Remington XR7000 - Electric Shaver Use And Care Guide

Table of Contents

Contents

1 PRODUCT FEATURES
2 SPECIFICATIONS
3 CHARGING
4 SHAVING YOUR HEAD
5 POP-UP TRIMMER
6 CLEANING YOUR SHAVER
7 TROUBLESHOOTING
8 SHAVER REPLACEMENT PARTS
9 PRODUCT DISPOSAL
10 Documents / Resources
- 10.1 References
- 10.2 Download manual

PRODUCT FEATURES

Register Your New Product Today!
By registering your new Remington^® product, you will receive special offers.
Register online at: RemingtonProducts.com

PRODUCT FEATURES
SHAVER PARTS

On/Off Switch
Shaving Head
Pop Up Trimmer (not shown)
360° Pivoting Neck
LED Battery Indicators
Hair Pocket

Charging Pins
Power Adaptor
Head Guard

Also Includes (Not Shown):

Cleaning Brush
Shaver Lubricant

SPECIFICATIONS

Power System	Cordless
Initial Charge Time	4 Hours
Full Charge Time	4 Hours
Cordless Run Time	Up to 50 Minutes
Indicators	2 LEDs (Low / Charging / Full Charge)
Voltage Type	Worldwide 100 - 240V
Waterproof	Yes
Replacement Head and Cutters	SPR-XR7000

Power System: Cordless - shaver can only be used when disconnected from the charging adaptor. The shaver will not run while it is charging.

To preserve the life of the battery: do not charge the battery after each use. The best practice is to use the shaver until the red low charge indicator appears and then recharge.

Indicators:

Low Charge: Flashes red when the shaver needs to be recharged.
Charging: When plugged in, the charging indicator will light up green.
Full Charge: Green LED indicator will turn off.

Note: Some countries will require the use of a plug adaptor that is not included with your shaver.

CHARGING

Before using, read the important safety instructions in this manual.

Ensure the product is switched off. Connect the shaver to the adaptor
Connect to a power outlet and charge for 4 hours when using for the first time. This first charge is important to the shaver's battery life.
When plugged in, the charging indicator will light up green.
When empty, the battery should be charged for 4 hours for a full charge and will provide up to 50 minutes of shaving time.
To preserve the life of the battery do not charge the battery after each use. Best practice is to use the shaver until the red low charge indicator appears and then recharge.

Make sure the shaver and your hands are dry when charging the shaver.
Always charge the shaver in a cool, dry place.

SHAVING YOUR HEAD

GUIDELINES

Do not attempt to shave head hair that is longer than 4 days growth or 2.0 mm. The Balder Head Shaver is intended to maintain the shaved look and can be used daily or every two or three days.
The Balder Head Shaver cannot shave long hair down to the shaved length. If your hair is longer than 2.0 mm you should trim it down with a hair clipper first before using the head shaver.
The Balder Head Shaver can be used dry or it can be used with shaving cream or gel in the shower.

Hold the head shaver body in the palm of your hand. Press the On/Off switch to turn the head shaver on.
Press the five cutting heads against your scalp. It is not necessary to press hard to shave. Pressing hard does not cut closer and could increase irritation. The cutting head will flex to follow the contours of your head.
Move the shaver slowly around your head. You may use linear strokes, or rotating motion, whichever you feel is most effective picking up and cutting your hair.
Use a hand held mirror to check the back of your head to confirm a complete and thorough shave. You may also use your other hand to feel for complete and consistent cutting.
It is not recommended to use the head shaver for facial hair.
When finished turn the shaver off. Check for the red low charge indication.

POP-UP TRIMMER

The pop-up trimmer is located at the back of the shaver handle. It can be used for trimming edges of beards, sideburns or ears.

To activate the trimmer, turn the shaver on. Slide the release button for the trimmer down to pop the trimmer up (A).
Use cutting strokes in the direction opposite of the trimmers spring release. (B)
When finished press the trimmer down and snap it back into the stored position. (C)

Note: Lubricate teeth with oil every 6 months.

CLEANING YOUR SHAVER

The Balder Head Shaver is designed to collect all the hair clippings while it cuts. This avoids clippings from spilling onto bathroom counters or shower stalls, making clean up easy.

When cleaning the shaver make sure it is turned off and disconnected from the charging adapter cord.
The shaver is washable and can be cleaned by rinsing under warm water.
When using shave creams or gels with the shaver it is especially important to clean after each use to prevent the gel from drying and clogging the cutters.

After every use:

Hold the shaver over the garbage can and remove the top of the cutting head. Remove the head by gripping in the areas between the four outer cutters and pulling up and away from the handle. (D)
Tap the excess clippings that have been collected inside the hair pocket into the garbage can. (E)
Rinse the cutting head thoroughly by running water through the cutters from both sides of the head.
Rinse the hair pocket under running water.
Leave the cutting head detached and let it air dry. Reattach the shaving head when dry and you are ready for the next use. (F)
Lubricate the cutters on the inside surface with one drop of lubricant per cutter once per week to maintain performance.

Blades are not to be removed from the head.
Deep Clean: After rinsing away bulk debris, reassemble the razor and turn on, submerge cutter head in warm water (add soap few drops of dish soap) and run for 15 sec. Remove the shaver head from hair pocket, thoroughly rinse and brush away loosened build up.
NOTE: Cleaning and lubricating before and after each use are essential with this device. Critical if wet shaving with foams or gels.
NOTE: Blades are permanently mounted in the head and are not to be removed for cleaning. Blades cannot or should not be reinstalled due to possible damage to cutter, screen, or retaining ring.

TROUBLESHOOTING

If the shaver is making a chugging noise, clean and re-lubricate the underside of the cutting heads. Be sure to clean shaver after each use and lubricate weekly.
Always firmly press the center of the on/off button when turning shaver on or off.

SHAVER REPLACEMENT PARTS

Please refer to the specifications' table in this manual that lists the correct replacement part number for your shaver.
It is very important to replace the shaving heads and cutters when necessary to ensure a close, comfortable shave without irritation. We recommend they be replaced every 12 months. Here are some signs of head and cutter wear, indicating that replacement is needed:

Irritation: As the heads get excessively worn you may experience some skin irritation. This would be especially noticeable when you apply moisturizing lotion.
Pulling: When the cutters wear you may feel a sense of pulling and a loss of closeness when you shave. This is an indication that it is time to replace the shaving heads and cutters.

The replacement cutting head for your shaver is model number SPR-XR7000.

How to Order Parts and Accessories

Order Online: RemingtonProducts.com

PRODUCT DISPOSAL

When your rechargeable shaver reaches the end of its useful life, the batteries must be removed from the shaver and be recycled or disposed of properly in accordance with your state and local requirements. If this is not required by law, you may elect to dispose of the shaver with the batteries.

Do not put in fire or mutilate your batteries when disposing as they may burst and release toxic materials. Do not short circuit as it may cause burns. Dispose of properly in accordance with your local and state requirements.

To Remove the Rechargeable Battery:

Unplug the shaver
Run shaver until the motor stops
Pull off the shaver head assembly.
Unscrew the screw on the top of the unit.
Pry off the upper decorative panel.
Pry off the two decorative side panels.
Unscrew the 6 screws on the inner housing.
Pry off the inner housing to expose the printed circuit board.
Take out the printed circuit board assembly.
Disconnect the battery from the circuit board.
Dispose of battery properly

At the end of this product's life, you can mail it to Spectrum Brands at 507 Stokely Drive, DeForest, WI 53532 marked "Product Takeback: Please Recycle!"