Table of Contents
Advertisement
Quick Links
INSTALLATION INSTRUCTIONS
NI-9695 sbRIO Thermal Solution
A 4.5 mm socket driver and a #1 Phillips screwdriver are required to install the
Note
NI-9695.
3
2
1
1 Heat Spreader (1X)
2 M3x16 mm Standoff, 4.5mm Hex (4X)
3 M3x18 mm Standoff, 4.5mm Hex (2X)
The National Instruments NI-9695 thermal kit is a heat
spreader accessory used to improve the thermal performance
of the sbRIO-9605/9606/9623/9626/9633/9636.
The NI-9695 contains the following components.
Figure 1. NI-9695 Part Locator Diagram
4 M3 Pan Head Screw (6X)
5 Pre-Cut Gap Pad (1X)
4
5
Advertisement
Table of Contents
Summary of Contents for National Instruments NI-9695
- Page 1 INSTALLATION INSTRUCTIONS NI-9695 sbRIO Thermal Solution The National Instruments NI-9695 thermal kit is a heat spreader accessory used to improve the thermal performance of the sbRIO-9605/9606/9623/9626/9633/9636. A 4.5 mm socket driver and a #1 Phillips screwdriver are required to install the Note NI-9695.
-
Page 2: Mounting And Environmental Considerations
Mounting and Environmental Considerations The heat spreader provided in NI-9695 is intended to improve the thermal performance of sbRIO by removing heat from the components that may limit the device's maximum operating temperature. The mounting configuration of the heat spreader can also influence the device's maximum operating temperature. - Page 3 White Side of Gap Pad Pink Side of Gap Pad Clear Un-Cut Liner Peel back Figure 3. Side View and Layers of Gap Pad Figure 4. Gap Pad Placement on Heat Spreader © National Instruments NI 9695 sbRIO Thermal Solution...
- Page 4 Installing the NI 9695 The section provides installation procedures for the following example configurations. • Installing the flat face of the heat spreader to the base mounting surface • Installing with the flat face of the heat spreader exposed to air •...
- Page 5 It is recommended to fasten these screws at a rate below 10 in/min. © National Instruments NI 9695 sbRIO Thermal Solution...
- Page 6 Installing With the Flat Face of the Heat Spreader Exposed to Air 1 16 mm Standoff 2 Not Provided Figure 6. Heat Spreader to sbRIO: Flat Face Exposed to Air Remove gap pad pieces from both liners and apply pink side to heat spreader pads.
- Page 7 Figure 7 shows one example of an RMC being installed to a sbRIO-9626 with the flat face of the heat spreader mated to the base mounting surface. 1 16 mm Standoff 2 Not Provided 3 18 mm Standoff Figure 7. Heat Spreader to sbRIO: With RMC © National Instruments NI 9695 sbRIO Thermal Solution...
-
Page 8: Specifications
(5 mm) from the board surface. In addition, the component temperatures should not exceed their recommended maximum case temperatures. Systems that use the heat spreader provided in NI-9695 have the option of only measuring the heat spreader temperature in NI 9695 sbRIO Thermal Solution... -
Page 9: Environmental Management
For additional environmental information, refer to the NI and the Environment Web page at . This page contains the ni.com/environment environmental regulations and directives with which NI complies, as well as other environmental information not included in this document. © National Instruments NI 9695 sbRIO Thermal Solution... -
Page 10: Waste Electrical And Electronic Equipment (Weee)
(For information about China RoHS compliance, go to ni.com/environment/rohs_china Where to Go for Support The National Instruments Web site is your complete resource for technical support. At you have access to everything from ni.com/support troubleshooting and application development self-help resources to email and phone assistance from NI Application Engineers. - Page 11 For patents covering National Instruments products/technology, refer to the appropriate location: Help»Patents in your software, the patents.txt file on your media, or the National Instruments Patent Notice at ni.com/patents. Refer to the Export Compliance Information at ni.com/legal/ export-compliance for the National Instruments global trade compliance policy and how to obtain relevant HTS codes, ECCNs, and other import/export data.
Need help?
Do you have a question about the NI-9695 and is the answer not in the manual?
Questions and answers