECTION A main supply of 24VAC (20.4 to 27.6 VAC) 50 / 60Hz is required. This main supply must also have a minimum rating of 270mA.
SETUP MENU This product built in OSD function and can customize the camera setting. The menu list is shown in the following. MODE SELECT STANDARD DAY&NIGHT WIDE CASINO USER MODE RETURN EXPOSURE SET. MAIN MENU AE MODE → WD MODE SELECT LENS ADJUSTMENT LEVEL →...
Page 12
SYNC SELECT PHASE SHIFT SYNC MODE AUTO PHASE → Phase Value = 28 RETURN *Only when AUTO is selected CHROMA RY GAIN → BY GAIN → RY HUE → BY HUE → RETURN E-ZOOM POSITION ZOOM → OFF POSITION RETURN *Only when the zoom magnification is selected MASKING MASK SETTING...
SETTING METHOD This camera has multiple functions, and can be adapted to a shooting place. There are 2 methods which are specified functions of the camera. (1) Setting method by using OSD(On-screen Display) function. Refer to the next section in details. (2) Setting method by using Direct-key function.
SETTING OPERATION This camera has OSD function. To change settings on the menu, operate the following procedure. 1. Press and hold down the SW for 2 seconds or more. The SW on the rear panel is used. (Fig.1 ⑧) 2. MAIN MENU appears on the monitor as shown in Fig.7-5. 3.
Page 15
Parameters of each mode is shown in Fig.7-7,7-8,7-9,7-10. STANDARD FUNCTION SET. EXPOSURE SET. → NORMAL SYNC SELECT → AUTO AE MODE → WHITE BALANCE → AUTO LEVEL → → FLICKERLESS CROMA → → NORMAL GAMMA → → SENS UP E-ZOOM →...
(2) EXPOSURE SET. In this menu, the exposure system of the camera can be specified. There are 2 kinds of EXPOSURE SET. menu. A. AE MODE other than MANUAL B. MANUAL is selected for AE MODE EXPOSURE SET. EXPOSURE SET. →...
Page 17
DAY & NIGHT This item specifies the switch between Color and BW picture. AUTO : Auto mode enables the camera to switch between Color and BW picture in response to light condition. COLOR : Fixes to Color picture. BW : Fixes to BW picture. EXT.
(3) FUNCTION SET. In this menu, functions other than exposure system can be specified. EXPOSURE SET. → SYNC SELECT → AUTO WHITE BALANCE → CROMA → NORMAL GAMMA → E-ZOOM → MASKING → TITLE RETURN Fig.9-1 FUNCTION SET. menu (3-1)SYNC SELECT This camera supports the synchronization mode such as line lock and internal.
Page 19
(3-2) WHITE BALANCE WHITE BALANCE You can select one of 4 modes for white balance adjustment as follows. AUTO, HOLD, INDOOR (Approx. 2800K), OUTDOOR (Approx. 6000K) AUTO : The white balance is adjusted automatically to provide the optimum picture. HOLD : In this mode, the WB gain just before changing to this mode is kept. INDOOR, OUTDOOR : These modes are the fixed WB gain.
Page 20
(3-5) E-ZOOM This camera built in electronic zoom, electronic panning and electronic tilting function. In this menu, these functions is specified. E-ZOOM POSITION ZOOM → 2.0 POSITION → RETURN Fig.9-5 E-ZOOM menu ZOOM The zoom magnification is selected from the following. OFF, 1.5, 2.0, 2.5 Note) When 1.5, 2.0 or 2.5 is selected, WD and MASKING function is not available.
Page 21
3. The pointer is displayed on the monitor screen. The area of a mask can be edited by using this pointer. At first, move the cursor to the upper left position you want to make a mask and press the SW.
(4) CAMERA SETUP This camera has an external control input interface (RS-485). All parameters and adjustments can be changed from an external unit. Refer to the section on External Control Input Terminal in details. In this menu, setting of the communication, LED and Switch can be selected. CAMERA SETUP →...
(6) MODE SAVE Current settings can be saved. Saved settings can read by selecting USER MODE of MODE SELECT. MODE SAVE CURRENT SETTINGS ARE SAVED. CANCEL Fig.12 MODE SAVE menu Operation procedure 1. After changing parameters and adjustments, move the cursor to MODE SAVE and press the SW. MODE SAVE menu is displayed.
(8) INITIALIZE Present settings are reset to the factory default settings. INITIALIZE ALL SETTINGS ARE IINITIALIZED Fig. 8 INITIALIZE MENU CANCEL Fig.14 INITIALIZE menu Operation procedure 1. Move the cursor to INITIALIZE and press the SW. INITIALIZE menu is displayed. 2.
EXTERNAL CONTROL INPUT TERMINAL This camera has an external control input terminal and can be operated remotely by supplying a control signal to this terminal. CONNECTIONS Connections of control signals are as follows. Pin1 Pin7 Magnified Figure Fig.16 Pin No. Description A (+) B (-)
SETUP To make up the camera system with RS-485, do the following procedure. Setting procedure 1. Connect the cable for each camera. 2. Terminate the camera installed in the end of the system. Turn off the termination of other cameras. Refer to Fig.1 ⑥...
SPECIFICATIONS Model Name CG-301 TV System NTSC Power AC24V(±15%) / DC12V(±15%) Power Consumption 270mA(24VAC) / 390mA(12VDC) Imager 1/3” Image Format vertical double density Interline transfer CCD Picture Elements (active) Approx. 380K pixels Approx. 440K pixels Synchronization Internal / LineLock Signal to Noise Ratio 48dB(AGC off, weighting) Video Output 1.0Vp-p/ Composite (75ohms)